Page 2
DISCLAIMER Integrated Device Technology, Inc. reserves the right to make changes to its products or specifications at any time, without notice, in order to improve design or performance and to supply the best possible product. IDT does not assume any responsibility for use of any circuitry described other than the circuitry embodied in an IDT product. The Company makes no representations that circuitry described herein is free from patent infringement or other rights of third parties which may result from its use.
Table of Contents ® Description of the EBP0602Q SATA 6G Evaluation Board Notes Introduction ............................. 1-1 Board Features ..........................1-1 Hardware ..........................1-1 Revision History ..........................1-1 Installation of the EBP0602Q (SATA 6G) Evaluation Board EBP0602Q Installation........................2-1 Hardware Description ........................2-1 Power Sources..........................
Page 4
IDT Table of Contents Notes 89EBP0602Q SATA 6G Evaluation Board December 8, 2010...
Chapter 1 Description of the EBP0602Q SATA 6G Evaluation Board ® Introduction Notes The 89HP0602Q 6.25Gbps Signal Repeater (also referred to as P0602Q in this manual) is a member of the IDT Signal Integrity Products family. It is a 2-channel repeater that supports 1 bidirectional SATA 6G lane.
Page 10
IDT Description of the EBP0602Q SATA 6G Evaluation Board Notes 89EBP0602Q SATA 6G Evaluation Board 1 - 2 December 8, 2010...
Chapter 2 Installation of the EBP0602Q (SATA 6G) Evaluation Board ® EBP0602Q Installation Notes This chapter discusses the steps required to configure and install the EBP0602Q evaluation board. All available DIP switches and jumper configurations are explained in detail. The primary installation steps are: 1.
IDT Installation of the EBP0602Q (SATA 6G) Evaluation Board External Power Source Notes External power is supplied to the EBP0602Q board through a 15-pin SATA power connector (J8) or USB connector (J27) via Header W3. The external power supply provides +5V to the EBP0602Q as described in Table 2.2.
IDT Installation of the EBP0602Q (SATA 6G) Evaluation Board LEDs Notes There are LED indicators on the EBP0602Q which convey status feedback. A description of each is provided in Table 2.4. Location Color Definition Green 5V Power Indicator Green 1.2V Power Indicator Table 2.4 LED Indicators SATA Connectors The P0602Q repeater has no special orientation requirements with respect to the host controller or disk...
Page 14
IDT Installation of the EBP0602Q (SATA 6G) Evaluation Board Notes Figure 2.2 EBP0602Q Board Bottom Figure 89EBP0602Q SATA 6G Evaluation Board 2 - 4 December 8, 2010...
Chapter 3 Schematics ® Schematics Notes 89EBP0602Q SATA 6G Evaluation Board 3 - 1 December 8, 2010...
Page 16
REVISIONS REVISIONS DESCRIPTION DESCRIPTION DATE DATE CHANGE BY CHANGE BY INITIAL RELEASE INITIAL RELEASE 2010-07-18 2010-07-18 K. LEUNG K. LEUNG IDT 89HP0602Q SATA EVALUATION BOARDS IDT 89HP0602Q SATA EVALUATION BOARDS TABLE OF CONTENTS TABLE OF CONTENTS 89HP0602Q, POWER.....2 89HP0602Q, POWER.....2 89HP0602Q, SATA CONNECTORS...3 89HP0602Q, SATA CONNECTORS...3 TITLE...
Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use o any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products.
Need help?
Do you have a question about the IDT 89EBP0602Q and is the answer not in the manual?
Questions and answers