Subscribe to Our Youtube Channel
Related Manuals for Ecler WPTI1CG2
Summary of Contents for Ecler WPTI1CG2
- Page 1 WPTI1CG2 VIDEO DISTRIBUTION OVER IP H.265 Full HD over IP Video Extenders USER MANUAL 50-0478-0100 WPTI1G2...
-
Page 2: Table Of Contents
6.1.5 Update ............................. 14 6.1.6 Log Out ............................15 6.2 Remote Controlling ........................15 6.2.1 Advanced Network Management ................... 15 6.3 Ecler VEO1CG2 Discovery App ....................16 7. PANEL FUNCTIONS ........................18 7.1 Front Panel ............................ 18 7.2 Rear Panel ............................. 19 8. -
Page 3: Precautions
WARNING: Ecler products have a long lifetime of more than 10 years. This product must never be discarded as unsorted urban waste, but must be taken to the nearest electrical and electronic waste treatment centre. -
Page 4: Key Safety Directions
1.2 Key Safety Directions Read the following directions. 11. Only use attachments/accessories specified by the manufacturer. Keep the following directions. 12. Unplug the device during lightning Observe all warnings. storms or when unused for long periods. Follow all instructions. Refer all servicing to qualified personnel. Do not use this device in proximity to Servicing is required when the device water. -
Page 5: Warranty & Environment
Recycling materials and using non-contaminant components are also top priorities in our green crusade. Ecler has deeply evaluated and analyzed the environmental impacts of all the processes involved in the production of this product, including packaging, and has alleviated, reduced and/or compensated for them. -
Page 6: Description & Features
4. DESCRIPTION & FEATURES WPTI1CG2 transmitter is a professional H.265 / H.264 device designed for HDMI® distribution over 1Gb Ethernet networks, supporting resolutions up to WUXGA and 1080p. It delivers high- quality video compression over distances of up to 100 meters using a single Cat 5e or higher cable. -
Page 7: Install & Connect
5. INSTALL & CONNECT 5.1 Wall Mounting This product can be mounted on a wall. The mounting steps are as follows: 1. Detach the white metal cover from the grey magnetic base. These parts are held together magnetically. 2. Secure the grey base to the wall-mounted junction box by inserting screws through the available holes. -
Page 8: Network Requirements And Configuration
5.2 Network Requirements and Configuration WPTI1CG2 is not limited to certain brands of network hardware, but the network must support the following network features: Layer 3 managed network switch. • IGMP snooping support. • To prevent malfunctioning, interference or drop in signal performance due to other network products bandwidth requirements or network design. -
Page 9: Video Distribution Quick Start
To begin a video transmission, a matching between a transmitter and a receiver is required. Each WPTI1CG2 or VEO-XTI1CG2 transmitter can stream a video signal over the network using an ID channel number that must be unique in the same network. Each ID channel from 0 to 762 identifies a IP address and every VEO-XRI1CG2 receiver can select one of these channels in order to receive an AV stream. -
Page 10: Multicast Mode
5.2.3 Multicast Mode When WPTI1CG2 and VEO-XRI1CG2 devices are connected in a point to multipoint or multipoint to multipoint topology, every transmitter and receiver should have a unique IP address. When possible, it is recommended to create an independent IP video network using managed network switches. -
Page 11: Start-Up & Operation
IP address of the chosen device into a web browser. Refer to Setting the IP address section for further details on how to find the IP address of a WPTI1CG2 and VEO-XRI1CG2. The default credentials to log in are: •... -
Page 12: Video Settings
• Bitrate: the user can adjust the video quality choosing the maximum transmitted data for the sub stream. 3. EDID Setting This parameter selects the EDID setting for the WPTI1CG2 transmitter. EDID ID EDID Description Video: HDMI 1080p@60Hz / Audio: Stereo PCM ... -
Page 13: Led
OFF: The Power LED stays on without blinking. o ON 90s: The Power LED blinks for 90s and then stops. o ALWAYS OFF: The Power LED stays off permanently. 6.1.4 Settings This page allows the user to modify the network configuration of the WPTI1CG2. -
Page 14: Update
Security This parameter turns on or off HTTPS security protocol. Setting Local ID: this parameter sets the ID Channel for the WPTI1CG2 transmitter from the 1-762 available profiles. Username This parameter lets the user modify the username assigned to the device. -
Page 15: Log Out
6.2.1 Advanced Network Management For larger AV over IP multicast scenarios involving several WPTI1CG2, VEO-XTI1CG2 and VEO-XRI1CG2 devices, it is recommended to add a VEO-XCTRLG2 controller module in the system. This unit will allow the user to manage and operate all the... -
Page 16: Ecler Veo1Cg2 Discovery App
6.3 Ecler VEO1CG2 Discovery App Ecler VEO1CG2 Discovery App is a downloadable software tool available from the official Ecler website. It runs as a standalone executable and is used to automatically detect all VEO-1CG2 series devices connected to the same local network. - Page 17 Name: Custom device name, configured via the WebGUI (see previous chapter). MAC Address: Physical MAC address of the device. IP Address: Device IP address. Clicking the blue link opens the device's WebSettings page in the default browser. Netmask: Device subnet mask. Gateway: Device gateway address.
-
Page 18: Panel Functions
7. PANEL FUNCTIONS 7.1 Front Panel HDMI IN: HDMI input port. POWER LED: The LED flashes when the device is power supplied and RESET: System reset button. stays lid (RED) after the start up is Pressing and holding for 5 seconds complete. -
Page 19: Rear Panel
7.2 Rear Panel LAN (PoE) CONNECTOR: Connect DATA LED Indicator (Yellow): the 1Gb network port to an Ethernet o Flashing: Data transmission switch to begin data transmission. o Light OFF: Data When PoE on the Ethernet switch is transmission available, the device will not need to DC 5V: Connect this port to the be locally powered. -
Page 20: Technical Data
8. TECHNICAL DATA 8.1 Technical Specifications WPTI1CG2 Video performances Video Input Connectors 1 x HDMI Type A Female, 1.4, 10.2 Gbps ® Video Input Resolutions 480i, 480p, 720i, 720p, 1080i, 1080p, 1920 x 1200 up to 60Hz Video Output Resolutions... -
Page 21: Mechanical Diagram
Shipping dimensions (WxHxD) 120 x 210 x 80 mm / 4.72 x 8.27 x 3.15 in. Shipping weight 0.29 Kg / 0.64 lb Chassis material Metal Finished colour White (RAL 9003) 8.2 Mechanical Diagram All measurements are in mm. - Page 22 NEEC AUDIO BARCELONA S.L. reserves the right to make changes or improvements in the design or manufacturing that may affect these product specifications. For technical queries contact your supplier, distributor or complete the contact form on our website, Support / Technical requests. Motors, 166‐168 08038 Barcelona, Spain Tel. (+34) 932238403 information@ecler.com www.ecler.com...
Need help?
Do you have a question about the WPTI1CG2 and is the answer not in the manual?
Questions and answers