Brother BAS-326G PS Instruction Manual page 75

Upper shaft motor-related errors
Code
Needle up stop position error.
E110
Turn the machine pulley until the point where the error display disappears.
Upper shaft did not stop at the needle up stop position when the sewing machine stopped.
E111
Turn the machine pulley until the point where the error display disappears.
Needle drop signal could not be detected.
E120
Turn off the power, and then check the synchronizer connection.
Thread trimming was not completed.
E121
Turn off the power, and then check if the cutting edges of the fixed knife and movable knife are damaged or worn.
Sewing machine motor stopped due to a problem, or synchronizer is faulty.
E130
Turn off the power, and then turn the machine pulley and check if the sewing machine has locked up.
Check that connectors P4 and P5 on the power supply motor P.C. board are properly connected.
Synchronizer is faulty.
E131
Turn off the power, and then check that connector P5 on the power supply motor P. C. board is properly connected.
Problem detected with sewing machine motor operation.
E132
Turn off the power, and then check that connector P4 on the power supply motor P.C. board is properly connected.
Sewing machine motor stopping position is incorrect.
E133
Turn off the power, and then check that connector P5 on the power supply motor P.C. board is properly connected.
Sewing machine motor is overheating, or temperature sensor is faulty.
Turn off the power, and then check the sewing machine motor.
E150
(When sewing data with a small number of stitches (15 stitches or less) is sewn repeatedly (short cycle operation),
the upper shaft motor may overheat and the "E150" error code may be generated.)
Feed mechanism-related errors
Code
X-feed motor home position cannot be detected.
Problem with X -feed motor or poor X home position sensor connection.
E200
Turn off the power, and then check that connector P10 on the PMD P.C. board and connector P20 on the main P.C.
board are properly connected.
X-feed motor stopped due to a problem.
E201
Turn off the power, and then check if there are any problems in the X-feed direction.
Problem with X-feed motor or Y-feed motor home position adjustment data.
E202
Re-adjust the home position.
X-feed motor stopped due to a problem during sewing.
E204
Turn off the power, and then check if there are any problems in the X-feed direction.
X-feed motor stopped due to a problem while moving to the sewing start position.
E205
Turn off the power, and then check if there are any problems in the X-feed direction.
X-feed motor stopped due to a problem during test feeding.
E206
Turn off the power, and then check if there are any problems in the X-feed direction.
X-feed motor stopped due to a problem during programming.
E207
Turn off the power, and then check if there are any problems in the X-feed direction.
Y-feed motor home position cannot be detected.
Problem with Y-feed motor or poor Y home position sensor connection.
E210
Turn off the power, and then check that connector P8 on the PMD P.C. board and connector P4 on the main P.C.
board are properly connected.
Y-feed motor stopped due to a problem.
E211
Turn off the power, and then check if there are any problems in the Y-feed direction.
Y-feed motor stopped due to a problem during sewing.
E214
Turn off the power, and then check if there are any problems in the Y-feed direction.
Y-feed motor stopped due to a problem while moving to the sewing start position.
E215
Turn off the power, and then check if there are any problems in the Y-feed direction.
Y-feed motor stopped due to a problem during test feeding.
E216
Turn off the power, and then check if there are any problems in the Y-feed direction.
Y-feed motor stopped due to a problem during programming.
E217
Turn off the power, and then check if there are any problems in the Y-feed direction.
Cause and remedy
Cause and remedy
BAS-326G PS
11. TABLE OF ERROR CODES
66