Table of Contents
Advertisement
Quick Links
Please use this operation manual correctly on reading
well. Please keep it carefully to be able to read
immediately, when required.
TW-800
Contents
■General outline ...................................................... 1
■Main part and accessories .................................... 2
■Safety concerns ..................................................... 4
■Name and function of each part ........................... 8
■Installation ............................................................ 10
■Setting .................................................................. 15
■How to use ........................................................... 18
■Specification ........................................................ 20
■Dimensional drawing ........................................... 22
■After service and Warranty ................................. 26
Wireless Communication
Manual V1.20
Advertisement
Table of Contents
Related Manuals for Herutu TW-800R
Summary of Contents for Herutu TW-800R
-
Page 1: Table Of Contents
Wireless Communication TW-800 Manual V1.20 Contents Please use this operation manual correctly on reading ■General outline ............1 well. Please keep it carefully to be able to read ■Main part and accessories ........2 immediately, when required. ■Safety concerns ............. 4 ■Name and function of each part ...... -
Page 3: General Outline
TW-800 ■General outline TW-800 is constituted by a Transmitter[TW-800T] and a Receiver [TW-800R] Once the TW-800T is mounted on the Torque wrench a tool of others with Limit switch (LS), the tightening completion signal of Torque wrench can be transmitted to each series of our TWF-800R. <Feature>... -
Page 4: Main Part And Accessories
TW-800 ■Main part and accessories Transmitter TW-800T Screw for fitiing M4×L5×4 Coin battery CR 2032×1 TW-800T ×1 (Screw for fitting a mainpart, Limit switch) Fitting plate×1 Receiver TW-800R TW-800R ×1 (Dipole antenna for ANT2 is set at shipment) ※ANT2 is fixed by resin before shipment by regulation of FCC/IC in an applicable country. - Page 5 TW-800 Onerous option ・AC Adapter ADB24050-C(With connecting cable 3m) Cable approx 1.5m Cable approx 2m ・External antenna MB-13F(With magnet base/Coaxial cable approx 1.5m) Antenna approx 22.5cm Coaxial cable approx 1.5m ※ANT2 is fixed by resin before shipment by regulation of FCC/IC in an applicable country.
-
Page 6: Safety Concerns
TW-800 ■Safety concerns Safety concerns (Be sure to read) To prevent human injury of user or damage in property from occurring, be sure to observe the precautions shown below. ■ The degree in safety hazard and damage generated by the wrong usage while ignoring the descriptions is classified by the following displays. - Page 7 TW-800 Warning ■For handling the power source: Be sure to observe the following precautions to prevent the AC adapter and Power cord from being heated, damaged, or ignited. ●Do not approximate the AC adapter and Power cord to a fire, or do not put them into a fire. The AC adapter and Power cord can be broken or ignited, resulting in an accident.
- Page 8 TW-800 ■Caution for wireless Law ○Radio device in this product has been certified by the Radio Law. It does not needs a license of radio stations according to using this product. ○Do not use it close to a person with a cardiac pacemaker. Electromagnetic interference may affect it, putting his/her life at risk.
- Page 9 TW-800 ■FCC/IC Warning (TW-800T,TW-800R) Information about FCC Standard. FCC CAUTION Change or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interface, and (2) This device must accept any interface received, including interface that may cause undesired operation: Information about FCC Standard and IC standard.
-
Page 10: Name And Function Of Each Part
TW-800 ■Name and function of each part ●Transmitter TW-800T Label is changed for FCC/IC. 1.Seat Seat is for setting torque wrench and plier wrench and so on. 2.Hole of bracket The hole is for mounting the base of torque wrench of LS type and seat 3.Case Case for main body. - Page 11 TW-800 ●Receiver TW-800R This label is added For FCC/IC. 1.Power switch For power ON and OFF 2.Terminal block of Terminal block for power source of DC24V(M3) power source 3.DIP Switch For setting DIP switch(6 selection) 4.Output terminal block Photo-mos relay output terminal block(M3) 5.RX light switch:Green Led lights at receiving the signal from transmitter normally.
-
Page 12: Installation
TW-800 ■Installation <Installation the transmitter to torque wrench> To install the seat Fix the Seat with four fixing screws. For the application with heavy oil mist, fill up the caulking agent between Wrench seat and Seat and also between Wrench shaft and Wrench seat to protect the internal board. Apply the screw locking agent ×4 onto the 2 to 3 threads of screw... - Page 13 TW-800 <The attention and the check method on limit switch attachment> When the lever working range of a torque wrench is small, a limit switch cannot be struck and a transmitter may not send. In limit switch attachment, be careful enough and carry out. <Input Judgment time for transmitter>...
- Page 14 TW-800 The antenna of a receiver should install so that there is no obstacle in the circumference of an antenna. Receiver has 2 antennas and it is diversity type. Both antennas should install that there is no obstacle in the circumference of an antenna.
- Page 15 TW-800 Please do not set the following installation. It is touched antenna with sequence It is parallel with sequence box and box. antenna It is installed bear power line. Each antennae are in touch.
- Page 16 TW-800 ・This product serves as a minus (-) ground. In the case of the place which is fixed this receiver is steel such as an operator control panel and a pillar of a production line, please fix this receiver after confirming minus grounding or plus grounding.
-
Page 17: Setting
TW-800 ■Setting It needs “pairing” a transmitter and a receiver before using. Transmitter and receiver communicate by recognizing the other party's recognition signal by pairing. ●Pairing (Registration) 1. Power Switch is turned on pushing the lighting switch for paring of a receiver. To enter “Pairing mode”... - Page 18 TW-800 ●Setting of receiver You can set “relay output time”, “Double count protect time”, “Behavior of buzzer” by six dipswitch. Please set by your operation. ◆Buzzer ON/OFF DIPSW Buzzer does not sound Buzzer sounds ◆Relay output time (4 kinds) DIPSW 50ms 200ms 400ms...
- Page 19 TW-800 ◆Caution While the receiver output relay output or while receiver is in double count protect time, receiver transmit the busy signal to transmitter. Then receiver doesn’t move. When the transmitter receives the busy signal, the Green LED of transmitter flashes 3 times. According to setting relay output time and double count protect time, a difference is made for a transmitting intervals.
-
Page 20: How To Use
TW-800 ■How to use 1. Power switch of receiver is turned on. Please confirm the LED situation as turning off. When the LED for receiving turns on, the transmitter is not registered by pairing. Please make a pairing with transmitter. LED for receiving (Green) (Lighting switch for pairing) LED(Green &... - Page 21 TW-800 ●TEST SWITCH There is a test switch for checking the battery and communication. When the transmitter transmit the signal by test switch not limit switch, receiver doesn’t output relay output. But LED of receiver only turns on. Also transmitter make a checking the battery at pushing the test switch. You can know the battery situation by transmitter LED and Receiver LED TEST SWITCH is combination with Pairing switch.
-
Page 22: Specification
TW-800 ■Specification ●TW-800 common specification Items Specification Standard 2.4GHz Small electric power data communication system Emission designation Frequency band 2,403MHz-2,476MHz Channel 76CH Modulation way GFSK Communication way Simplex Power of antenna 2.1mW ●Transmitter TW-800T Items Specification Limit switch*1 point Input Test switch* 1point Display LED *1 point(Red/Green... - Page 23 TW-800 ●Receiver TW-800R Items Specification Contact output* 1point Contact mechanism MOS-FET/1a Output Terminal block:M3(2P) Rated load voltage AC/DC30V per point Rated load current 0.5A per point LED for receiving(Green) * 1point Display (Combination lighting switch for pairing) Power LED(Red) * 1point DC24V±20%(DC19-28V) Power source Terminal block: M3(2P)
-
Page 24: Dimensional Drawing
TW-800 ■Dimensional drawing ●Transmitter TW-800T... - Page 25 TW-800 ●Receiver TW-800R...
- Page 26 TW-800 ■Before thinking failure TW-800(Transmitter) Phenomenon A cause and measure Battery level is low. →Please change a new battery (CR2032). Limit switch is separated from transmitter. No transmitting →Please check that the connector and limit switch connector (Not lighting LED Red or Green) of a transmitter circuit board have connected firmly.
- Page 27 TW-800 TW-800R(Receiver) Phenomenon Cause and measure Power is not input. Power LED doesn’t turn on →Please input stable power source DC24V. It has not done “Pairing” (No registration) Not receiving the signal from transmitter. →Please do “Pairing” with receiver. Ref P14 Buzzer setting is OFF.
-
Page 28: After Service And Warranty
TW-800 ■After service and Warranty If something is wrong If you should find anything wrong with the machine when using it under normal conditions, check the following items and contact the outlet store through which you purchased the product or our Sales Office. Product name / Serial No. - Page 29 TW-800 7. Replacement of consumables and limited-life items (including batteries). Consumables and limited-life items include, but not limited to: (1) Switches (limit switches, pushbutton switches, or the like) (2) Battery cells or batteries (dry batteries, button batteries, or the like) (3) Other items subject to consumption or limitation of life caused by use.
- Page 33 HERUTU ELECTRONICS CORPORATION 〒433-8103 62-1Toyooka-cho, Kita-ku, Hamamatsu-shi, Shizuoka-ken （Sales dept）TEL.+81-053- 438－3555 FAX. +81-53- 438－3411 http://www.herutu.co.jp E-mail webmaster@herutu.co.jp...
Need help?
Do you have a question about the TW-800R and is the answer not in the manual?
Questions and answers