Page 2
Hewlett Packard Enterprise Company. To obtain such source code, please check if the code is available in the HPE Software Center at https://myenterpriselicense.hpe.com/cwp-ui/software but, if not, send a written request for specific software version and product for which you want the open source code.
About This Guide About This Guide This document describes the hardware features of the HPE Aruba Networking 650 Series Campus Access Points. It provides a detailed overview of the physical and performance characteristics of each access point model and explains how to install the access point.
Hardware Overview Hardware Overview HPE Aruba Networking 650 Series Campus Access Points are high-performance, multi-radio wireless devices that can be deployed in either controller-based or controllerless network environments. These access points support the 802.11ax standard in the 2.4 GHz, 5 GHz, and 6 GHz bands with a 4x4 MIMO tri-radio Wi-Fi 6E platform.
Page 6
External Antenna Connector B0 (6GHz) External Antenna Connector B1 (6GHz) External Antenna Connector B2 (6GHz) External Antenna Connector B3 (6GHz) System LED Radio LED (2.4GHz) Radio LED (5GHz) Radio LED (6GHz) HPE Aruba Networking 650 Series Campus Access Points |...
MHz) for Standard Power operations (in conjunction with an Automated Frequency Coordination [AFC] system). Side A View Figure 3 AP-655 Access Point Side A View Callout Component USB Host Port HPE Aruba Networking 650 Series Campus Access Points | Installation Guide...
Figure 5 AP-655 Access Point Side B View Callout Component E0 Ethernet Port E1 Ethernet Port Figure 6 AP-654 Access Point Side B View Callout Component E0 Ethernet Port E1 Ethernet Port HPE Aruba Networking 650 Series Campus Access Points |...
Bluetooth Low Energy and IEEE 802.15.4 Radio 650 Series access points are equipped with an integrated BLE 5.0 and IEEE 802.15.4 (Zigbee) radio that provide the following capabilities: HPE Aruba Networking 650 Series Campus Access Points | Installation Guide...
The reset button located on the bottom of the device can be used to reset the access point to factory default settings or turn off/on the LED display. Use one of the following methods to reset the access point to factory default settings: To reset during normal operation: HPE Aruba Networking 650 Series Campus Access Points |...
The USB host interface state is updated to match what is configured in the management platform after the AP has established a connection and synchronized with the management platform. This state is maintained if the AP is power-cycled or rebooted. HPE Aruba Networking 650 Series Campus Access Points | Installation Guide...
Identifying Specific Installation Locations Use the access point placement map generated by HPE Aruba Networking 650 Series RF Plan software application to determine the proper installation location(s). Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference.
à la terre et que le circuit de mise à la terre est conforme aux codes électriques nationaux en vigueur. Le fait de ne pas installer correctement ce produit peut entraîner des blessures corporelles et / ou des dommages matériels. HPE Aruba Networking 650 Series Campus Access Points |...
The network administrator(s) is/are responsible for ensuring that configuration and operation of this equipment is in compliance with their country’s regulations. For a complete list of approved channels in your country, refer to the HPE Aruba Networking Downloadable Regulatory Table at https://www.arubanetworks.com/techdocs/DRT/Default.htm.
The regulatory model number RMN is not the marketing name or model number of the product. The following regulatory model numbers apply to the 650 Series: AP-654 RMN: APIN0654 AP-655 RMN: APIN0655 HPE Aruba Networking 650 Series Campus Access Points | Installation Guide...
HPE Aruba Networks provides a multi-language document that contains country-specific restrictions and additional safety and regulatory information for all HPE Aruba access points. This document can be viewed or downloaded at www.arubanetworks.com. Regulatory consideration for AP-654: AP-654 will be offered in countries where there is an existing or clear and defined path to allow operation of 6GHz radios with external connectorized antennas, either as a Low Power Indoor (LPI) or Standard Power (SPI) product.
Page 19
Antenne Gagner (2.4/5/6GHz) Impédance AP-ANT-311 3.0/6.0/6.0 50ohm AP-ANT-312 3.3/3.3/4.1 50ohm AP-ANT-313 3.0/6.0/6.0 50ohm AP-ANT-340 4.0/5.0/5.0 50ohm AP-ANT-345 4.5/5.5/5.5 50ohm AP-ANT-348 7.0/7.0/7.0 50ohm European Union and United Kingdom HPE Aruba Networking 650 Series Campus Access Points | Installation Guide...
Page 20
EU & UK Declaration of Conformity Compliance is only assured if the HPE Aruba Networking approved accessories as listed in the ordering guide are used. This device is limited for indoor use. Use in trains with metal-coated windows (or similar structures made of materials with comparable attenuation characteristic) and aircraft is permitted.
Operation in the 5.9725-7.125 GHz band is prohibited for control of or communication with unnamed aircraft systems. Proper Disposal of HPE Aruba Networking Equipment HPE Aruba Networking equipment complies with countries' national laws for proper disposal and electronic waste management. Waste of Electrical and Electronic Equipment...
Page 23
HPE Aruba Networking, a Hewlett Packard Enterprise company products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed- out wheelie bin).
Page 24
China RoHS HPE Aruba Networking 650 Series Campus Access Points |...
Page 25
Taiwan RoHS Turkey RoHS material content declaration Türkiye Cumhuriyeti: AEEE Yönetmeliğine Uygundur HPE Aruba Networking 650 Series Campus Access Points | Installation Guide...