Kraus Oletto KPF- 2620 Manual

Introduction

Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance, or have any problems with your product:

DO NOT RETURN TO STORE
Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com
Have the model number available, and retain a copy of your receipt with purchase date for reference.
If for any reason this product does not meet your expectations, please be sure to repack this product in the original box and packaging material to avoid damage during transit.

Tools you will need:

Wrench	Phillips Screwdriver	Pipe Tape	Silicone Sealant (optional)	Safety Goggles

Care & Maintenance
* To keep the product clean & shining, follow the steps below:

1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
   * This installation manual is subject to change without further notice.

Diagram and Parts List

1. Spray Head
2. Faucet Body
3. Escutcheon
4. Gasket
5. Easy Install Assembly
6. Weight

Installer Tip:
Shut off main water supply before installing new faucet

Setting Up

1. 1. Installing the easy install assembly (Without escutcheon)
      Shut off the water supply. Remove the old faucet. Clean the mounting surface. Check for the proper thickness of the sink. Insert the base (a) into sink. If your model does have a escutcheon, skip to step 1 b.
      NOTE: "Front" on the base (a) must face the front of the sink. The two mounting plates (b) on the base (a) must be loose and movable during the installation of the base (a).
      
   2. Installing the easy install assembly (With escutcheon)
      Place the escutcheon (C) and the gasket (D) on the sink. Insert the base (a) into escutcheon (C). Note: "Front" on the base (a) must face the front of the sink. The two mounting plates (b) on the base (a) must be loose and movable during the installation of the base (a). If the sink is uneven, use silicone under the gasket (D).
      
2. Installing the easy install assembly
   Press the base (a) and escutcheon (C) so that they can not move, then turn the screws with the provided hex wrench (J, HEX: 6.0mm) clockwise, as shown Fig 1. When the mounting plates (b) make contact with the sink (1), continue to turn the screw with the provided hex wrench (J, HEX: 6.0mm) clockwise, as shown Fig 2, until the base (a) is completely tightened and secured, as shown Fig.4.
   
3. Installing the faucet
   Insert the hose (1)、supply lines (2) and quick connect hose (3) one by one through the hole of the base (a). Carefully insert the hoses into the base. Place the faucet assembly onto the base (a) as shown in the above figure. Secure the faucet assembly (B) by tightening the set screw with the provided hex wrench (I, Hex: 2.5 mm).
   
4. Securing the faucet assembly
   Install the weight clip (G) at the point of the hose marking "weight here". Insert the weight (F) onto the weight clip (G) by sliding it down onto the weight clip (G).
   
5. Connect waterlines to main valve
   Attach waterlines to angle stops and tighten until snug. Turn on angle stops and check for leaks (DO NOT TURN FAUCET ON).
   NOTE: Please make sure filter washers are installed before connecting to the main valve
   
6. Flush faucet
   Pull the hose assembly out of the spout and remove the spray head (A) by unscrewing it from the hose in a counterclockwise direction. Be sure to hold the end of the hose down into the sink and turn the faucet on to the warm position where it mixes hot and cold water. Flush the water lines for one minute. This flushes away any debris that Acould cause damage to internal parts. Check for leaks. Re-tighten any connections if necessary, but do not overtighten. Reinstall the spray head (A) by hand tightening it back onto the sprayer hose.
   After installation is completed, turn on the hot and cold water supplies. Check for leaks.
   NOTE : Please make sure washer is installed attaching sprayer to hose.
   

*Denotes faucet component color options:
CH- Polished Chrome; SFS - Spot Free Stainless Steel; BB - Brushed Brass;
MB - Matte Black; SFACB - Spot Free Antique Champagne Bronze;
Gray hose with Spot-Free Stainless connector (GRSFS);
Gray hose with Chrome connector (GRCH);
Black hose with Brushed Brass connector (BLBB);
Black hose with Matte Black connector (BLMB);
Black hose with Spot-Free Antique Champagne Bronze (BLSFACB);
GR - Grey;
BL - Black

Troubleshooting

If you have followed the instructions carefully and your faucet still does not work properly, take the following coorective steps:

Register Your Kraus Product
Activate Your Warranty
Access Premium Customer Support
Get Product Information
REGISTER TODAY
http://www.kraususa.com/registration

www.kraususa.com