Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for HPE Aruba Networking 600R Series
Summary of Contents for HPE Aruba Networking 600R Series
- Page 1 HPE Aruba Networking 600R Series Remote Access Points Installation Guide...
- Page 2 Hewlett Packard Enterprise Company. To obtain such source code, please check if the code is available in the HPE Software Center at https://myenterpriselicense.hpe.com/cwp-ui/software but, if not, send a written request for specific software version and product for which you want the open source code.
-
Page 3: Table Of Contents
Regulatory Information Safety and Regulatory Compliance Brazil Canada EU and UK Regulatory Conformity European Union and United Kingdom Japan Korean México Нормативные требования Евhразийского Экономического Союза Ukraine Taiwan UKCA United States Medical HPE Aruba Networking 600R Series Remote Access Points... -
Page 4: About This Guide
About This Guide About This Guide This document describes the hardware features of the HPE Aruba Networking 600R Series Remote Access Points. It provides a detailed overview of the physical and performance characteristics of each access point model and explains how to install the access point. -
Page 5: Hardware Overview
(For AP-605R bundle only) AP-605CM12 LTE CAT12 cellular module (pre-installed) x 1 To simplify the ordering, HPE Aruba Networking offers the AP-605R bundle that combines an AP-605R access point, a power adapter (with power cord) and a AP-605CM12 LTE CAT12 cellular module (pre-installed) -
Page 6: System Status Led
Access point powered off Green - blinking Access point booting, not ready Green - solid Access point ready, fully functional System error condition or thermal shutdown engaged - Immediate attention required HPE Aruba Networking 600R Series Remote Access Points |... -
Page 7: Led Display Settings
The LCD screen is located on the front panel of the access point. The LCD button is located on the right side of the screen and used to operate the LCD screen: When booted up, the LCD will display the home screen, which is HPE Aruba Networking logo by default, but it is configurable by the system management software. - Page 8 "Wi-Fi failed to connect to network. Display Running Status after 5 s" "Mesh failed to connect to network. Display Running Status after 5 s" "Cellular failed to connect to network. Display Running Status after 5 s" HPE Aruba Networking 600R Series Remote Access Points |...
- Page 9 "Cellular failed to obtain IP address. Display Running Status after 5 s" Figure 8 Ethernet Failed to Obtain IP Address Connecting to Central When the AP is connecting to Central, the LCD screen will display "Connecting to Central..." HPE Aruba Networking 600R Series Remote Access Points...
- Page 10 Network Information Page Ethernet Port Information Page WLAN Information Page USB Interface Information Page Modem Information Page System Information Page In this page, the LCD screen will display the following information: HPE Aruba Networking 600R Series Remote Access Points |...
- Page 11 In this page, the LCD screen will display the following information: Figure 14 Ethernet Port Information Page Speed (10/100/1000/2500/5000 Mbps) Uplink port or downlink port (indicated by up arrow icon, or down arrow icon on the left side of each port icon) HPE Aruba Networking 600R Series Remote Access Points...
- Page 12 If this is an modem plugged in the USB interface, but it is not used as uplink port, the LCD screen will display "Modem link is not used". If the Modem link is up, the LCD screen will display the related information in two page. HPE Aruba Networking 600R Series Remote Access Points |...
- Page 13 SIM card status: "SIM_ABSENT" or "SIM_READY" On the top right corner of the LCD screen, it displays an icon to show the link status (up or down), network mode (3G or 4G), and signal strength. HPE Aruba Networking 600R Series Remote Access Points...
-
Page 14: Back And Side View
To reset during power up, hold the reset button while the access point is powering up. The system status LED will flash again within 15 seconds indicating that the reset is completed. The access point will now continue to boot with the factory default settings. HPE Aruba Networking 600R Series Remote Access Points |... -
Page 15: Micro-B Console Port
To create a console connection to the access point, follow these steps: 1. Connect the console port on the access point to the serial port on the computer using the proprietary HPE Aruba Networking AP-CBL-SERU cable or AP-MOD-SERU module, which need to be purchased separately. -
Page 16: Usb Interface
Once the AP has established a connection with its management platform, the BLE radio state is updated to match what’s configured there. This state is maintained if the AP is power- cycled or rebooted. HPE Aruba Networking 600R Series Remote Access Points |... -
Page 17: Kensington Lock Slot
The access point is equipped with a Kensington lock slot for additional physical security. DC Power Port The DC power port is designed for use with the HPE Aruba Networking AP-AC2-48C power adapter (included in the package). After inserting the L-shape DC connector into the DC power port, users can rotate the DC connector by 90 degrees and route the power cord to the left of the DC power port. - Page 18 Figure 22 Routing Power Cord HPE Aruba Networking 600R Series Remote Access Points |...
-
Page 19: Access Point Installation
Access Point Installation Access Point Installation All HPE Aruba Networking access points should be professionally installed by a professional installer. The installer is responsible for meeting applicable national and electrical codes. Failure to properly install this product may result in physical injury and/or damage to property. - Page 20 Figure 23 Removing Cellular Module from the Access Point Captive screws Mounting tab 2. Find the SIM ejector needle at the bottom of the cellular module. See HPE Aruba Networking 600R Series Remote Access Points |...
- Page 21 Figure 25 Opening the SIM Card Tray 4. Pull out the SIM card tray and insert a SIM card into the SIM tray. 5. Push the SIM card tray back into the slot. See Figure HPE Aruba Networking 600R Series Remote Access Points...
- Page 22 7. Insert the AP-605CM12 cellular module into the access point and tighten the two M3 captive screws using a Phillips screwdriver. See Figure Figure 27 Installing Cellular Module onto Access Point HPE Aruba Networking 600R Series Remote Access Points |...
-
Page 23: Software
Software Quick Start Guide. HPE Aruba Networking access points are classified as radio transmission devices, and are subject to government regulations of the host country. The network administrator(s) is/are responsible for ensuring that configuration and operation of this equipment is in compliance with their country’s regulations. For a complete list of approved channels in your country, refer to the HPE Aruba Networking Downloadable Regulatory Table at https://www.arubanetworks.com/techdocs/DRT/content/home.htm. -
Page 24: Specifications, Safety, And Compliance
Chapter 4 Specifications, Safety, and Compliance Specifications, Safety, and Compliance This chapter provides an overview of the HPE Aruba Networking 600R Series Remote Access Points specifications, safety, and compliance information. Electrical Ethernet: E0 port: 100/1000Base-T auto-sensing MDI/MDX wired RJ45 network connectivity port E1 port: 100/1000/2500Base-T auto-sensing MDI/MDX wired RJ45 network connectivity port... -
Page 25: Safety And Regulatory Compliance
Operation shall be limited to indoor use only; (b). Operation on oil platforms, cars, trains, boats and aircraft shall be prohibited except for on large aircraft flying above 10,000 ft. HPE Aruba Networking 600R Series Remote Access Points |... -
Page 26: Eu And Uk Regulatory Conformity
Kingdom's Radio Equipment Regulations 2017/UK is available for viewing below. Select the document that corresponds to your device’s model number as it is indicated on the product label. EU & UK Declaration of Conformity Compliance is only assured if the HPE Aruba Networking approved accessories as listed in the ordering guide are used. https://www.arubanetworks.com. -
Page 27: European Union And United Kingdom
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debeaceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada. HPE Aruba Networking 600R Series Remote Access Points |... -
Page 28: Нормативные Требования Евhразийского Экономического Союза
HPE Russia: ООО "Хьюлетт Паккард Энтерпрайз" Российская Федерация, 125171, г. Москва, Ленинградское шоссе, 16А, стр.3, Телефон: +7 499 403 4248 Факс: +7 499 403 4677 'HPE Kazakhstan': TOO «Хьюлетт-Паккард (К)», Республика Казахстан, 050040, г. Алматы, Бостандыкский район, проспект Аль-Фараби, 77/7, Телефон/факс: + 7 727 355 35 50 Kazakhstan ЖШС... -
Page 29: Ukca
2. Connect to only IEC 60950-1 or IEC 60601-1 certified products and power sources. The end user is responsible for the resulting medical system complies with the requirements of IEC 60601-1. 3. Wipe with a dry cloth, no additional maintenance required. HPE Aruba Networking 600R Series Remote Access Points |... - Page 30 4. No serviceable parts, the unit must be sent back to the manufacturer for repair. 5. No modifications are allowed without HPE Aruba Networking approval. HPE Aruba Networking 600R Series Remote Access Points...
Need help?
Do you have a question about the Aruba Networking 600R Series and is the answer not in the manual?
Questions and answers