Ecler VEO-XTI2L Tcp/Ip Control Manual
Low latency 4k over ip video extenders with kvm and videowall
Hide thumbs
Also See for VEO-XTI2L:
- User manual (57 pages) ,
- Quick start manual (12 pages) ,
- User manual (43 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Ecler VEO-XTI2L
Summary of Contents for Ecler VEO-XTI2L
- Page 1 VEO-XTI2L / VEO-XRI2L VIDEO DISTRIBUTION OVER IP Low latency 4K over IP Video Extenders with KVM and Videowall TCP/IP CONTROL MANUAL v.20190515...
-
Page 2: Table Of Contents
6.11. Reboot command ........................9 VIDEO WALL COMMANDS ....................10 HOW TO USE VEO-XTI2L and VEO-XRI2L as a TCP/RS232 converter ....13 HOW TO SEND CONTROL COMMANDS USING ECLERNET MANAGER ....14 9.1 Ecler Net Manager Net String Syntax ................. 14... -
Page 3: Important Remark
1. IMPORTANT REMARK The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. - Page 4 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.
-
Page 5: Important Note
3. IMPORTANT NOTE Thank you for choosing our VEO-XTI2L / VEO-XRI2L low latency 4K over IP video extenders. Please read the User Manual before making any connection in order to maximize your use and get the best performance from this equipment. -
Page 6: Control Commands
After “welcome message” is sent, you can login using root as username (no password needed). Once the “/ #” command prompt is shown, the device is ready to receive control commands. After each command, a carriage return CR char is required (0x0D in hex). 6. -
Page 7: Set Channel For A Specific Service
6.2. SET Channel for a specific service: Using the following commands it is possible to create independent routing of different services. For example, a receiver can receive a video stream from the transmitter set on channel 01 and a audio stream from the transmitter set as channel 02. ... -
Page 8: Set Stop_Link Command
6.4. SET Stop_link command: e e_stop_link This command allows to stop all the services on a receiver. It is possible to stop a specific service by choosing between the following: a: audio over IP v: video over IP ... -
Page 9: Set Hdmi Output Off Command
6.7. SET HDMI Output OFF command echo 1 > /sys/devices/platform/display/screen_off It switches HDMI out OFF. 6.8. SET Video stream Pause ON echo 1 > /sys/devices/platform/videoip/pause It allows freezing the video stream to the last frame shown before sending the command. 6.9. -
Page 10: Video Wall Commands
VEO-XRI2L. Each receiver must be set as “multicast” mode before sending the following commands (please check VEO-XTI2L VEO-XRI2L user manual on page 19). Screens are numbered as row_column from 0 to N-1, where N is the total number of screens per row and per column (max 8x8). - Page 11 It is also possible to manage each screen individually, in order to create custom compositions. The following example shows how to obtain a Picture in Picture using the top right screen. In this case this monitor is no longer a part of the video wall and operates as an independent screen receiving another channel (0002).
- Page 12 e e_vw_rotate_5 This command allows to rotate the image by 90 degrees clockwise. The image will be automatically scaled to the new resolution (portrait mode). e e_vw_rotate_6 This command allows to rotate the image by 90 degrees counterclockwise. The image will be automatically scaled to the new resolution (portrait mode).
-
Page 13: How To Use Veo-Xti2L And Veo-Xri2L As A Tcp/Rs232 Converter
RS-232 extension between transmitters and receivers. It is however possible to use the RS-232 port of VEO-XTI2L and VEOXRI2L extenders as a control port for third-party devices, just sending the desired command via TCP / IP and using the VEO devices as protocol translators. -
Page 14: How To Send Control Commands Using Eclernet Manager
Here below some examples about how to send control commands to VEO-XRI2L receiver devices using Net Strings Buttons on Ecler Net Manager. 9.1 Ecler Net Manager Net String Syntax When a Net String Button is used in ENM, the typical TCP command is structured like follows: |tcp|192.168.1.19|24|\d1root\re e_reconnect::0002\r\d1|... -
Page 15: Ecler Net Manager Net String Examples
\ char. space STX Start of text char; \x02 in hex. 9.2 Ecler Net Manager Net String Examples Set receiving channel 03: Create a video wall 1x2 receiving source channel 03:... - Page 16 Restore one of the screen as independent screen receiving channel 03: Send a RS-232 “PoweON” command followed by CR and LF commands to a 3 party device through the receiver RS-232 port:...
- Page 17 NEEC AUDIO BARCELONA S.L. reserves the right to make changes or improvements in the design or manufacturing that may affect these product specifications. Motors, 166‐168 08038 Barcelona ‐ Spain ‐ (+34) 932238403 | information@ecler.com www.ecler.com...