Related Manuals for Ecler VEO-XTI1CG2
Summary of Contents for Ecler VEO-XTI1CG2
- Page 1 VEO-XTI1CG2 / VEO-XRI1CG2 VIDEO DISTRIBUTION OVER IP H.265 Full HD over IP Video Extenders USER MANUAL 50-0430-0101 VEO-XTI1CG2 - VEO-XRI1CG2...
-
Page 2: Table Of Contents
6.2 VEO-XRI1CG2 (RX, receiver) ..................... 26 6.2.1 Front Panel ..........................26 6.2.2 Rear Panel ..........................27 6.3 Additional Functionalities of CH Select ▲/▼ buttons for both: VEO-XTI1CG2 and VEO-XRI1CG2 ....................... 28 TECHNICAL DATA ......................31 7.1 Technical Specifications ...................... 31 7.2 Mechanical Diagram ......................33 7.2.1... -
Page 3: Precautions
1. PRECAUTIONS 1.1 IMPORTANT REMARK The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. -
Page 4: Important Safety Instructions
1.2 IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this device near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other device (including amplifiers) that produce heat. -
Page 5: Cleaning
CLEANING Clean the unit with a soft, dry clean cloth or slightly wet with water and neutral liquid soap only, then dry it with a clean cloth. Be careful that water never gets into the unit through any hole. Never use alcohol, benzine, solvents or abrasive substances to clean this unit. -
Page 6: Package Contents
To ensure optimal operation of this device, we strongly recommend that its maintenance be carried out by our authorised Technical Services. Ecler VEO-XTI1CG2 and VEO-XRI1CG2 come with a 5-year warranty. 2. PACKAGE CONTENTS 2.1 VEO-XTI1CG2 •... -
Page 7: Description And Features
3. DESCRIPTION and FEATURES VEO-XTI1CG2 transmitter and VEO-XRI1CG2 receiver are a H.265 / H.264 over IP set of extenders that allow for HDMI distribution over 1Gb Ethernet networks with up to 1080p@60Hz video support. These devices represent a professional high-quality compression and low bandwidth solution aimed for point-to-point, as well as multipoint- to-multipoint scenarios over a single 100m Cat5e/6/7 cable. -
Page 8: Install & Connect
4. INSTALL & CONNECT 4.1 RACK MOUNTING This product can be mounted in a standard rack: Stack two products on top of each other. Then use the included screws to fix two 1U mounting ears on the products. 2. Place four pairs of products together with each other using the provided screws. 3. -
Page 9: Network Requirements And Configuration
4.2 NETWORK REQUIREMENTS AND CONFIGURATION VEO-XTI1CG2 and VEO-XRI1CG2 are not limited to certain brands of network hardware, but the network must support the following network features: • Type of layer 3 managed network switch. • Support and enable IGMP snooping and the adequate multicast filtering. -
Page 10: Video Distribution Quick Start
To begin a video transmission, a matching between an encoder and a decoder is required. Each VEO-XTI1CG2 transmitter can stream a video signal over the network using an ID channel number that must be unique in the same network. Each ID channel from 0 to 762 identifies a multicast address and every VEO-XRI1CG2 receiver can select one of these channels in order to receive an AV stream. -
Page 11: Multicast Mode
4.2.4 MULTICAST MODE When VEO-XTI1CG2 and VEO-XRI1CG2 devices are connected in a point to multipoint or multipoint to multipoint topology, every transmitter and receiver should have a unique IP address. When possible, it is recommended to create an independent IP video network using managed network switches. -
Page 12: Start-Up And Operation
5. START-UP and OPERATION 5.1 CONFIGURATION USING WEB INTERFACE VEO-XTI1CG2 and VEO-XRI1CG2 devices can be configured through their own built-in web interface by simply typing the IP address of the chosen device into a web browser. The default credentials to log in are: •... -
Page 13: Video Settings
5.1.2 VIDEO SETTINGS 5.1.2.1 VEO-XTI1CG2 VIDEO SETTINGS The video settings page will enable the user to configure the following parameters for VEO-XTI1CG2. Main Stream • Video Encoding Format: the user can select H.265 and H.264 video codec for the mainstream. - Page 14 ID Setting This parameter selects the local ID for the VEO-XTI1CG2 transmitter from the available 1-762 channels. Audio Selection This parameter lets the user choose the Audio mode (ANALOGUE / HDMI) for the VEO-XTI1CG2 transmitter’s AUDIO IN. EDID Setting This parameter selects the EDID setting for the VEO-XTI1CG2 transmitter. For further details, refer to Additional functionalities of CH select ▲/▼...
- Page 15 5.1.2.2 VEO-XRI1CG2: VIDEO SETTINGS The video settings page will enable the user to configure the following parameters for VEO-XRI1CG2. Transmission This parameter selects UNICAST or MULTICAST as the chosen network transmission protocol. Scaler Setting This parameter sets the output resolution scaling up on the HDMI OUT of the VEO- XRI1CG2 receiver.
- Page 16 This parameter enables the user to download the EDID binary file of the endpoint device connected to the VEO-XRI1CG2 receiver. The EDID file can be used as the User EDID file to be uploaded to the VEO-XTI1CG2. Video Timeout Setting This parameter sets the timeout time to turn off the HDMI OUT output when no video signal is detected.
-
Page 17: Led
5.1.3 This page allows the user to select the led status for both, VEO-XTI1CG2 and VEO- XRI1CG2. Front Panel Power LED Flash: This parameter selects the status of the Front Panel LED as follows: • ON: The LED remains permanently lighted. -
Page 18: Settings
5.1.4 SETTINGS This page allows the user to modify the network configuration of the VEO-XTI1CG2 and VEO-XRI1CG2 devices. Network • IP address Subnet Mask • • Gateway • HTTP Web Port • The Network Settings can be set only when the MODE button is set to Static. -
Page 19: Update
5.1.5 UPDATE 5.1.5.1 VEO-XTI1CG2 UPDATE Firmware Update: • Browse: This will import the upgrade file. • Update: This will start the upgrade process. When the progress bar reaches 100%, the upgrade is successful, and the device will restart. Factory Reset: This will reset the device to the factory default settings. -
Page 20: Log Out
5.1.6 LOG OUT Selecting Log Out will exit the Web GUI and skip to the login interface automatically. 5.2 REMOTE CONTROLLING 5.2.1 RS-232 To match the ID from a transmitter to a receiver, connect the RS-232 port of VEO- XTI1CG2 and VEO-XRI1CG2 to a PC serial interface or a RS-232 control system. 5.2.1.1 RS-232 COMMUNICATION PROTOCOL The serial parameters for a correct transmission are: Baud rate 115200... - Page 21 RESPONSE Set RX ID xxx to SCALE yyy PARAMETERS DESCRIPTION • xxx: RX ID number to be set, ranging from 1 to 762 • yyy: SCALE mode number, range • 0~19,0:Pass Through (default); 1: HDMI 1080p@60Hz; 2: HDMI 1080p@50Hz; 3: HDMI 1080p@30Hz; 4: HDMI 1080p@25Hz;...
- Page 22 RESPONSE Set TX ID xxx EDID to yyy PARAMETERS DESCRIPTION • xxx: TX ID number to be set, range 1~762 • yyy: EDID serial number, range 0~7, • 0: HDMI 1080p@60Hz , Audio 2CH PCM (default) ; Set INPUT xxx !IN xxx EDID yyy •...
-
Page 23: Advanced Network Management
TCP commands to remotely communicate with VEO-XTI1CG2 and VEO-XRI1CG2 units present in the network. For further details on how to set up an advanced networked installation control layout interface, please refer to VEO-... -
Page 24: Panel Functions
When clicking the “SHOW ME” option on the VEO-XCTRLG2, the status display will flash “SHO” for an easier location of the corresponding device. For further details, refer to Additional functionalities of CH select ▲/▼ buttons for both: VEO-XTI1CG2 & VEO-XRI1CG2 chapter. -
Page 25: Rear Panel
6.1.2 REAR PANEL RS-232: Serial port for remote control. Signal pass-through supported. AUDIO IN/OUT: o AUDIO IN: When this mode is selected, the audio port acts as an input (audio embedding to HDMI). o AUDIO OUT: When this mode is selected, the audio port acts as an output (audio extraction from HDMI). -
Page 26: Veo-Xri1Cg2 (Rx, Receiver)
When clicking the “SHOW ME” option on the XCTRLG2, the status display will flash “SHO” for an easier location of the corresponding device. For further details, refer to Additional functionalities of CH select ▲/▼ buttons for both: VEO-XTI1CG2 & VEO- XRI1CG2 chapter. -
Page 27: Rear Panel
6.2.2 REAR PANEL RS-232: Serial port for remote control. Signal pass-through supported. AUDIO OUT: The audio port acts as an audio de-embedder from HDMI. LAN (PoE) CONNECTOR: Connect the 1Gb network port to an Ethernet switch to begin data transmission. When PoE on the Ethernet switch is available, the device will not need to be locally powered. -
Page 28: Additional Functionalities Of Ch Select ▲/▼ Buttons For Both: Veo-Xti1Cg2 And Veo-Xri1Cg2
Status display. This message will appear following the sequence "xxx", After the system is powered on, the VEO-XTI1CG2 / VEO- XRI1G2 device Status display will show the ID Channel. When idle and Display configured as OFF, pressing ▲ or ▼ button will ▲... - Page 29 ▲ ▼ VEO-XTI1CG2) • AHE: HDMI embedded audio signal will be outputted through AUDIO OUT ports on VEO-XTI1CG2 and VEO- XRI1CG2 • AEI: External audio source signal coming in AUDIO IN on VEO-XTI1CG2 will be outputted through AUDIO OUT port on VEO-XRI1CG2.
- Page 30 Long pressing the ▲ or ▼ button until the Status display shows “S00” (in which “S” refers to Scaler and “00” to resolution ID). Then pressing and holding ▲ and ▼ buttons both together for 5 seconds, will enter the “Output Resolution Settings”...
-
Page 31: Technical Data
Not supported Video Composing Capabilities Videowall up to 9x9 Scaling Feature Supported HDMI Distance 15m with Ecler VEO Cables Audio Performances Audio Input Connectors Transmitter: 3-pin Euroblock (Stereo Unbalanced) Audio Output Connectors Receiver and Transmitter: 3-pin Euroblock (Stereo Unbalanced) Audio Formats LPCM 2.0CH... - Page 32 Physical Operating Temperature Min. -10°C - 14°F; Max. 45°C - 113°F Operating Humidity <90% HR Installation Options Desktop, 19" racks (1/2RU), VEO-RACK19 Included Accessories ▪ 2x 3pins Euroblock connector ▪ 4x M3 screws 4mm ▪ 2x Mounting Ears ▪ 1x 12V PSU Optional Accessories VEO-RACK19 Dimensions (WxHxD)
-
Page 33: Mechanical Diagram
7.2 MECHANICAL DIAGRAM 7.2.1 VEO-XTI1CG2 7.2.2 VEO-XRI1CG2... - Page 34 NEEC AUDIO BARCELONA S.L. reserves the right to make changes or improvements in the design or manufacturing that may affect these product specifications. For technical queries contact your supplier, distributor or complete the contact form on our website, Support / Technical requests. Motors, 166‐168 -08038 Barcelona ‐ Spain‐(+34) 932238403 information@ecler.com www.ecler.com...
Need help?
Do you have a question about the VEO-XTI1CG2 and is the answer not in the manual?
Questions and answers