Page 1: Introduction
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3: Table Of Contents
CONTENTS Introduction ......4 A Message From DaimlerChrysler Corporation . . . 5 How To Use This Manual ....5 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5: A Message From Daimlerchrysler Corporation
A MESSAGE FROM DAIMLERCHRYSLER CORPORATION DaimlerChrysler Corporation and Cummins welcome you as a new Dodge Ram Cummins Turbo Diesel- powered truck owner. Almost 100% of the heavy duty trucks in the United States are diesel powered because of the fuel economy, rugged durability, and high torque which permits pulling heavy loads.
Page 6 6 INTRODUCTION...
Page 7: Van Conversions/Campers
WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information.
Page 8: Vehicle Identification Number
8 INTRODUCTION VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears on the Auto- mobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title.
Page 9: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Ignition Key Removal ....12 Locking Doors With The Key .
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock The Doors ....20 To Lock The Doors .....21 Using The Panic Alarm .
Page 11 Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbag ... .45 Event Data Recorder (EDR) ....56 Child Restraint .
Page 12: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place.
Page 13 NOTE: If you try to remove the key before you place the lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable.
Page 14: Locking Doors With The Key
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Manual Transmission—If Equipped When the steering wheel is in the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your vehicle. It may be difficult to turn the key from the LOCK position when starting your vehicle.
Page 15: Steering Wheel Lock - If Equipped
STEERING WHEEL LOCK — IF EQUIPPED Your vehicle may be equipped with a passive steering wheel lock. This lock prevents steering the vehicle with- out the ignition key. If the steering wheel is moved no more than 1/2 turn in either direction and the key is not in the ignition switch, the steering wheel will lock.
Page 16: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the vehicle. The system will shut the engine off in two (2) seconds if someone uses an invalid key to start the engine. NOTE: A key, which has not been programmed, is also considered an invalid key even if it is cut to fit the ignition lock cylinder for that vehicle.
Page 17: Customer Key Programming
NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer. Customer Key Programming You can program new keys to the system if you have two valid keys by doing the following: 1. Cut the additional Sentry Key Transponder blank(s) to match the ignition switch lock cylinder key code.
Page 18: General Information
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information The Sentry Key system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. •...
Page 19: To Disarm The System
NOTE: If the SECURITY light stays on continuously during vehicle operation, have the system checked by your dealer. To Disarm the System: Use the Keyless Entry transmitter to unlock the door. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the security lamp will flash for 30 seconds.
Page 20: Remote Keyless Entry - If Equipped
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY — IF EQUIPPED Three Button Transmitter This system allows you to lock or unlock the doors from distances up to about 23 feet (7 meters) using a hand held radio transmitter.
Page 21: To Lock The Doors
5. This will enable you to unlock all doors on the first press of the UNLOCK button. To lock the doors: Press and release the LOCK button on the transmitter to lock all doors. If the ignition is OFF, when the doors are locked, the parking lights will flash on once and the horn will chirp once.
Page 22: Using The Panic Alarm
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Using the Panic Alarm To activate the Panic mode while the ignition is OFF press and release the PANIC button on the transmitter once. When the Panic mode is activated, the interior lights will illuminate, the headlamps and parking lights will flash, and the horn will sound.
Page 23: Transmitter Battery Service
Transmitter Battery Service Transmitter Battery Replacement The recommended replacement battery is a 3V lithium 2016 cell. This transmitter requires two batteries. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 1.
Page 24: Door Locks
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS Manual Door Locks Front and Rear doors may be locked, by moving the lock plunger up or down. All doors may be opened with the inside door handle without lifting the lock plunger. Doors locked before closing will remain locked when closed.
Page 25: Power Door Locks - If Equipped
Power Door Locks — If Equipped A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. Power Door Lock Switch Location If you press the power door lock switch while the key is in the ignition, and any front door is open, the power THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 locks will not operate.
Page 26 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Fasten your seat belt (Fastening the seat belt will cancel any chiming that may confuse you during this programming procedure). 3. Place the key into the ignition. 4. Within 15 seconds cycle the key from the LOCK position to the ON/RUN position a minimum of four times;...
Page 27: Child Protection Door Lock
4. Within 15 seconds, cycle the key from the LOCK position to the ON/RUN position a minimum of four times ending in the LOCK position (do not start the engine). 5. Within 30 seconds, press the driver’s door lock switch in the UNLOCK direction.
Page 28 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE slide the lever UP to engage the locks and DOWN to disengage the child-protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position.
Page 29: Windows
WINDOWS Power Windows—If Equipped Power Window Switches The control on the left front door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 and on the rear doors of Quad Cab and Mega Cab models.
Page 30: Power Sliding Rear Window-If Equipped
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Window Lockout Switch (4 Door Models Only) The window lockout switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window lock button.
Page 31: Sliding Rear Window-If Equipped
Sliding Rear Window—If Equipped A locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears.
Page 32: Lap/Shoulder Belts
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle.
Page 33 WARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Page 34 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt.
Page 35 Latch Plate To Buckle THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you.
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt.
Page 37 5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt. 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position.
Page 38 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The black buckle latch plate can be removed when the key is pressed into the buckle. Allow the retractor to take up the surplus webbing, and the buckles will hang vertically from the cab back exit bezel, thus freeing up all the area behind the front seats.
Page 39 WARNING! • If the black latch and black buckle are not prop- erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision.
Page 40: Adjustable Upper Shoulder Belt Anchorage
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In Use Position WARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly. Adjustable Upper Shoulder Belt Anchorage In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck.
Page 41: Automatic Locking Restraint (Alr) Mode - If Equipped
Adjusting Upper Shoulder Belt As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position.
Page 42: Center Lap Belts
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How To Disengage The Automatic Locking Mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic lock- ing mode and activate the vehicle sensitive (emergency)
Page 43: Enhanced Driver Seat Belt Reminder System (Beltalert)
NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly. The pretensioners are triggered by the airbag control module. Like the airbags, the pretensioners are single use items.
Page 44: Seat Belts And Pregnant Women
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled. 4. Turn off the engine. A single chime will sound to signify that you have successfully completed the pro- gramming.
Page 45: Driver And Right Front Passenger Supplemental Restraint System (Srs)-Airbag
WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the seat belt extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you.
Page 47 Here are some simple steps you can follow to minimize the risk of harm from a deploying airbag. • Children 12 years and under should ride buckled up in a rear seat, if available. • Infants in rear facing child restraints must NEVER ride in the front seat of a vehicle with a passenger front airbag unless the airbag is turned off (Standard Cab Vehicles Only).
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
Page 49 The Window Airbag System, on vehicles equipped, consists of the following: • AIRBAG Readiness Light (shared with the front airbag system) • Window Bags Above the Side Windows. • Airbag Control Module (shared with the front airbag system) • Side impact sensors •...
Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the AIR BAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
Page 51 Passenger Airbag On/Off Switch – (Standard Cab Vehicles Only) The passenger front airbag is to be turned off only if the passenger: • is an infant (less than 1 year old) who must ride in the front seat because there is no rear seat, because the rear seat is too small for a rear-facing infant restraint or THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 because the infant has a medical condition which...
Page 52 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Whenever an airbag is turned off, even a lap/ shoulder belted passenger may hit their head, neck, or chest on the dashboard (instrument panel) or windshield in a crash. This may result in serious injury or death.
Page 53 If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor.
Page 54 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Window Airbags Supplemental Restraint System (SRS)—If Equipped The window airbag control module determines if a side collision is severe enough to require the side airbags to inflate. The window airbag control module will not detect roll over, front or rear collisions.
Page 55 Maintaining Your Airbag Systems WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
Page 56: Event Data Recorder (Edr)
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE for blown fuses. Refer to the label located on the inside of the fuse block cover for the proper airbag fuses. See your dealer if the fuse is good. Event Data Recorder (EDR) In the event of an airbag deployment, your vehicle is designed to record up to 2-seconds of specific vehicle data parameters (see the following list) in the event data...
Page 57: Child Restraint
nature, such as would identify a particular driver, ve- hicle, or crash, will be treated confidentially. Confidential data will not be disclosed by DaimlerChrysler Corpora- tion to any third party except when: 1. Used for research purposes, such as to match data with a particular crash record in an aggregate database, provided confidentiality of personal data is thereafter preserved...
Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children 12 years and under should ride properly buck- led up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front. WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle.
Page 59 infant carriers do, so they can be used rearward-facing by children who weigh more than 20 lbs (9 kg) but are less than one year old. • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag unless the airbag is turned off.
Page 60 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint.
Page 61 Pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide the latch plate into the buckle. Then pull on the belt until it is all removed from the retractor. Allow the belt to return to the retractor, pulling on the excess web- bing to tighten the lap portion about the child re- straint.
Page 62 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when install- ing an infant or child restraint.
Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Mega Cab Rear Seats Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage have been available for Quad Cab Rear Outboard Seats...
Page 64 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products. Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchor- ages will continue to have features for installation in vehicles using the lap or lap/shoulder belt.
Page 65 Installing the Child Restraint System WARNING! Do not install child restraint systems equipped with LATCH attachments in the center position of a Quad Cab model rear seat. The LATCH anchorages in this seat are designed for the two outboard seating posi- tions only.
Page 66 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
Page 67 2. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal. 3. Install the child restraint and remove the slack in the tether strap according to the manufacturer’s instructions. Regular Cab Tether Strap Mounting THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Multiple Child Restraint Installation Sequence - (Quad Cab Rear Seats)
Page 68 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Place a child restraint on the center rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat and to the anchor directly behind the right seat.
Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Multiple Child Restraint Quad Cab...
Page 70 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tether Anchorage Points at All Three Seating Positions (Mega Cab) 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seat back under the head restraint to the tether anchor directly behind the seat.
Page 71: New Engine Break-In
• The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle.
Page 72: Safety Tips
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! • During the first 500 miles (805 km) your new vehicle is driven, do not tow a trailer. Doing so may damage your vehicle. • Limit your speed to 50 mph (80 km/h) during the first 500 miles (805 km) of towing.
Page 73: Exhaust Gas
Exhaust Gas WARNING! Exhaust gases contain carbon monoxide, a poten- tially toxic gas that by itself is colorless and odorless. To avoid inhaling these gases, the following precau- tions should be observed: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
Page 74: Safety Checks You Should Make Inside The Vehicle
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Heater Defroster Ducts Inspect the heater defroster ducts for proper operation. Check for proper air flow through all defroster ducts. If there are any question regarding the operation of your heater defroster ducts, have the system checked by an authorized dealer Seat Belts...
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Lights Check the operation of all exterior lights. Check turn signal and high beam indicator lights on the instrument panel. Door Latches Check for positive closing, latching and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, water, oil, or other fluid leaks.
Page 77: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......82 Inside Mirror ......82 Automatic Dimming Mirror—...
Page 78 78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Seats ..... . . 111 Adjustable Head Restraints ....111 Manual Rotary Lumbar Support Adjustment —...
Page 79 Electronic Speed Control — If Equipped ..133 To Activate ......133 To Set At A Desired Speed .
Page 80 80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Canadian Programming/Gate Programming . . 147 Using HomeLink ..... 148 Erasing HomeLink Buttons ....148 Reprogramming a Single HomeLink Button .
Page 81 Storage ......159 Center Storage Compartment (40–20–40 Seat) — If Equipped ......159 Center Storage Compartment (Bucket Seats)—...
Page 82: Mirrors
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Mirror The mirror should be adjusted to center on the view through the rear window. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
Page 83: Automatic Dimming Mirror- If Equipped
Automatic Dimming Mirror— If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will indicate when the dimming feature is activated.
Page 84: Exterior Mirrors Folding Feature
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with an- other vehicle or other object.
Page 85: Electric Rear Window Defroster And Heated Sideview Mirrors - If Equipped
Power Mirror Switches Set the top switch to the left or right for the left or right mirror, and set it to the center off position to prevent accidentally moving a mirror when you are finished adjusting the mirror. To adjust a mirror, select left or right with the top switch, and press one of the four arrows for the direction you want the mirror to move.
Page 86 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Fold the 7 x 10 inch trailer towing mirrors rearward prior to entering an automated car wash. Trailer Towing Position Blindspot Mirror...
Page 87: Hands-Free Communication (Uconnect™) - If Equipped
HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in- vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone using simple voice commands (e.g., Call” “Mike” ”Work or Dial” “248-555-1212 ). Your cellular phone’s audio is trans- mitted through your vehicle’s audio system;...
Page 88: Operations
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The rearview mirror contains the microphone for the system and the control buttons that will enable you to access the system. UConnect™ Switches The UConnect™ system can be used with any Hands- Free Profile certified Bluetooth™ cellular phone. See www.chrysler.com/uconnect for supported phones.
Page 89 • Prior to giving a voice command, one must wait for the voice on beep, which follows the Ready prompt or another prompt. • For certain operations, compound commands can be used. For example, instead of saying Setup and then Phone Pairing, the following compound command can be said: Setup Phone Pairing.
Page 90 NOTE: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin.
Page 91 • You will then be asked to give your cellular phone a priority level between 1 and 7, 1 being the highest priority. You can pair up to seven cellular phones to your UConnect™ system. However, at any given time, only one cellular phone can be in use, connected to your UConnect™...
Page 92 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the Ready prompt and the following beep, say the name of the person you want to call. For example, you can say John Doe, where John Doe is a previ- ously stored name entry in the UConnect™ phone- book.
Page 93 four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language. Edit Entries in the UConnect™ Phonebook NOTE: Editing phonebook entries is recommended when vehicle is not in motion. • Press the ’Phone’ button to begin. •...
Page 94 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say List Names to hear a list of the entries in the phonebook from which you choose.
Page 95: Phone Call Features
• To call one of the names in the list, press the Voice Recognition’ button during the playing of the desired name, and then say Call. NOTE: the user can also exercise Edit or Delete operations at this point. • The UConnect™ system will then prompt you as to number designation you wish to call.
Page 96 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Making a Second Call while Current Call in Progress To make a second call while you are currently in a call, press the ’Voice Recognition’ button and say Dial or Call followed by the phone number or phonebook entry you wish to call.
Page 97: Uconnect™ System Features
Call Termination To end a call in progress, momentarily press the Phone’ button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. Redial • Press the ’Phone’ button to begin. •...
Page 98 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the Ready prompt and the following beep, say the name of the language you wish to switch to (English, Espanol, or Francais, if so equipped). • Continue to follow the system prompts to complete language selection.
Page 99 Your phone must be turned on and paired to the UConnect™ system to allow use of this vehicle feature in emergency situations when the cell phone has network coverage and stays paired to the UConnect™ system. Towing Assistance If you need towing assistance, •...
Page 100 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When calling a number with your UConnect™ system that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can push the ’Voice Recognition’ button and say the sequence you wish to enter followed by the word Send.
Page 101 Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth™...
Page 102: Advanced Phone Connectivity
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Information Service When using AT&T Wireless Service, dialing to phone number #121, you can access voice activated automated system to receive news, weather, stocks, traffic, etc. related information. Advanced Phone Connectivity Transfer Call to and from Cellular Phone The UConnect™...
Page 103: Things You Should Know About Your Uconnect™ System
Select another Cellular Phone This feature allows you to select and start using another phone with the UConnect™ system. The phone must have been previously paired to the UConnect™ system that you want to use it with. • Press the ’Phone’ button to begin. •...
Page 104 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Speak normally, without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you. • Make sure that no one other than you is speaking during a voice recognition period. •...
Page 105 • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, and • dry weather condition. • Operation from driver seat. • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the UConnect™...
Page 106 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 107 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107...
Page 108 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 109: Seats
North American English Primary Alternate(s) Zero Add location Add new All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return.
Page 110: 40-20-40 Front Seat
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 40-20-40 Front Seat Manual Seat Adjuster As the name implies, the seat is divided into 3 segments. The outboard seat portions are each 40% of the total width of the seat. The back of the center portion (20%) easily folds down to provide an armrest/center storage compartment (if equipped).
Page 111: Reclining Seats
Reclining Seats The recliner handle is on the outside of the seat cushion. Pull up on the handle, as shown, to release the seat back and adjust for comfort. Manual Recline Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 WARNING! You can be seriously, even fatally, injured riding in a seat with the seatback reclined.
Page 112: Manual Rotary Lumbar Support Adjustment - If Equipped
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To lower the head restraint, push in the button and then push down on the head restraint. Head Restraints Manual Rotary Lumbar Support Adjustment — If Equipped Rotating the lumbar control knob on the left side of the driver’s seatback and on the right side of the passenger’s seatback increases or decreases the lumbar (lower back) support.
Page 113: Power Seats - If Equipped
Power Seats — If Equipped CAUTION! Don’t put anything under a power seat. It may cause damage to the seat controls. Power Seat Switch UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Up, Down, Forward, and Rearward The power seat controls are on the outboard side of the front seat cushions.
Page 114: Rear Seat Features - Mega Cab Models
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE control seat height. Change the seat angle by using the two toggle switches, tilting it up or down. Tilt Adjustment Rear Seat Features — Mega Cab Models Reclining Rear Seats — Mega Cab Models The recliner handle is on the outside of the seat cushion.
Page 115 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Folding Rear Seat (Table Mode) — Mega Cab Models Both the left and right rear seat backs can be folded down and used as a table. To fold either rear seat back down (Table Mode), lift the handle and fold the seat back forward.
Page 116 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Table Mode Folding Rear Seat (Kneel Mode) — Mega Cab Models Both the left and right rear seats can be folded flat (Kneel Mode) and used for carrying cargo. Each of the rear seat backs provide 2 D-rings and each of the rear storage bin lids provide 2 slotted cutouts.
Page 117 WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Page 118 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To fold either rear seat flat (Kneel Mode), lift the handle and fold the seat forward. Simply lift the seat back to return the seat to the upright position. Verify that it is locked in place.
Page 119: Heated Seats - If Equipped
WARNING! Be certain that the seatback is securely locked into position. If the seatback in not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. Heated Seats —...
Page 120 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE level, or OFF. The High heat level operates for 30 minutes (approximate), the Low heat level operates for 30 min- utes (approximate). The seat heat will also turn OFF when the ignition is turned OFF. Both of the indicators ON identifies High heat level.
Page 121: To Open And Close The Hood
TO OPEN AND CLOSE THE HOOD Hood Release Lever To open the hood, two latches must be released. First pull the hood release lever located below the steering wheel at the base of the instrument panel. Once the hood is UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 released you must reach into the opening beneath the center of the grille and push up the latch to release the...
Page 122: Lights
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are latched fully before driving. Headlight Switch Location...
Page 123: Interior Lights
Interior Lights Dimmer Control Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the upward detent position, or if equipped, when the UN- LOCK button is pressed on the key fob.
Page 124: Battery Saver
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Battery Saver To protect the life of your vehicle’s battery, Load Shed- ding is provided for both the interior and exterior lights. If the ignition is off and any door is left ajar for 10 minutes or the dimmer control is rotated upwards for 10 minutes, the interior lights will automatically turn off.
Page 125: Daytime Running Lights (Canada Only And Fleet Vehicles)
Light Switch Rotation Your vehicle is equipped with plastic headlight lenses that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth.
Page 126: Lights-On Reminder
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lights-on Reminder If the headlights, parking lights, or cargo lights are left on, after the ignition is turned off, a chime will sound when the driver’s door is opened. Fog Lights — If Equipped The foglights are turned ON by placing the head- light rotary control in the parking light or head- light position and pushing in the headlight rotary...
Page 127: Multifunction Control Lever
Multifunction Control Lever The multifunction control lever is located on the left side of the steering column. Turn Signals Move the lever up or down to signal a right-hand or left-hand turn. The arrow on either side of the instrument cluster flashes to indicate the direction of the turn, and proper operation of the front and rear turn signal lights.
Page 128 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Passing Light You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer- ing wheel. This will cause the high beam headlights to turn on until the lever is released. High Beam / Low Beam Select Switch Pull the multifunction control lever fully toward the steering wheel to switch the headlights from HIGH or...
Page 129: Windshield Wipers And Washers
WINDSHIELD WIPERS AND WASHERS Windshield Wipers Windshield Wiper / Washer Switch The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle,...
Page 130: Windshield Washers
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind- shield washer use.
Page 131 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped.
Page 132: Driver Adjustable Pedals - If Equipped
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER ADJUSTABLE PEDALS — IF EQUIPPED Adjustable Pedals Switch The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals. Adjustment 1. Position the driver seat so that you are at least 10 inches (254 mm) away from the airbag located in the center of the steering wheel.
Page 133: Electronic Speed Control - If Equipped
CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. ELECTRONIC SPEED CONTROL —...
Page 134: To Set At A Desired Speed
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Set At A Desired Speed When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. To Deactivate A soft tap on the brake pedal, normal braking, clutch pressure while slowing the vehicle, or pressing the CAN- CEL button will deactivate speed control without erasing...
Page 135: To Accelerate For Passing
To decrease speed while the speed control is on, press and hold the DECEL button. Release the button when the desired speed is reached, and the new speed will be set. To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed.
Page 136: Overhead Console- If Equipped
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE— IF EQUIPPED The two optional overhead consoles may consist of the following features: Overhead Console Features • Courtesy/Reading Lights • Compass/Temperature Mini-Trip Computer (CMTC) — If Equipped • Universal Garage Door Opener — If Equipped Courtesy/Reading Lights In the middle of the console are two courtesy/reading lights.
Page 137: Overhead Console With Compass/Temperature Mini-Trip Computer - If Equipped
OVERHEAD CONSOLE WITH COMPASS/TEMPERATURE MINI-TRIP COMPUTER — IF EQUIPPED This optional overhead console consists of the following: • Courtesy Lights • Compass/Temperature Mini-Trip Computer (CMTC) UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 This overhead console allows you to choose between a compass/temperature display and one of four trip con- ditions being monitored.
Page 138: Reset Button
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE RESET Button Use this button to reset the following displays: Average Fuel Economy (AVG ECO) Trip Odometer (ODO) Elapsed time (ET) Global Reset If the RESET button is pressed twice within 2 seconds while in any of the 3 resettable displays (AVG ECO, ODO, ET), the Global Reset will reset all 3 displays.
Page 139: Average Fuel Economy (Avg Eco)
Average Fuel Economy (AVG ECO) Shows the average fuel economy since the last reset. Average fuel economy is a running average of the amount of fuel used and the distance the vehicle has traveled. When the fuel economy is reset, the display will momen- tarily blank.
Page 140: Trip Odometer (Odo)
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ram fuel tank volumes are as follows: • 26 gallons - 1500 short box models • 34 gallons - 1500 Quad Cab (if equipped)/2500/3500 short box models • 35 gallons - 1500/2500/3500 long box models Trip Odometer (ODO) This display shows the distance traveled since the last reset.
Page 141: Automatic Compass Calibration
WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage. Automatic Compass Calibration This compass is self-calibrating which eliminates the need to manually set the compass.
Page 142 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Compass Variance is the difference between magnetic north and geographic north. In some areas of the country, the difference between magnetic and geographic north is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set according to the Compass Variance Map.
Page 143: Outside Temperature
NOTE: The default for the compass variance is zone 8. To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press and hold the RESET button approximately five seconds. The last vari- ance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
Page 144 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For additional information on HomeLink , call 1–800– 355–3515, or on the internet at www.homelink.com. WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured.
Page 145: Programming Homelink
Programming HomeLink NOTE: When programming a garage door opener, it is advised to park outside the garage. It is also recom- mended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmis- sion of the radio-frequency signal.
Page 146 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Simultaneously press and hold both the HomeLink button that you want to train and the hand-held trans- mitter buttons. Do not release the buttons until step 4 has been completed. NOTE: Some gate operators and garage door openers may require you to replace this Programming Step 3 with procedures noted in the Gate Operator/Canadian Pro- gramming section.
Page 147: Canadian Programming/Gate Programming
8. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink button. Repeat the press/hold/release sequence a second time, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming.
Page 148: Using Homelink
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLink To operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.).
Page 149: Security
Security If you sell your vehicle, be sure to erase the frequencies. To erase all of the previously trained frequencies, hold down both outside buttons until the green light begins to flash. This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada.
Page 150: Open Sunroof - Express Mode
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the keys in the ignition.
Page 151: Closing Sunroof - Express
Closing Sunroof - Express Press the switch forward and release, and the sunroof will close automatically from any position. The sunroof will close fully and stop automatically. This is called Express Close. During Express Close operation, any movement of the switch will stop the sunroof. Pinch Protect Feature This feature will detect an obstruction in the opening of the sunroof during Express Close operation.
Page 152: Wind Buffeting
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.
Page 153 The outlet(s) has/have a fused direct feed from the battery so it/they receive power whether the ignition is ON or OFF. All accessories connected to this/these outlet(s) should be removed or turned OFF when the vehicle is not in use to protect the battery against discharge.
Page 154: Cigar Lighter And Ash Receiver
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CIGAR LIGHTER AND ASH RECEIVER The removable ash receiver is located in the instrument panel cup holder tray. The cigar lighter is located on the instrument panel, above and to the left of the ash receiver. As a child safety precaution, the lighter only operates with the ignition switch ON.
Page 155: Cupholders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 CUPHOLDERS Front Instrument Panel Cupholders (40–20–40 Seats) — Automatic Transmission Your new Ram truck is equipped with two adjustable cupholders. The cupholder is opened by pulling on the cup holder door handle, on the front surface. Each opening in the cupholder is adjustable and will hold cups and mugs of various sizes.
Page 156 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cup Holder Door Handle Cup Holders Automatic Transmission...
Page 157: Front Instrument Panel Cupholders (Bucket Seats) - Automatic Transmission
Front Instrument Panel Cupholders (Bucket Seats) — Automatic Transmission If your new Ram truck is equipped with bucket seats there are three cup holders located on the front of the center console. Cup Holders Bucket Seat UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 Front Instrument Panel Cupholders —...
Page 158: Rear Cupholder - Quad Cab - If Equipped
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Cupholder — Quad Cab — If Equipped Quad Cab vehicles may be equipped with a rear cup- holder that consists of two cupwells for rear passenger convenience. Rear Cupholder — Mega Cab Mega Cab vehicles are equipped with rear cupholders located in the center armrest.
Page 159: Storage
STORAGE Center Storage Compartment (40–20–40 Seat) — If Equipped The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid. Push the button on the front of the armrest to raise the cover.
Page 160: Center Storage Compartment (Bucket Seats)- If Equipped
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
Page 161 storage area into separate compartments. Lift the lower handle on the front of the armrest, and raise the armrest for access to the lower storage bin. On Quad Cab and Mega Cab models the rear of the floor console offers a power outlet, a tip out bin and a rear air duct (Mega Cab Only).
Page 162: Storage And Seats (Quad Cab Models)
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage and Seats (Quad Cab Models) Located in the center of the front 40/20/40 seat cushion there is a storage compartment. Standard cab models also have storage behind the seat. The Quad Cab models provide additional storage under the rear seat.
Page 163 Push down on the front of the storage compartment handle and lift the storage compartment cover. Mega Cab Rear Storage Compartment Handle UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 The rear storage compartment can be divided into three separate compartments by using the divider doors inside the storage compartment.
Page 164: Plastic Grocery Bag Retainers (Mega Cab Models)
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Plastic Grocery Bag Retainers (Mega Cab Models) Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the rear seat. Grocery Bag Hooks REAR WINDOW FEATURES Electric Rear Window Defroster and Heated Side view Mirrors —...
Page 165: Power Sliding Rear Window-If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Power Sliding Rear Window—If Equipped The power sliding rear window switch is located on the instrument panel below the climate controls. Press the right side of the switch to open the glass and the left side of the switch to close the glass.
Page 166: Fold Flat Load Floor - If Equipped
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE FOLD FLAT LOAD FLOOR — IF EQUIPPED Quad Cab models with a 60/40 rear seat, may be equipped with a folding load floor. Quad Cab Rear 60/40 Seat WARNING! Do not operate the vehicle with loose items stored on the load floor.
Page 167 Unfolding the Load Floor 1. Lift the 60/40 seat cushion(s) to the upward position. Unfolding The Load Floor UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position. Load Floor In Open Position 3.
Page 168 168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Positioning the Load Floor for Storage Access Under the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load floor. 3.
Page 169: Pickup Box
PICKUP BOX Pickup Box Features The pickup box on your new Ram has many features designed for utility and convenience. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 NOTE: If you are installing a toolbox to the front of the pickup box, you must use Mopar available from your dealer.
Page 170: Slide-In Campers
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Care should always be exercised when operating a vehicle with unrestrained cargo. Vehicle speeds may need to be reduced. Severe turns or rough roads may cause shifting or bouncing of the cargo that may result in vehicle damage.
Page 171: Easy-Off Tailgate
EASY-OFF TAILGATE To simplify mounting of a camper unit with an overhang, the tailgate can be removed quickly. If the truck is a 3500 dual rear wheel model, unplug the tailgate wire harness from under the rear of the truck and pull the harness out of the cargo box access hole.
Page 172 172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! To avoid inhaling carbon monoxide, which is deadly, the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the overhanging camper compartment and be free of leaks. TAILGATE SUPPORT STRAP ATTACHMEN...
Page 173: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instruments And Controls ....177 Instrument Cluster ..... . 178 Instrument Cluster Description .
Page 174 174 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Radio — If Equipped ......197 Sales Code RAQ –...
Page 175 Noise Reduction ..... . 217 Operation Instructions - (CD Mode For CD Audio Play) ......217 Load/Eject Button (CD Mode For CD Audio Play) .
Page 176 176 UNDERSTANDING YOUR INSTRUMENT PANEL Satellite Antenna ..... . 230 Reception Quality ..... 230 Remote Sound System Controls —...
Page 177: Instruments And Controls
UNDERSTANDING YOUR INSTRUMENT PANEL 177 INSTRUMENTS AND CONTROLS...
Page 178: Instrument Cluster
178 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER...
Page 179: Instrument Cluster Description
INSTRUMENT CLUSTER DESCRIPTION 1. Check Gages This light illuminates when the Voltmeter, Engine Oil Pressure or Engine Coolant Temperature gages indicate a reading either too high or too low. Examine the gages carefully, and follow the instructions above for each indicated problem. NOTE: When the ignition switch is turned to OFF, the Fuel Gage, Voltmeter, Oil Pressure and Engine Coolant Temperature gages may not show accurate readings.
Page 180 180 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Do not operate the engine with the tachometer pointer at high rpm for extended periods. Engine damage may occur. 5. Airbag Indicator Light The indicator lights and remains lit for 6 to 8 seconds when the ignition is first turned on.
Page 181 NOTE: If the gauge pointer moves to either extreme of the gauge, the “Check Gages” indicator will illuminate and a single chime will sound. 10. Transfer Case Position (See page 273 for more information.) 11. TOW HAUL The TOW HAUL button is located at the end of the gear shift lever.
Page 182 182 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Do not leave your vehicle unattended with the engine running as you would not be able to react to the temperature indicator if the engine overheats. NOTE: Engine idle speed will automatically increase to 1000 rpm at elevated coolant temperatures to improve engine cooling.
Page 183 NOTE: There is also an engine hour function. This indicates the total number of hours the engine has been running. To display the engine hours perform the follow- ing: Place the ignition in RUN, but do not start the engine. With the odometer value displayed, hold the trip button down for a period of 6 seconds.
Page 184 184 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required.
Page 185 that the anti-lock portion of the brake system is not functioning and that service is required. See your autho- rized dealer immediately. The ABS light could also illuminate during loss of traction and remain illuminated until the brake pedal is pressed. 20.
Page 186 186 UNDERSTANDING YOUR INSTRUMENT PANEL 24. Water In Fuel Indicator Indicates there is water detected in the fuel filter. Refer to the Maintenance section, Drain- ing Fuel/Water Separator Filter, for water drain procedure. (See page 391 for more information.) 25. Low Washer Fluid Light This light comes on when the washer fluid level falls below approximately 1/4 full.
Page 187: Electronic Digital Clock
30. Low Fuel Warning Light Glows when the pointer is between “E” and 1/8 indication mark (approximately 15% of tank vol- ume) on the fuel gauge. When the fuel gauge pointer is on “E” (equivalent to Distance To Empty [DTE] = 0 on the overhead console if so equipped) there is reserve fuel capacity, which corresponds to approxi- mately 8% of tank volume.
Page 188: Clock Setting Procedure
188 UNDERSTANDING YOUR INSTRUMENT PANEL When the ignition switch is in the “OFF” position, or when the radio frequency is being displayed, time keep- ing is accurately maintained. On the RAQ radio the time button alternates the location of the time and frequency on the display. On the REF only one of the two, time or frequency is displayed at a time.
Page 189: Electrical Disturbances
Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal. AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs.
Page 190: Sales Code Ref - Am/Fm/Cd (Single Disc) Radio With Optional Satellite Radio And Hands Free Phone Capability
190 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL SATELLITE RADIO AND HANDS FREE PHONE CAPABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate. REF Radio Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
Page 191 Mode Button (Radio Mode) Press the mode button repeatedly to select between the CD player and Satellite Radio (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode.
Page 192 192 UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side Tune/ Audio control. 3. After the hours are adjusted, press the right side Tune/Audio control to set the minutes.
Page 193 Press the rotary TUNE control a fourth time and BAL will display. Turn the TUNE control to the right or left to adjust the sound level from the right or left side speakers. Press the rotary TUNE control a fifth time and FADE will display.
Page 194: Operation Instructions - Cd Mode
194 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - CD Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Inserting The Compact Disc (Single CD Player) Gently insert one CD into the CD player with the CD label facing up.
Page 195 SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal.
Page 196: Operation Instructions - Auxiliary Mode
196 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player, cassette player, or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
Page 197: Operating Instructions - Hands Free Phone - If Equipped
TIME Button (Auxiliary Mode) Press this button to change the display from elapsed playing time to time of day. The time of day will display for 5 seconds. RW/FF (Auxiliary Mode) No function. RND/SET Button (Auxiliary Mode) No function. Mode Button (Auxiliary Mode) Press the mode button repeatedly to select between the CD player and Satellite Radio (if equipped).
Page 198: Sales Code Raq - Am/Fm/Cd (6-Disc) Radio With Optional Satellite Radio, Hands Free Phone, And Vehicle Entertainment Systems (Ves) Capabilities
198 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, AND VEHICLE ENTERTAINMENT SYSTEMS (VES) CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate. RAQ Radio Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC...
Page 199 Mode Button (Radio Mode) Press the mode button repeatedly to select between the CD player, Satellite Radio, or Vehicle Entertainment System (VES) (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode.
Page 200 200 UNDERSTANDING YOUR INSTRUMENT PANEL Time Button Press the time button and the time of day will be displayed for 5 seconds. Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side Tune / Audio control.
Page 201 Press the rotary TUNE control a third time and TREBLE will display. Turn the TUNE control to the right or left to increase or decrease the Treble tones. Press the rotary TUNE control a fourth time and BAL- ANCE will display. Turn the TUNE control to the right or left to adjust the sound level from the right or left side speakers.
Page 202 202 UNDERSTANDING YOUR INSTRUMENT PANEL Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Rhythm_and_Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather By pressing the SEEK button when the PTY icon is Jazz displayed, the radio will be tuned to the next frequency News...
Page 203: Operation Instructions - (Cd Mode For Cd Audio Play)
You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET/DIR button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM.
Page 204 204 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! This CD player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. You may eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc.
Page 205: Load/Eject Button (Cd Mode For Cd Audio Play)
LOAD/EJECT Button (CD Mode for CD Audio Play) LOAD/ EJECT - Load Press the LOAD/ EJECT button and the push- button with the corresponding number where the CD is being loaded. The radio will display PLEASE WAIT and prompt when to INSERT DISC.
Page 206 206 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (CD MODE for CD Audio Play) Press this button to change the display from a large CD playing time display to a small CD playing time display. RW/FF (CD MODE for CD Audio Play) Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed.
Page 207: Notes On Playing Mp3 Files
Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restric- tions. Supported Media (Disc Types) The MP3 file recording media supported by the radio are CD-ROM, CD-R and CD-RW.
Page 208 208 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.mp3 exten- sion as MP3 files. Non-MP3 files named with the *.mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file.
Page 209: Operation Instructions
• Media - CD-RW media may take longer to load than CD-R media • Medium formats - Multisession discs may take longer to load than non-multisession discs • Number of files and folders - Loading times will increase with more files and folders To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs.
Page 210 210 UNDERSTANDING YOUR INSTRUMENT PANEL If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not removed, the radio will continue to play the non-removed CD. If the CD is removed and there are other CD’s in the radio, the radio will play the next CD after a 2 minute timeout.
Page 211: Sales Code Rak - Am/Fm/Cassette/Cd (6-Disc) Radio With Optional Satellite Radio, Hands Free Phone, Video, Mp3, And Wma Capabilities
Turn the TUNE control to display available folders or move through available folders. Press the TUNE control to select a folder. Buttons 1 - 6 (CD Mode for MP3 Play) Selects disc positions 1 - 6 for Play/Load/Eject. Operating Instructions - Hands Free Phone (If Equipped) Refer to Hands Free Phone in Section 3 of the Owner’s Manual.
Page 212: Operating Instructions - Radio Mode
212 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio.
Page 213 Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side Tune/ Audio control. 3. After the hours are adjusted, press the right side Tune/Audio control to set the minutes. The minutes will begin to blink.
Page 214 214 UNDERSTANDING YOUR INSTRUMENT PANEL Press the rotary TUNE control a third time and TREBLE will display. Turn the TUNE control to the right or left to increase or decrease the Treble tones. Press the rotary TUNE control a fourth time and BAL will display.
Page 215 Country Country Oldies Oldies Soft Soft Nostalgia Nostalgia Jazz Jazz Classical Classical Rhythm and Blues Rhythm_and_Blues Soft Rhythm and Blues Soft_R_&_B Foreign Language Foreign_Language Religious Music Religious_Music Religious Talk Religious_Talk Personality Personality Public Public College College Unassigned Weather Weather UNDERSTANDING YOUR INSTRUMENT PANEL 215 By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name.
Page 216: Operating Instructions - Tape Player
216 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Tape Player Insert the cassette with the exposed tape side toward the left and the mechanical action of the player will gently pull the cassette into the play position. NOTE: When subjected to extremely cold temperatures, the tape mechanism may require a few minutes to warm up for proper operation.
Page 217: Scan Button
Scan Button Press this button to play 10 seconds of each selection. Press the scan button a second time to cancel the feature. Changing Tape Direction If you wish to change the direction of tape travel (side being played), press Preset 6. The lighted arrow in the display window will show the new direction.
Page 218: Load/Eject Button (Cd Mode For Cd Audio Play)
218 UNDERSTANDING YOUR INSTRUMENT PANEL compact discs (CD-RW) compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks and WMA. Inserting Compact Disc(s) CAUTION! This CD player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism.
Page 219 Radio display will show LOADING DISC when the disc is loading and “READING DISC” when the radio is reading the disc. LOAD/EJT - Eject Press the LOAD/EJT button and the push- button with the corresponding number where the CD was loaded and the disc will unload and move to the entrance for easy removal.
Page 220: Notes On Playing Mp3 Files
220 UNDERSTANDING YOUR INSTRUMENT PANEL RND/PTY Button (Random Play Button) (CD MODE for CD Audio Play) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace.
Page 221 The radio uses the following limits for file systems: • Maximum number of directory levels: 15 • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator 3-character extension) •...
Page 222 222 UNDERSTANDING YOUR INSTRUMENT PANEL When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates.
Page 223: Operation Instructions
To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs. To create a single-session disc, enable the Disc at Once option before writing to the disc. Operation Instructions - (CD Mode for MP3 and WMA Audio Play) SEEK Button (CD Mode for MP3 and WMA Play) Pressing the right side of the SEEK button plays the next...
Page 224 224 UNDERSTANDING YOUR INSTRUMENT PANEL radio, the radio will remain in CD mode and display INSERT DISC” for 2 minutes. After 2 minutes, the radio will go to the previous tuner mode. INFO Button (CD Mode for MP3 Play) Press and INFO button while playing MP3 or WMA disc. The radio scrolls through the following TAG information: Song Title, Artist, File Name, and Folder Name (if avail- able).
Page 225: Sales Code Rec - Am/Fm/Cd (6-Disc) Radio With Navigation System
Operating Instructions - Hands Free Phone (If Equipped) Refer to “Hands-Free Phone” in Section 3 of the Owner’s Manual. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the “Satellite Radio” section of the Owner’s Manual. Operating Instructions - Video Entertainment System (VES) (If Equipped) Refer to separate “Video Entertainment System (VES) Guide.”...
Page 226: Operating Instructions - Satellite Radio (If Equipped)
226 UNDERSTANDING YOUR INSTRUMENT PANEL menus and instructions for selecting a variety of destina- tions and routes, AM/FM stereo radio and six-disc CD changer with MP3 capability. Mapping information for navigation is supplied on a DVD that is loaded into the unit. One map DVD covers all of North America.
Page 227: System Activation
System Activation NOTE: Your vehicle’s radio must be on and in satellite mode when the activation process takes place. To activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com. Please have the following informa- tion available when activating your system: 1.
Page 228: Selecting Satellite Mode In Ref, Raq, And Rak
228 UNDERSTANDING YOUR INSTRUMENT PANEL ESN/SID Access With RAQ and RAK Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and TIME buttons simultaneously for 3 seconds. All twelve ESN/SID num- bers will display. The radio will exit the ESN/SID mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed.
Page 229: Selecting A Channel
Selecting a Channel Press and release the SEEK or TUNE knob to search for the next channel. Press the top of the button to search up and the bottom of the button to search down. Holding the TUNE button causes the radio to bypass channels until the button is released.
Page 230: Pty Button Seek
230 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Pressing the SEEK or SCAN button, while performing a music type scan, will change the channel by one and stop the search. Pressing a pre-set memory button during a music type scan, will call up the memory channel and stop the search.
Page 231: Remote Sound System Controls - If Equipped
REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. Remote Sound System Controls UNDERSTANDING YOUR INSTRUMENT PANEL 231 The right hand control is a rocker type switch with a button in the center.
Page 232: Tape Player
232 UNDERSTANDING YOUR INSTRUMENT PANEL Tape Player Pressing the top of the switch once will go to the next selection on the cassette. Pressing the bottom of the switch once will go to the beginning of the current selection or to the beginning of the previous selection if it is within the first 5 seconds of the current selection.
Page 233: Compact Disc Maintenance
5. A loose tape should be corrected before use. To rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the required directions. Maintain your cassette tape player. The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played.
Page 234: Radio Operation And Cellular Phones
234 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged, oversized, or have theft protection encoding. Try a known good disc before considering disc player service. RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the operation of a cellular phone in your vehicle can cause erratic or noisy perfor- mance from your radio.
Page 235: Heater Only - If Equipped
Heater Only — If Equipped Manual Heating Controls UNDERSTANDING YOUR INSTRUMENT PANEL 235 The mode control (at the right of the control panel) can be set in any of the following positions: NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes.
Page 236 236 UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation Modes (Panel or Bi-Level) Select the recirculation modes when the outside air contains smoke or odors. This feature allows for recircu- lation of interior air only. Air flows through the panel outlets in this mode. Air flows through the panel only or through both the panel and floor vents depending on the selected mode (panel vs bi-level).
Page 237: Air Conditioning And Heating
Air Conditioning and Heating — If Equipped Air Conditioning And Heating Air Conditioning Operation To turn on the Air Conditioning, set the fan control at any speed and press the snowflake button located at the right of the control panel. Conditioned air will be directed through the UNDERSTANDING YOUR INSTRUMENT PANEL 237 outlets selected by the mode control.
Page 238 238 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots. Recirculation Modes (Panel or Bi-Level) Select the recirculation modes when the outside air contains smoke, odors, high humidity, or if rapid cooling is desired.
Page 239 Blower Control The rotary knob on the left of the control panel is the blower control. Turn the knob clockwise to one of the four positions to obtain the blower speed you desire. To turn the blower off, turn the knob to the far left posi- tion.
Page 240: Air Conditioning With Dual Zone Temperature Control - If Equipped
240 UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning with Dual Zone Temperature Control — If Equipped With the Dual Zone Temperature Control System, each front seat occupant can independently control the tem- perature of air coming from the outlets on their side of the vehicle.
Page 241 Recirculation Pushbutton Pushing the Recirculation button al- lows interior air to recirculate continu- ously in any position except defrost and defrost/floor mode for rapid cool down of the interior. See “Fast Cooldown” later in this section. Mode Control The mode control allows you to choose from several patterns of air distribution.
Page 242 242 UNDERSTANDING YOUR INSTRUMENT PANEL Outside air flows in equal proportions through the floor and defroster outlets. Defrost Outside air is primarily directed to the windshield through the defroster outlets located at the base of the windshield and side window demist outlets. NOTE: The air conditioning compressor operates in both Mix and Defrost or a blend of these modes, even if the A/C button has not been pressed.
Page 243 Dual Zone Temperature Control Dual Zone Temperature Control Use this control to regulate the temperature of the air inside the passenger compartment. This is accomplished by having separate temperature control slides for both UNDERSTANDING YOUR INSTRUMENT PANEL 243 the driver and front passenger. The blue area of the scale indicates cooler temperatures while the red area indicates warmer temperatures.
Page 244: Operating Tips
244 UNDERSTANDING YOUR INSTRUMENT PANEL conditioning system has been on. It is not an indication of a problem with the air conditioning system. Rear Air Duct—Mega Cab Only Mega Cab Rear Air Duct The rear seat will receive air flow in all modes except for Defrost.
Page 245 Window Fogging Windows will fog on the inside when the humidity inside the vehicle is high. This often occurs in mild or cool temperatures when it’s rainy or humid. In most cases turning on the Air-conditioning (pressing the snowflake button) will clear the fog. Adjust the temperature control, air direction and blower speed to maintain comfort.
Page 246 246 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: On models equipped with Diesel engines, the idle speed will automatically increase to 1000 rpm at elevated coolant temperatures to improve engine cooling. Your air conditioning system is also equipped with an automatic recirculation system. When the system senses a heavy load or high heat conditions, it may use partial Recirculation A/C mode to provide additional comfort.
Page 247: Operating Tips Chart
UNDERSTANDING YOUR INSTRUMENT PANEL 247 Operating Tips Chart...
Page 249: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures – Diesel Engines ..253 Manual Transmission – If Equipped ..253 Automatic Transmission – If Equipped ..253 Normal Starting Procedure —...
Page 250 250 STARTING AND OPERATING Manual Transmission ....274 Downshifting ......275 Four-Wheel- Drive Operation —...
Page 251 Radial-Ply Tires ..... . 307 Compact Spare Tire — If Equipped ..308 Limited Use Spare —...
Page 252 252 STARTING AND OPERATING Trailer Towing ......327 Common Towing Definitions ... . . 327 Trailer Hitch Classification .
Page 253: Starting Procedures - Diesel Engines
STARTING PROCEDURES – DIESEL ENGINES The starter should not be operated for more than 15- second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. WARNING! Be sure to turn off the engine if you want to rest or sleep in your car.
Page 254: Normal Starting Procedure - Engine Manifold Airtemperature Above 66°F (19°C)
254 STARTING AND OPERATING The Cummins Diesel engine is equipped with several features designed to assist cold weather starting and operation: • The engine block heater is a resistance heater installed in the water jacket of the engine just above and behind the oil filter.
Page 255: Starting Procedure - Engine Manifold Air
CAUTION! If WATER IN FUEL indicator light remains on DO NOT START engine before you drain water from the fuel filter to avoid engine damage. See Section 7 — Maintaining Your Vehicle, for water drain proce- dures. 4. Turn the ignition key to START and crank the engine. Do not press the accelerator during starting.
Page 256 256 STARTING AND OPERATING CAUTION! Do not crank engine for more than 15 seconds at a time or starter motor damage may result. Turn key to OFF and wait at least 2 minutes for starter to cool before repeating start procedure. •...
Page 257 attempting to start the engine. This can be accomplished by turning the ignition OFF for at least 5 seconds and then back ON after the WAIT TO START light has gone off, but before the engine is started. However, repeated cycling of the manifold heaters will result in damage to the heater elements or reduced battery voltage.
Page 258 258 STARTING AND OPERATING NOTE: When a diesel engine is allowed to run out of fuel or the fuel gels at low temperatures, air is pulled into the fuel system. You may try priming as described below. 1. Add a substantial quantity of fuel to the tank (5 to 10 gallons) or eliminate the gelled fuel condition.
Page 259: Starting Fluids
Starting Fluids WARNING! STARTING FLUIDS or flammable liquids are NEVER TO BE USED in the Cummins Diesel (see Warning label). Never pour diesel fuel, flammable liquid, starting fluids (ether) into the air cleaner canister, air intake piping, or turbocharger inlet in an attempt to start the vehicle.
Page 260: Cold Weather Precautions
260 STARTING AND OPERATING • Voltmeter Operation: • The voltmeter may show a gauge fluctuation if certain engine temperatures are below 66°F (19°C). This cycling operation is caused by the post-heat cycle of the intake manifold heater system. The number of cycles and the length of the cycling operation is controlled by the engine control mod- ule, this time will not exceed 150 seconds.
Page 261 NOTE: • Use of Climatized Diesel Fuel or Number 1 Diesel Fuel results in a noticeable decrease in fuel economy. • Climatized Diesel Fuel is a blend of Number 2 and Number 1 Diesel Fuels which reduces the temperature at which wax crystals form in fuel. NOTE: Refer to Fuel Requirements in this section for further details on fuel recommendations.
Page 262 262 STARTING AND OPERATING Block Heater Usage A. Temperatures below 0°F (-18°C) • Block Heater Required for 15W-40 • Block Heater Recommended for 5W-40 B. Temperatures below - 20°F (-29°C) • Block Heater Required for 5W-40 Winter Front Usage If a winter front or cold weather cover is to be used, a percentage of the total grille opening area must be left uncovered to provide sufficient air flow to the charge air cooler and automatic transmission oil cooler.
Page 263: Engine Idling - In Cold Weather
Engine Warm-Up Avoid full throttle operation when the engine is cold. When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up. NOTE: High-speed, no-load running of a cold engine can result in excessive white smoke and poor engine performance.
Page 264: Stopping The Engine
264 STARTING AND OPERATING speed will slowly increase to 1000 RPM after 2 minutes of idle, if the following conditions are met: • foot is off brake pedal and throttle pedal • automatic transmission is in Park (P) • vehicle speed is zero •...
Page 265: Engine Speed Control
Turbo- Driving Load charger Condition Temperature Stop and Empty Cool Stop and Medium Highway Medium Warm Speeds City Traffic Maximum GCWR Highway Maximum Speeds GCWR Uphill Maximum Grade GCWR Engine Speed Control Idle Time (min.) Before CAUTION! Engine Shutdown Prevent overspeeding the engine going down hill. Less than When descending steep grades, use a combination of gears and service brakes to control vehicle/engine...
Page 266: Cooling System Tips - Automatic Transmission
266 STARTING AND OPERATING Avoid Low Coolant Temperature Operation Continual operation at low coolant temperature below the normal range on the gauge (140°F/60°C) can be harmful to the engine. Low coolant temperature can cause incomplete combustion which allows carbon and varnish to form on piston rings and injector nozzles.
Page 267: Transmission Shifting
CAUTION! If oil pressure falls to less than normal readings, shut the engine off immediately. Failure to do so could result in immediate and severe engine damage. Do Not Operate The Engine With Failed Parts Practically all failures give some warning before the parts fail.
Page 268 268 STARTING AND OPERATING Gear Ranges DO NOT race the engine when shifting from Park or Neutral position into another gear range. “P” Park This gear position supplements the parking brake by locking the transmission. The engine can be started in this range.
Page 269 WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in re- verse.
Page 270 270 STARTING AND OPERATING “1” First Use this position for driving up very steep hills and for engine braking at low speeds 20 mph (32 km/h) or less when going downhill. To prevent excessive engine speed, do not exceed 25 mph (40 km/h) in this range. NOTE: Use caution when operating a heavily loaded vehicle in “2”...
Page 271 NOTE: If the vehicle is started in extremely cold tem- peratures, the transmission may not shift into Overdrive and will automatically select the most desirable gear for operation at this temperature. Normal operation will resume when the transmission fluid temperature has risen to a suitable level.
Page 272 272 STARTING AND OPERATING reduce the potential for transmission overheating or failure due to excessive shifting. When operating in “TOW HAUL” mode, 5th gear (if equipped) is disabled and 2-3 and 3-4 shift patterns are modified. Shifts into Overdrive (4th gear) are allowed during steady cruise (for improved fuel economy) and automatic closed- throttle downshifts to 3rd gear (for improved braking) will occur during steady braking.
Page 273 the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting into Overdrive when cold. This is normal. Pressing the “TOW/HAUL” button, when the transmis- sion is sufficiently warm, will demonstrate that the transmission is able to shift into and out of overdrive.
Page 274: Manual Transmission
274 STARTING AND OPERATING The alarm will continue for 3 minutes if the driver’s door is closed but none of the other conditions listed above are met. MANUAL TRANSMISSION WARNING! You or others could be injured if you leave the vehicle unattended without having the parking brake fully applied.
Page 275: Downshifting
toward you in one motion. Do not pull the lever sharply left as you may shift accidentally into 2nd gear and damage the transmission. You should use 1st gear when starting from a standing position if under heavy load or when pulling a trailer. To shift into Reverse, come to a complete stop.
Page 276: Four-Wheel- Drive Operation - If Equipped
FOUR-WHEEL- DRIVE OPERATION — IF EQUIPPED Four-Wheel-Drive Dodge Ram Trucks are equipped with either a Manually Shifted transfer case or an Electroni- cally Shifted transfer case. See the operating instructions for your transfer case, located within this section.
Page 277 The 4-wheel-drive light (4WD), located in the instrument cluster, alerts the driver that the vehicle is in 4-wheel drive and that the front and rear driveshafts are locked together. This light illuminates when the transfer case is shifted to either the 4H or 4L positions. There is no light for the 2H or N (Neutral) positions.
Page 278 278 STARTING AND OPERATING WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission position.
Page 279: Shifting Procedure - Manually Shifted Transfer Case
Shifting Procedure - Manually Shifted Transfer Case Manual Transfer Case Shifter 2H ⇔ 4H Shifting between 2H and 4H can be made with the vehicle stopped or in motion. If the vehicle is in motion, shifts can be made up to 55 mph (88 km/h). With the STARTING AND OPERATING 279 vehicle in motion, the transfer case will engage / disen- gage faster if you momentarily release the accelerator...
Page 280: Transfer Case Reminder Light
280 STARTING AND OPERATING NOTE: Shifting into or out of 4L is possible with the vehicle completely stopped, however difficulty may oc- cur due to the mating clutch teeth not being properly aligned. Several attempts may be required for clutch teeth alignment and shift completion to occur.
Page 281 This Electronically Shifted transfer case provides 4 mode positions: 2 (rear) wheel drive high range, 4 wheel drive high range, 4 wheel drive low range, and neutral. The Electronically Shifted transfer case is designed to be driven in the 2 wheel drive position (2WD) for normal street and highway conditions (dry hard surfaced roads).
Page 282 282 STARTING AND OPERATING Transfer Case Position Indicator Lights — Electronically Shifted Transfer Case Only Transfer case position indicator lights are located in the instrument cluster and indicate the current and desired transfer case selection. When you select a different trans- fer case position, the indicator lights will do the follow- ing: If All Shift Conditions are Met...
Page 283 WARNING! Always engage the parking brake when powering down the vehicle if the Service 4WD light is illuminated. Not engaging the parking brake may allow the vehicle to roll which may cause personal injury. NOTE: Do not attempt to make a shift while only the front or rear wheels are spinning.
Page 284 284 STARTING AND OPERATING WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission position.
Page 285: Shifting Procedure - Electronically Shifted Transfer Case
Shifting Procedure - Electronically Shifted Transfer Case Transfer Case Switch NOTE: If any of the requirements to select a new transfer case position have not been met, the transfer case will not shift.The indicator light for the previous position will remain ON and the newly selected position indicator STARTING AND OPERATING 285 light will continue to flash until all the requirements for the selected position have been met.
Page 286 286 STARTING AND OPERATING key must be in the ON position with the engine either RUNNING or OFF. This shift cannot be completed if the key is in the accessory position. NOTE: The 4x4 system will not allow shifts between 2WD/4HI if the front and/or rear wheels are spinning (no traction).
Page 287: Limited-Slip Differential - If Equipped
3. Rotate the transfer case control switch to the desired position. 4. After the desired position indicator light is ON (not flashing), shift transmission back into gear (release clutch on manual transmissions). NOTE: If steps 1 or 2 of either the Preferred or Alternate Procedure are not satisfied prior to attempting the shift then the desired position indicator light will flash con- tinuously while the original position indicator light is...
Page 288: Driving On Slippery Surfaces
288 STARTING AND OPERATING WARNING! On vehicles equipped with a limited-slip differen- tial, never run the engine with one rear wheel off the ground, since the vehicle may drive through the rear wheel remaining on the ground. You could lose control of the vehicle.
Page 289: Driving Off-Road
DRIVING OFF-ROAD Care should be taken when attempting to climb steep hills or driving diagonally across a hill or slope. If natural obstacles force you to travel diagonally up or down a hill, choose a mild angle and keep as little side tilt as possible. Keep the vehicle moving and make turns slowly and cautiously.
Page 290: Parking Brake
290 STARTING AND OPERATING PARKING BRAKE The foot operated parking brake is positioned below the lower left corner of the instrument panel. To release the parking brake, pull the parking brake release handle. NOTE: The instrument cluster red brake warning light will come on and flash to indicate that the parking brake is applied.
Page 291: Brake System
WARNING! • Always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury. Also be certain to leave an automatic transmission in Park, a manual transmission in Reverse or First gear. Failure to do so may allow the vehicle to roll and cause damage or injury.
Page 292: Brake Noise
292 STARTING AND OPERATING Brake Noise During normal operation of the brake system certain noises may be present from time to time. Occasional groan or squeal noises may occur during normal operation of the brake system which may not be indica- tive of a problem.
Page 293 WARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded. •...
Page 294: Power Steering
294 STARTING AND OPERATING ABS Warning Light The Anti-lock Brake System includes an amber warning light, located in the instrument cluster. When the light is illuminated, the Anti-lock Brake System is not function- ing. The system reverts to standard non-anti-lock brakes. WARNING! Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident.
Page 295: Tire Safety Information
WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolong operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and should be avoided when possible.
Page 296 296 STARTING AND OPERATING • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter P is absent from this tire size designation.
Page 297 Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%)
Page 298 298 STARTING AND OPERATING Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Page 299: Tire Identification Number (Tin)
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. = Department of Transportation —This symbol certifies that the tire is in compliance with the U.S.
Page 300: Tire Loading And Tire Pressure
300 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar. Tire Placard Location Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the:...
Page 301 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading...
Page 302 302 STARTING AND OPERATING passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (since 5 x 150 = 750, and 1400 – 750 = 650 lbs.) 5. Determine the combined weight of luggage and cargo being loaded on the vehicle.
Page 303 STARTING AND OPERATING 303...
Page 304: Tires - General Information
304 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 305: Tire Inflation Pressures
2. Economy— Improper inflation pressures can cause uneven wear pat- terns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation, also increases tire rolling resistance and results in higher fuel consumption. 3.
Page 306 306 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.”...
Page 307: Radial-Ply Tires
loading may be required for high-speed vehicle opera- tion. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. WARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail.
Page 308: Compact Spare Tire - If Equipped
308 STARTING AND OPERATING Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and rein- stalled at the first opportunity.
Page 309: Limited Use Spare - If Equipped
Limited Use Spare — If Equipped The limited use spare tire is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tire warning label located on the limited use spare tire and wheel assembly. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not.
Page 310: Tread Wear Indicators
310 STARTING AND OPERATING WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) for more than 30 seconds continuously when you are stuck, and don’t let anyone near a spinning wheel, no matter what the speed.
Page 311: Life Of Tire
Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure.
Page 312: Alignment And Balance
312 STARTING AND OPERATING WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspen- sion dimensions and performance characteristics, resulting in changes to steering, handling, and brak- ing of your vehicle.
Page 313: Supplemental Tire Pressure Information - If Equipped
Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. SUPPLEMENTAL TIRE PRESSURE INFORMATION – IF EQUIPPED A light load vehicle condition is defined as two passen- gers {150 lbs (68 kg) each} plus 200 lbs (91kg) of cargo.
Page 314 314 STARTING AND OPERATING These cautions apply to all chain traction devices, includ- ing link and cable (radial) chains. Tire chain use is permitted only on the rear tires of Ram 4X2 trucks. NOTE: The use of class “U” chains is permitted on the front and rear of 4X4, 2500 Ram Trucks with LT245/ 70R17E tires.
Page 315: Snow Tires
SNOW TIRES Snow tires should be of the same size and type construc- tion as the front tires. Consult the manufacturer of the snow tire to determine any maximum vehicle speed requirement associated with the tire. These tires should always be operated at the vehicle maximum capacity inflation pressures under any load condition.
Page 316: Dual Rear Wheels
316 STARTING AND OPERATING NOTE: On Canadian vehicles only, if your Ram truck is equipped with All-Season type tires on the front and ON/OFF Road type tires mounted on the rear, do not use a front to back rotation pattern. Instead, rotate your tires side to side at the recommended intervals.
Page 317: Engine Runaway
CAUTION! 3500 Dual Rear Tires have only one approved direc- tion of rotation. This is to accommodate the asym- metrical design (tread pattern) of the ON/OFF road tire and the use of Outline White Letter (OWL) tires. • When replacing a flat, the spare tire may have to be remounted on the rim or installed at a different location to maintain the correct placement of the tire on the wheel relative to the tire/wheel posi-...
Page 318: Fuel Requirements (Diesel Engines)
FUEL REQUIREMENTS (DIESEL ENGINES) Use good quality diesel fuel from a reputable supplier in your Dodge truck. For most year-round service, No. 2 diesel fuel meeting ASTM specification D-975 will pro- vide good performance. If the vehicle is exposed to extreme cold (below 20°F or -7°C), or is required to...
Page 319 NOTE: A maximum blend of 5% biodiesel may be used with your Cummins Diesel equipped Dodge Ram Truck. NOTE: In addition, commercially available fuel addi- tives are not necessary for the proper operation of your Cummins Diesel equipped Dodge Ram Truck.
Page 320: Adding Fuel (Diesel Engines)
320 STARTING AND OPERATING Fuel Properties - No. 1 - Diesel Carbon Residue - Less than.15% Flash Point - 100°F min. Density - 40-34 API gravity Cloud Point - (- 30F°) Active Sulfur Copper Strip Corrosion - #3 rating ADDING FUEL (DIESEL ENGINES) CAUTION! To avoid fuel spillage and overfilling, do not “top off”...
Page 321: Fuel Filler Cap (Gas Cap)
Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap).
Page 322: Bulk Fuel Storage
You may try priming as described below. However, if the engine will not start, refer to the fuel priming procedure in the Service Manual or have the vehicle towed to an authorized Dodge dealer. WARNING! Do not open the high pressure fuel system with the engine running.
Page 323: Vehicle Loading
4. Repeat the procedure if the engine does not start. CAUTION! Do not engage the starter motor for more than 15 seconds at a time. Allow two minutes between the cranking intervals. NOTE: The engine may run rough until the air is forced from all the fuel lines.
Page 324 324 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles. The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded. Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).
Page 325 then be determined separately to be sure that the load is properly distributed over front and rear axle. Weighing the vehicle may show that the GAWR of either the front or rear axles has been exceeded but the total load is within the specified GVWR.
Page 326 326 STARTING AND OPERATING NOTE: The weights shown in this chart are not Gross Vehicle Weight Rating (GVWR) 6500 LBS. necessarily the weights for your vehicle. Also, the amount of load added to both the front and rear axles can be computed after the vehicle has been weighed both in its curb weight condition, and in its loaded and ready for operation condition.
Page 327: Trailer Towing
TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer carefully re- view this information to tow your load as efficiently and safely as possible.
Page 328 328 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR.
Page 329 Weight-Distributing Hitch A weight-distributing system works by applying lever- age through spring (load) bars. They are typically used for heavier loads, to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axel(s). When used in accordance with the manufacturers’ directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.
Page 330 330 STARTING AND OPERATING Weight Distributing Hitch System Improper Adjustment of Weight Distributing System Fifth-Wheel Hitch A special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed. Connects a vehicle and fifth-wheel trailer with a coupling king pin.
Page 331: Trailer Hitch Classification
Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck. The coupling arm connects to the hitch mounted over the rear axle in the truck bed. Trailer Hitch Classification The rear bumper is intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alterations to the standard equipment.
Page 332: Trailer Towing Weights (Maximum Trailer Weight Ratings)
• http:// www.dodge.com/towing. • http:// www.dodge.ca (Canada). Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
Page 333: Towing Requirements
• The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle.
Page 334 334 STARTING AND OPERATING WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.
Page 335 2. GTW 3. GAWR 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing Requirements — Tires −...
Page 336 336 STARTING AND OPERATING actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. − Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg).
Page 337 STARTING AND OPERATING 337 NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 7- Pin Connector 4 - Pin Connector...
Page 338: Towing Tips
338 STARTING AND OPERATING Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. If using a manual transmission vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage.
Page 339: Trailer Towing Mirrors - If Equipped
− When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. − Use speed control in flat terrain and with light loads to maximize fuel efficiency. Towing Tips —...
Page 340 340 STARTING AND OPERATING Blindspot Mirror Trailer Towing Position...
Page 341: Snowplow
NOTE: Before installation of a snowplow it is highly recommended that the owner / installer obtain and follow the recommendations contained within the cur- rent Dodge BODY BUILDER’S GUIDE. See your dealer, installer or snowplow manufacture for this information. There are unique electrical systems that must be con- nected to properly assure operator safety and prevent overloading vehicle systems.
Page 342: Before Plowing
• Check that snowplow lighting is connected and func- tioning properly. Snowplow Prep Package Model Availability For Information about snowplow applications visit www.dodge.com or refer to the current Dodge Body Builders Guide. 1. The maximum number of occupants in the truck should not exceed two.
Page 343: Over The Road Operation With Snowplow Attached
of the plow. Front end tow-in should be checked and reset if necessary at the beginning and end of the snowplow season. This will help prevent uneven tire wear. The blade should be lowered whenever the vehicle is parked. Maintain and operate your vehicle and snowplow equip- ment following the recommendations provided by the specific snowplow manufacturer.
Page 344: General Maintenance
344 STARTING AND OPERATING NOTE: During snowplow usage on vehicles equipped with an overhead console module, the outside tempera- ture display will show higher temperatures than the outside ambient temperature. The higher displayed tem- perature is due to blocked or reduced airflow to the underhood ambient temperature sensor by the snow- plow.
Page 345: Recreational Towing (Behind Motorhome, Etc.)
RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Recreational Towing – 2 Wheel Drive Models Recreational towing 2 Wheel Drive is not allowed. Towing with the rear wheels on the ground can result in severe transmission damage. Recreational Towing – 4 Wheel Drive Models CAUTION! Failure to follow these requirements can cause se- vere damage to the transmission and/or transfer case.
Page 346 346 STARTING AND OPERATING CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in N (NEUTRAL) before recreational towing to prevent damage to internal parts. 1. Bring the vehicle to a complete stop. 2.
Page 347 CAUTION! Damage to the automatic transmission may occur if the transmission is shifted into P (PARK) with the transfer case in N (NEUTRAL) and the engine RUN- NING. With the transfer case in N (NEUTRAL) ensure that the engine is OFF prior to shifting the transmission into P (PARK) Returning to Normal Operation —...
Page 348 348 STARTING AND OPERATING CAUTION! • Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and damage the internal parts.
Page 349 6. Using the point of a ballpoint pen or similar object, depress the recessed transfer case Neutral (N) button for 4 seconds. 7. After shift is completed and the Neutral (N) light comes on release Neutral (N) button. 8. Start engine. 9.
Page 350 350 STARTING AND OPERATING NOTE: Flashing neutral (N) position indicator light indicates that shift requirements have not been met. CAUTION! Damage to the transmission may occur if the trans- mission is shifted into Park (P) with the transfer case in Neutral (N) and the engine RUNNING. With the transfer case in Neutral (N) ensure that the engine is OFF prior to shifting the transmission into Park (P).
Page 351 NOTE: Items 1 through 5 are requirements that must be met prior to depressing the Neutral (N) selection button, and must continue to be met until 1 second elapses and the shift has been completed. If any of these requirements (with the exception of 3 - key ON) are not met prior to depressing the Neutral (N) button or are no longer met during the 1 second time, then all of the mode position...
Page 352 352 STARTING AND OPERATING CAUTION! • Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and fluid loss will damage internal parts.
Page 353: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....354 Jacking And Tire Changing ....355 All Models .
Page 354: Hazard Warning Flasher
354 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Warning switch is mounted on the top of the steering column as shown in the illustration. Hazard Light Warning Switch To engage the Hazard Warning lights, depress the button on the top of the steering column.
Page 355: Jacking And Tire Changing
JACKING AND TIRE CHANGING WARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
Page 356: Jacking Instructions
356 WHAT TO DO IN EMERGENCIES WARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience, abrupt stopping, rapid accelera- tion, or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.
Page 357: Tire Changing Procedure
NOTE: The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. Tire Changing Procedure WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you.
Page 358 358 WHAT TO DO IN EMERGENCIES • Turn on the Hazard Warning Flasher. • Block both the front and rear of the wheel diagonally oppo- site the jacking position. For example, if the right front wheel is being changed, block the left rear wheel.
Page 359 1. Remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. 3. For 2500/3500 4x2 series trucks, when changing a front wheel, place the bottle jack under the frame rail behind the wheel.
Page 360 360 WHAT TO DO IN EMERGENCIES 4X2 Jacking...
Page 361 4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface. WHAT TO DO IN EMERGENCIES 361 WARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it.
Page 362 362 WHAT TO DO IN EMERGENCIES (SRW) models and 145 ft. lbs. (197 N·m) for 3500 dual rear wheel models. If in doubt about the correct tightness, have them checked with a torque wrench by your dealer or at a service station. WARNING! A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle.
Page 363 ratchet firmly. The hub cap should pop off. The wheel skins can now be removed. For the front hub cap on 3500 models use the blade on the end of the lug wrench to pry the caps off. The wheel skin can now be removed. CAUTION! Use a back and forth motion to remove the hub cap.
Page 364 364 WHAT TO DO IN EMERGENCIES 8-Stud — Dual Rear Wheels Dual wheels are flat mounted, center piloted. The lug nuts are a two piece assembly. When the tires are being rotated or replaced, clean these lug nuts and add 2 drops of oil at the interface between the hex and the washer.
Page 365 WHAT TO DO IN EMERGENCIES 365 These dual rear wheels should be tightened as follows: 1. Tighten the wheel nuts in the numbered sequence to a snug fit. 2. Retighten the wheel nuts in the same sequence to the torques listed in the table. Go through the sequence a second time to verify that specific torque has been achieved.
Page 366: Hoisting
366 WHAT TO DO IN EMERGENCIES wheel. The nuts should then be tightened to recom- mended torque. Tighten the nuts to final torque in increments. Progress around the bolt circle, tightening the nut opposite to the nut just previously tightened until final torque is achieved.
Page 367: Jump-Starting
JUMP-STARTING WARNING! To prevent personal injury or damage to clothing, do not allow battery fluid to contact eyes, skin or fabrics. Do not lean over a battery when connecting jumper cables or allow cable clamps to touch each other. Keep open flames or sparks away from battery vent holes.
Page 368 368 WHAT TO DO IN EMERGENCIES CAUTION! Use the Jump Start Procedure only when the charge indicator (if equipped) in both batteries is dark in the center. Do not attempt jump starting when either battery charge indicator (if equipped) is bright or yellow.
Page 369 2. Connect one end of the other jumper cable to negative (-) post of booster battery. Connect the other end of the jumper cable to a good ground on the engine block of the vehicle with the discharged battery. Make sure a good connection is made, free of dirt and grease.
Page 370: With Portable Starting Unit
370 WHAT TO DO IN EMERGENCIES WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle.
Page 371: Emergency Tow Hooks - If Equipped
not freeing the vehicle, may lead to transmission over- heating and failure. Allow the engine to idle with the transmission selector in NEUTRAL for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of transmis- sion failure during prolonged efforts to free a stuck vehicle.
Page 372: Towing A Disabled Vehicle
372 WHAT TO DO IN EMERGENCIES CAUTION! Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. TOWING A DISABLED VEHICLE Proper towing or lifting equipment is required to prevent damage to your vehicle.
Page 373: 2-Wheel- Drive Vehicles
2–Wheel- Drive Vehicles Provided that the transmission is operable, tow with the transmission in Neutral and the ignition key in the OFF position along with the front wheels raised and the rear wheels on the ground. Speed must not exceed 30 mph (50 km/h) and distance must not exceed 15 miles (25 km).
Page 375: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment ....378 5.9L HO Cummins Turbo Diesel ... 378 Onboard Diagnostic System (OBD II) .
Page 376 376 MAINTAINING YOUR VEHICLE Front Axle Universal Drive Joints And Pivot Bearings ......398 Body Lubrication .
Page 377 Bulb Replacement ..... . 433 Headlight (Halogen)/Front Park And Turn Lights ..... . 433 Fog Lights .
Page 378: Engine Compartment
378 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT 5.9L HO CUMMINS TURBO DIESEL...
Page 379: Onboard Diagnostic System (Obd Ii)
ONBOARD DIAGNOSTIC SYSTEM (OBD II) Vehicles equipped with California emissions controls have a sophisticated onboard diagnostic system called OBDII. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
Page 380: Engine Data Plate
380 MAINTAINING YOUR VEHICLE ENGINE DATA PLATE Use the information from the engine data plate when discussing service or sourcing parts for your engine. The engine data plate is located on the intake side of the breather cover. DEALER SERVICE Your dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner.
Page 381 CAUTION! To maintain your vehicle safely follow these guide- lines: • Watch your vehicle’s mileage and check your Mainte- nance Schedules regularly for required servicing. Ex- cessive wear or damage to certain vehicle components can result if required services are not performed. •...
Page 382 • Important: All maintenance other than that listed in this manual, as well as some procedures listed here, MUST be performed by your local Dodge Truck Dealer. Your authorized Dodge Dealer has been trained and has the necessary parts to maintain your...
Page 383: Maintenance Procedures
MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance. However, if a malfunction of these items does occur, it could adversely affect the engine or vehicle performance.
Page 384 384 MAINTAINING YOUR VEHICLE Never operate the engine with oil level below the “ADD” mark or above the upper “SAFE” mark. Change Engine Oil Road conditions as well as your kind of driving affect the interval at which your oil should be changed. Check the following to determine if any apply to you: •...
Page 385 If ANY of these apply to you, then change your engine oil at every interval shown in schedule B of the Mainte- nance Schedules section of this manual. If none of these apply to you, then change your engine oil at every interval shown on schedule A of the Mainte- nance Schedules section of this manual.
Page 386 386 MAINTAINING YOUR VEHICLE You may use synthetic engine oils provided the recom- mended oil quality requirements are met, and the recom- mended maintenance intervals for oil and filter changes are followed. Materials Added to Engine Oil The manufacture strongly recommends against the addi- tion of any additives (other than leak detection dyes or lube odorants) to the engine oil.
Page 387 Always check the condition of the used oil. This can give you an indication of some engine problems that might exist. • Thin, black oil indicates fuel dilution. • Milky discoloration indicates coolant dilution. Clean the area around the oil filter base. Remove the filter from the underside of the vehicle using a cap style oil filter wrench.
Page 388 388 MAINTAINING YOUR VEHICLE CAUTION! Overtightening may distort the threads or damage the filter element seal. Install the filter as specified by the filter manufacturer. Turn the filter 3/4 to one full turn after making contact with the gasket. Check the condition of the threads and sealing surface on the oil pan and drain plug.
Page 389: Drive Belt
Disposing Of Used Engine Oil And Filter Care should be taken in disposing of the used engine fluids from your vehicle. Used fluids, indiscriminately discarded, can present a problem to the environment. Contact your local dealer, service station, or governmen- tal agency for advice on recycling programs and where used fluids and filters can be safely discarded in your area.
Page 390 390 MAINTAINING YOUR VEHICLE Do not remove the top of the air filter housing to inspect the filter element on your diesel engine under normal operating conditions. The clear plastic housing on the Filter Minder™ allows you to view the amount of air pressure drop across the filter element.
Page 391: Draining Fuel/Water Separator Filter
A visual inspection of the air cleaner filter element is never recommended under normal circumstances. A badly restricted element may appear clean while a soiled element may be quite effective in filtering particles without restricting air flow. Rely on the Filter Minder™ to determine when a filter change is necessary.
Page 392 392 MAINTAINING YOUR VEHICLE CAUTION! Do not drain the fuel/water separator filter when the engine is running. NOTE: Care should be taken in disposing of used fluids from your vehicle. Used fluids, indiscriminately dis- carded, can present a problem to the environment. Con- tact your local authorized dealer, service station, or government agency for advice on recycling programs and for where used fluids and filters can be properly...
Page 393 Priming if the engine has run out of fuel 1. Add a substantial quantity of fuel to the tank 5 to 10 gallons (19L to 38L). 2. Crank the engine for 1 to 2 seconds. If the engine does not start, then release the key or starter button back to the RUN position (do not turn the key back to the OFF position).
Page 394: Maintenance Free Batteries
NOTE: A maximum blend of 5% biodiesel may be used with your Cummins Diesel equipped Dodge Ram Truck NOTE: As sufficient testing as not been completed, ethanol blends are not recommended or approved for use with your Cummins Diesel equipped Dodge Ram Truck.
Page 395 WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water.
Page 396: Air Conditioner Maintenance
396 MAINTAINING YOUR VEHICLE Battery Blanket Usage A battery loses 60% of its cranking power as the battery temperature decreases to 0°F (-18°). For the same de- crease in temperature, the engine requires twice as much power to crank at the same RPM. The use of 120 VAC powered battery blankets will greatly increase starting capability at low temperatures.
Page 397: Power Steering - Fluid Check
Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
Page 398: Steering Linkage - Inspection
398 MAINTAINING YOUR VEHICLE Steering Linkage — Inspection Whenever the vehicle is hoisted, all steering linkage joints should be inspected for evidence of damage. If seals are damaged, parts should be replaced to prevent leakage or contamination of the grease. Front Prop Shaft Lubrication Lubricate the front driveshaft grease fitting at each oil change listed in the appropriate Maintenance Schedule...
Page 399: Body Lubrication
Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, liftgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the appli- cation of any lubricant, the parts concerned should be wiped clean to remove dust and grit;...
Page 400: Exhaust System
400 MAINTAINING YOUR VEHICLE When refilling the washer fluid reservoir, take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades, this will help blade performance. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate.
Page 401: Cooling System
inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required. WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you.
Page 402 402 MAINTAINING YOUR VEHICLE accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Check the coolant recovery bottle tubing for brittle rub- ber, cracking, tears, cuts and tightness of the connection at the bottle and radiator.
Page 403 WARNING! Never add coolant to the radiator when the engine is overheated. Do not loosen or remove pressure cap to cool overheated engine! The coolant is under pres- sure and severe scalding could result. Cooling System — Drain, Flush and Refill At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled.
Page 404 404 MAINTAINING YOUR VEHICLE CAUTION! Mixing of coolants other than specified HOAT en- gine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOAT cool- ant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible.
Page 405 The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated.
Page 406 406 MAINTAINING YOUR VEHICLE Disposal Of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. Do not store ethylene glycol-based engine coolant in open containers or allow it to remain in puddles on the ground.
Page 407: Fan
Check the fan for cracks and bent or broken blades. If any of these conditions exist, you must replace the fan. Make sure it is securely mounted. NOTE: This service procedure must be performed by a trained service technician. Make arrangements with your authorized Dodge Truck Dealer for this inspection.
Page 408: Charge Air Cooler (Inter-Cooler)
408 MAINTAINING YOUR VEHICLE Charge Air Cooler (Inter-Cooler) The charge air cooler is positioned between the radiator and the air conditioner condenser. Air enters the engine through the air cleaner and passes through the turbo- charger where it is pressurized. This pressurized air rapidly reaches high temperature.
Page 409: Brake System
Brake System Power Disc Brakes (Front and Rear) Disc brakes do not require adjustment; however, several hard stops during the break-in period are recommended to seat the linings and wear off any foreign material. Brake Master Cylinder The fluid level of the master cylinder should be checked when performing under the hood service, or immedi- ately if the brake system warning lamp indicates system failure.
Page 410 410 MAINTAINING YOUR VEHICLE With disc brakes the fluid level can be expected to fall as the brake linings wear. However, an unexpected drop in fluid level may be caused by a leak and a system check should be conducted. Refer to Fluids, Lubricants and Genuine Parts for the correct Fluid type.
Page 411: Clutch Linkage
Brake Hoses Inspection should be performed whenever the brake system is serviced or at intervals specified. Inspect hy- draulic brake hoses for surface cracking, scuffing or worn spots. If there is any evidence of cracking, scuffing, or worn spots, the hose should be replaced immediately! Eventual deterioration of the hose can take place with possible burst failure.
Page 412: Transfer Case - If Equipped
412 MAINTAINING YOUR VEHICLE with water or subjected to severe service, follow the recommended change intervals in Maintenance Schedule “B” in Section 8 of this manual. Lubricant Selection Refer to Fluids, Lubricants and Genuine Parts for the correct lubricant type. NOTE: The presence of water in the gear lubricant will result in corrosion and possible failure of differential components.
Page 413: Automatic Transmission
Lubricant Selection for 6-Speed Manual Transmission — If Equipped If it becomes necessary to add fluid or change the fluid, be sure to use the same lubricant or equivalent. Refer to Fluids, Lubricants and Genuine Parts for the correct lubricant type. Automatic Transmission Fluid Level Check The fluid level should be checked when the engine is...
Page 414 Authorized Dodge Dealer or Service Center. It is important that the transmission be adjusted periodically, the fluid main- tained at the correct level, and that it be drained and...
Page 415: Front Wheel Bearings
The use of transmission sealers should be avoided, since they may adversely affect seals. Front Wheel Bearings Front wheel bearings for all Dodge Ram Trucks are sealed-for-life. They do not require greasing or seal replacement. In some instances, these bearings will “purge”...
Page 416: Selection Of Lubricating Grease
416 MAINTAINING YOUR VEHICLE • If a bearing assembly is accidentally separated when servicing the brake rotors, it should be replaced. Rear Wheel Bearings Clean and repack when brake linings are replaced or rotors resurfaced. Selection Of Lubricating Grease The National Lubricating Grease Institute (NLGI) has developed a symbol (Certification Mark) to aid the vehicle owner in the proper selection of grease for the lubrication of wheel bearings and chassis components.
Page 417: Noise Control System Required Maintenance & Warranty
Noise Control System Required Maintenance & Warranty For 3500 Two-Wheel Drive and Four-Wheel Drive mod- els over 10,000 lbs. (4 535 kg) Gross Vehicle Weight Rating. All vehicles built over 10,000 lbs. (4 535 kg) Gross Vehicle Weight Rating and manufactured for sale and use in the United States are required to comply with the Federal Government’s Exterior Noise Regulations.
Page 418 418 MAINTAINING YOUR VEHICLE or suspected. Proper maintenance of the entire vehicle will help the effectiveness of the noise control systems. Exhaust System Inspect the entire exhaust system for leaks and damaged parts. Devices such as hangers, clamps, and U-bolts should be tight and in good condition.
Page 419 • EXHAUST SYSTEM − Removal or rendering inoperative exhaust system components including the muffler or tailpipe. • ENGINE COOLING SYSTEM − Removal or rendering inoperative the fan clutch. − Removal of the fan shroud. Noise Emission Warranty The manufacturer warrants that this vehicle as manufac- tured by the manufacturer, was designed, built and equipped to conform at the time it left the manufacturer’s control with all applicable U.S.
Page 420 420 MAINTAINING YOUR VEHICLE Maintenance Log and Service Chart — 24 Valve Cummins Turbo Diesel Noise Systems Maintenance Chart and Service Log — Insert Month, Day, Year under column mileage closest to the mileage at which service was performed. MILES 7,500 KILOMETERS 12 000...
Page 421 Noise Systems Maintenance Chart and Service Log — Insert Month, Day, Year under column mileage closest to the mileage at which service was performed. MILES 67,500 75,000 KILOMETERS 108 000 120 000 Exhaust system- inspect Air cleaner assembly-inspect ODOMETER READING PERFORMED BY PERFORMED AT 82,500...
Page 422: Appearance Care And Protection From Corrosion
422 MAINTAINING YOUR VEHICLE Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
Page 423 • Use Mopar Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.
Page 424 424 MAINTAINING YOUR VEHICLE • Use Mopar touch up paint on scratches as soon as possible. Your dealer has touch up paint to match the color of your vehicle. Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion.
Page 425 WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Glass Surfaces All glass surfaces should be cleaned on a regular basis with Mopar Glass Cleaner or any commercial household- type glass cleaner.
Page 426: Fuses (Integrated Power Module)
426 MAINTAINING YOUR VEHICLE Replace the belts if they appear frayed or worn or if the buckles do not work properly. Dry with a soft tissue. FUSES (INTEGRATED POWER MODULE) An integrated Power Module is located in the engine compartment near the battery. This center contains car- tridge fuses and mini fuses.
Page 427 Cavity Cartridge Mini Description Fuse Fuse 20 Amp Power Outlet Console Yellow 20 Amp Cabin Compartment Yellow Node (CCN) Door Locks/Brake Trans- mission Shift Inter- lock (BTSI) 20 Amp Spare Yellow 20 Amp Spare Yellow 20 Amp Power Sunroof Yellow 10 Amp Occupant Classifica- tion Module (OCM)/...
Page 428 428 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 20 Amp Ignition Off Draw Yellow (IOD)-Cabin Com- partment Node (CCN)/Radio/Under Hood Lamp/Wireless Control Module (WCM)/Satellite Digi- tal Audio Receiver (SDARS)/Hands Free Module (HFM) 30 Amp Electric Brake Pink 25 Amp Power-Battery Natural RWAL/ABS Module...
Page 429 Cavity Cartridge Mini Description Fuse Fuse 10 Amp Engine Control Mod- ule (ECM)/Wireless Control Module (WCM)/HVC 20 Amp Subwoofer Amplifier Blue (SRT-10 Only) 10 Amp Power Mirror 20 Amp Brake Switch/Center Yellow High Mount Stop Lamp (CHMSL) 40 Amp Power Seats Green 10 Amp Power Run/Start-...
Page 430 430 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 25 Amp Audio_Amplifier Natural 15 Amp Spare Blue 20 Amp Power Outlet IP Yellow 10 Amp Sunroof/Seatbelt Ten- sioner 20 Amp Cigar Lighter Yellow 25 Amp Spare Natural 30 Amp Diesel PCM (Diesel Pink Only) Description...
Page 431: Vehicle Storage
VEHICLE STORAGE If you are storing your vehicle for more than 21 days, we recommend that you take the following steps to mini- mize the drain on your vehicle’s battery: • Disconnect the Ignition-Off Draw fuse (I.O.D.) fuse located in the Integrated Power Module, located in the engine compartment.
Page 432: Replacement Light Bulbs
432 MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS LIGHT BULBS — Inside Overhead Console Lights ....TS 212-2 Dome Light......7679 All of the inside bulbs are brass or glass wedge base.
Page 433: Bulb Replacement
BULB REPLACEMENT Headlight (Halogen)/Front Park and Turn Lights CAUTION! This is a halogen bulb. Avoid touching the glass with your fingers. Reduced bulb life will result. 1. Open the hood 2. Remove the two (2) bolts from the front of the head- light housing.
Page 434 434 MAINTAINING YOUR VEHICLE 3. Remove the plug from the inner fender well and remove the nut through the access hole. Inner Fender Plug Rear Headlight Housing Nut Access 4. Pull the housing out from the fender to allow room to disconnect the electrical connectors.
Page 435 NOTE: For easier removal, pull the headlight assembly straight forward, applying the greatest amount of force to the outer edge of the headlight assembly. Headlight Removal MAINTAINING YOUR VEHICLE Bulb Removal 5. Unlock and pull connector straight from the base of the headlight halogen bulb.
Page 436: Fog Lights
436 MAINTAINING YOUR VEHICLE 7. Remove housing from vehicle with headlight halogen bulb in housing. 8. Twist the headlight halogen bulb ⁄ turn and remove headlight bulb from the housing. 9. Replace headlight or side marker/turn signal/park light bulb. Do not touch the headlight halogen bulb. 10.
Page 437: Tail, Stop, Turn And Backup Lights
2. Pull bulb straight from the connector. 3. Reverse procedure for installation of bulbs and hous- ing. MAINTAINING YOUR VEHICLE Tail, Stop, Turn and Backup Lights 1. Remove the two (2) screws that pass through the bed sheetmetal. Removing the Two (2) Screws...
Page 438 438 MAINTAINING YOUR VEHICLE 2. Pull the housing straight out from the body, with a quick motion, to separate the housing from the body. If not pulled straight, locators may be damaged. Pulling Housing From Body 3. Rotate the bulb socket counterclockwise to remove from the housing.
Page 439 MAINTAINING YOUR VEHICLE 4. Pull bulb straight out of socket. 5. Reverse Procedure to install bulb and housing. Place the two raised blocks passed the body. Pulling Bulb From Socket Sliding Raised Blocks Past Body...
Page 440: Center High-Mounted Stoplight (Chmsl) With Cargo Light
440 MAINTAINING YOUR VEHICLE Center High-Mounted Stoplight (CHMSL) With Cargo Light 1. Remove the two (2) screws holding the housing/lens to the body as shown. 2. Separate the connector holding the housing and wir- ing harness to the body.
Page 441: Cab Top Clearance Lights - If Equipped
3. Turn desired bulb socket ⁄ turn and remove socket and bulb from housing. 4. Pull desired bulb straight from the socket. • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High Mount Stop Lamp MAINTAINING YOUR VEHICLE 5. Reverse procedure for installation of bulbs and hous- ing.
Page 442 442 MAINTAINING YOUR VEHICLE 2. Rotate the socket ⁄ turn and pull it from the light assembly. 3. Pull the bulb straight from it’s socket and replace.
Page 443: Tailgate Id Lights (Dual Rear Wheels) - If Equipped
Tailgate ID Lights (Dual Rear Wheels) — If Equipped 1. Remove the two screws and housing and access the bulb sockets from the rear. MAINTAINING YOUR VEHICLE 2. Turn socket ⁄ turn counterclockwise to access the bulb.
Page 444: Rear Light Bar Id Marker (Dual Rear Wheel) - If Equipped
444 MAINTAINING YOUR VEHICLE 3. Pull bulb straight out from socket. 4. Reverse procedure for installation of bulbs and hous- ing. Rear Light Bar ID Marker (Dual Rear Wheel) – If Equipped 1. Loosen the two screws and the housing to gain access to the bulb sockets.
Page 445: Side Marker Lights (Dual Rear Wheels)
3. Pull the bulb straight out from the socket. 4. Reverse procedure for installation of bulbs and hous- ing. Side Marker Lights (Dual Rear Wheels) 1. Push rearward on the side marker light assembly. 2. Pull the entire assembly from the fender. MAINTAINING YOUR VEHICLE 3.
Page 446: Fluids, Lubricants And Genuine Parts
446 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Engine Fuel Filter Fuel Selection Fluids, Lubricants and Genuine Parts Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) or equivalent. For the proper quality and SAE Grade oil for your engine, refer to the section Maintenance Procedures.
Page 447: Chassis
Chassis Component Automatic Transmission Transfer Case Manual Transmission Fluid G-56 Clutch Linkage Front and Rear Axle Fluid 2500/3500 Models Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar ATF+4, Automatic Transmission Fluid. Mopar ATF+4, Automatic Transmission Fluid. Mopar ATF+4, Automatic Transmission Fluid.
Page 449: Maintenance Schedules
MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..450 Maintenance Schedules — 5.9L Cummins Turbo Diesel ....... 450 Schedule “B”...
Page 450: Emission Control System Maintenance
450 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type in this section (Section 8) must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 451 • Off-road or desert operation. • Extensive operation at high engine speeds (greater than 2900 rpm) and loads (greater than 70% throttle). NOTE: Most vehicles are operated under the conditions listed for Schedule B . NOTE: If ANY of these apply to you then change your coolant every 101,250 miles (162 000 km) or 60 months, whichever comes first and follow schedule “B”...
Page 452 452 MAINTENANCE SCHEDULES Once a Month • Check tire pressure and look for unusual wear or damage. • Inspect the batteries and clean and tighten the termi- nals as required. • Check the fluid levels of coolant reservoir, brake master cylinder, and transmission and transfer case (if equipped), add as needed.
Page 453: Schedule "B" 453
Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Frequent short trips where the engine does not achieve full operating temperature (operating temperature de- fined as 190° F (66° C ) coolant temperature). •...
Page 454 454 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Check spare tire for proper pressure and correct stowage. Lubricate outer tie rod ends 2500/3500 (4X4) mod- els. Replace fuel filter element. Change rear axle fluid.
Page 455 Miles (Kilometers) Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Check spare tire for proper pressure and correct stowage. Lubricate outer tie rod ends 2500/3500 (4X4) mod- els. Inspect drive belt, replace as required. Replace fuel filter element.
Page 456 456 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4) models. Rotate tires. Check spare tire for proper pressure and correct stowage. Lubricate outer tie rod ends 2500/3500 (4X4). Inspect drive belt, replace as required. Replace fuel filter element.
Page 457 Miles (Kilometers) Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Flush and replace engine coolant at 60 months, if not replaced at 102,000 miles (163 000 km). Rotate tires. Check spare tire for proper pressure and correct stowage.
Page 458 458 SCHEDULE “B” Miles (Kilometers) Change 6-spd manual transmission (G-56) fluid 2500/3500. Inspect brake linings. Inspect and adjust parking brake if necessary. Drain and refill transfer case fluid (4X4). Drain and refill automatic transmission fluid and change main sump filter (545 RFE only). Drain and refill automatic transmission fluid.
Page 459 Miles (Kilometers) Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Check spare tire for proper pressure and correct stowage. Lubricate outer tie rod ends 2500/3500 (4X4) models. Inspect drive belt, replace as required. Change rear axle fluid.
Page 460 460 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Flush and replace engine coolant, if not replaced at 60 months. Rotate tires. Check spare tire for proper pressure and correct stowage.
Page 461 Miles (Kilometers) Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/ 3500, 4X4). Rotate tires. Check spare tire for proper pressure and cor- rect stowage. Flush and replace engine coolant at 120 months, if not replaced at 102,000 miles (163 000 km).
Page 462 462 SCHEDULE “B” Miles (Kilometers) Inspect front wheel bearings. Change rear axle fluid. Change front axle fluid (4X4). Change 6-spd manual transmission (G-56) fluid 2500/3500. Inspect brake linings. Inspect and adjust parking brake if necessary. Drain and refill automatic transmission fluid and change main sump and spin-on cooler return filter (if equipped) (545 RFE only).
Page 463: Schedule "A
Schedule “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Check spare tire for proper pressure and correct stow- age. Lubricate outer tie rod ends 2500/3500 (4X4) models. Check transfer case fluid level (4X4). Replace fuel filter element.
Page 464 464 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Check spare tire for proper pressure and correct stowage. Lubricate outer tie rod ends 2500/3500 (4X4) models. Check transfer case fluid level. Flush and replace engine coolant at 60 months, if not re- placed at 102,000 miles (163 000 km).
Page 465 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Check spare tire for proper pressure and correct stowage. Lubricate outer tie rod ends 2500/3500 (4X4) models. Flush and replace engine coolant, if not replaced at 60 mos. Check transfer case fluid level (4X4).
Page 466 466 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/ 3500, 4X4). Rotate tires. Check spare tire for proper pressure and cor- rect stowage. Lubricate outer tie rod ends 2500/3500 (4X4) models.
Page 467 Miles (Kilometers) [Months] Inspect front wheel bearings. Inspect brake linings. Inspect and adjust parking brake if necessary. Adjust valve lash clearance. Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts. 112,500 120,000 127,500 135,000...
Page 469: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ..... . . 470 Prepare For The Appointment ... . 470 Prepare A List .
Page 470: Suggestions For Obtaining Service For Your Vehicle
We want you to be happy with our products and services. Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to your selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 471 technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. •...
Page 472 472 IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni- cation Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
Page 473: Warranty Information (U.s. Vehicles Only)
WARRANTY INFORMATION (U.S. Vehicles Only) See the Warranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best.
Page 474: Publication Order Forms
474 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mas- tercard, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Page 475: Department Of Transportation Uniform
Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway Traffic Safety Adminis- tration.
Page 476: Temperature Grades
476 IF YOU NEED CONSUMER ASSISTANCE on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction perfor- mance. WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
Page 477 INDEX...
Page 478 478 INDEX Adding Fuel ......320 Adjustable Pedals ..... . . 132 Air Cleaner, Engine (Engine Air Cleaner Filter) .
Page 479 Axle Fluid ......412,447 Axle Lubrication (Axle Fluid) ....412 Ball Joints .
Page 480 480 INDEX CD (Compact Disc) Player ... . 190,198,211 Cellular Phone ......87 Center High Mounted Stop Light .
Page 481 Temperature Gauge ..... 181 Cruise Control (Speed Control) ....133 Cup Holder .
Page 482 482 INDEX Tow Hooks ......371 Towing ......372 Emission Control System Maintenance .
Page 483 Fold Flat Load Floor ..... 166 Four Wheel Drive ..... . . 276 Four-Way Hazard Flasher .
Page 484 484 INDEX Passing ......128 Switch ......124 Heated Mirrors .
Page 485 Keys ....... . . 12 Lane Change and Turn Signals ....127 Lap Belts .
Page 486 486 INDEX Turn Signal ....127,179,433,437 Warning (Instrument Cluster Description) ..179 Limited-Slip Differential ....287,412 Loading Vehicle .
Page 487 Noise Control Maintenance ......417 Tampering Prohibited ....418 Noise Emission Warranty .
Page 488 488 INDEX Phone, Cellular ......87 Phone, Hands-Free (UConnect™) ... . . 87 Pickup Box .
Page 489 Recreational Towing ..... . 345 Shifting into Transfer Case Neutral (N) ..345,348 Shifting out of Transfer Case Neutral (N) . . . 347,350 Refrigerant .
Page 490 490 INDEX Reclining ......111 Reclining Rear ......114 Security Alarm (Theft Alarm) .
Page 491 Steering Linkage ......398 Power ......294,397 Wheel Lock .
Page 492 492 INDEX Quality Grading ..... . . 475 Radial ......307 Replacement .
Page 493 Transmission Automatic ......267,413 Fluid ....... 447 Maintenance .
Page 494 494 INDEX Wheel Nut Torque ....361,365 Wind Buffeting ..... . . 31,152 Window Airbag (Side Curtain) .
Page 495 NOTES...
Page 496 NOTES...

Dodge 2007 DH Ram Owner's Manual

Quick Links

INTRODUCTION

Chapters

Related Manuals for Dodge 2007 DH Ram

Summary of Contents for Dodge 2007 DH Ram