Download Print this page

CTA PAD-SCGS Instruction Manual

Compact security gooseneck floor stand for 7-13 inch tablets

Advertisement

Quick Links

2. Installing the Wheels
2. Installing the Wheels
Place a spring washer over the screw
Place a spring washer over the screw
bolt on the wheel.
bolt on the wheel.
Package Contents:
Package Contents:
Instructions:
Instructions:
1.Attaching Foam Pad to Tablet Holder
1.Attaching Foam Pad to Tablet Holder
1mm Foam Pad
1mm Foam Pad
5mm
5mm
Foam
Foam
Pad
Pad
Select the appropriate foam pad according
Select the appropriate foam pad according
to the thickness of your tablet (or tablet in its
to the thickness of your tablet (or tablet in its
case), then press adhesive side into center
case), then press adhesive side into center
of the tablet holder.
of the tablet holder.
Section 1
Section 1
1. Insert key and set position
1.Insert key and unlock the
holder,TAKE OUT THE KEY
to unlock. Remove key,
then slide the arm to open
then slide holder open.
to a width according to your
2. Load tablet corner first
need.
into one end. Insert key
2. Insert key and lock the
and set to lock, then slide
holder,TAKE OUT THE KEY
holder shut until secure.
Remove key.
then install your device in
and slide the arm closed
to hold tightly.
Place the screw bolt from each wheel through the metal base, then place a nut cover
Place the screw bolt from each wheel through the metal base, then place a nut cover
over the top of each. Screw down clockwise by hand, then use wrench to tighten
over the top of each. Screw down clockwise by hand, then use wrench to tighten
further.
further.
SUPPORT@CTADIGITAL.COM
PAD-SCGS
PAD-SCGS
Use this table to determine the appropriate
Use this table to determine the appropriate
foam pad to use with your tablet.
foam pad to use with your tablet.
Note: sizes refer to total tablet size with or
Note: sizes refer to total tablet size with or
without a case.
without a case.
10mm
10mm
Foam
Foam
Pad
Pad
UNLOCK
UNLOCK
UNLOCK
UNLOCK
UNLOCK
UNLOCK
Screw Nut Cover
Screw Nut Cover
Spring
Spring
Washer
Washer
Metal
Metal
Base
Base
Wheel
Wheel
Tablet
Tablet
Foam Pad
Foam Pad
Thickness:
Thickness:
Thickness
Thickness
1mm
1mm
0.67-1.06in
0.67-1.06in
/
/
5mm
5mm
0.51-0.91in
0.51-0.91in
/
/
10mm
10mm
0.31-0.71in
0.31-0.71in
/
/
UNLOCK
UNLOCK
UNLOCK
UNLOCK
17-27m
17-27m
m
m
13-23m
13-23m
m
m
8-18mm
8-18mm

Advertisement

loading
Need help?

Need help?

Do you have a question about the PAD-SCGS and is the answer not in the manual?

Questions and answers

Summary of Contents for CTA PAD-SCGS

  • Page 1 PAD-SCGS PAD-SCGS Package Contents: Package Contents: Instructions: Instructions: 1.Attaching Foam Pad to Tablet Holder 1.Attaching Foam Pad to Tablet Holder Use this table to determine the appropriate Use this table to determine the appropriate foam pad to use with your tablet.
  • Page 2 3. Base Assembly and Connecting the Metal Cover: 3. Base Assembly and Connecting the Metal Cover: METAL CONNECTION METAL CONNECTION Pole Assembly and Pole Nut Pole Assembly and Pole Nut 1) Place the metal base pieces with the higher 1) Place the metal base pieces with the higher Cross Base Sections (2) Cross Base Sections (2) piece on top of the cross base.