Subscribe to Our Youtube Channel
Related Manuals for CORNING E62-X3
Summary of Contents for CORNING E62-X3
- Page 1 INSTALLATION MANUAL E62-X3 HIGH POWER 4T4R Digital Radio 280MHz IBW Outdoor Rated Confidential - Corning (L3)
-
Page 2: Revision History
E62-X3 4T4R Digital Radio Revision History Revision Number Revision Date Summary of Changes Author 1.0.0 May, 2023 New Format Gabriel Kollat Contact us today IM_CN_X3 v1.0.0 | 2 of 42... -
Page 3: Table Of Contents
E3 Rack Installation ..................................17 E3 Wall Installation ..................................21 E3 Wall Mounting Dimension Spacing ............................. 24 Installing the Mid Power Remote Unit (E62-X3) ............................25 Accessories List ....................................26 Wall Installation (Back on the Wall) ..............................27 Wall Installation (Side on the Wall) ..............................34 Pole Installation .................................... -
Page 4: General
The equipment has to operate within the following humidity level and temperature range: Humidity: 5-95% (Non-Condensing) Operating Temperature range (A3/E3): -10 to 45℃ Operating Temperature range (E62-X3): -40 to 55℃ Contact us today IM_CN_X3 v1.0.0 | 4 of 42... -
Page 5: Preparation
3. Ensure that all equipment and accessories have no damage. If there is any damage, contact your Corning service agent. Tools Electric drill, cross head screwdriver, side cutters, ladder, and other tools are needed for E62-X3 installation which is not offered from Corning for now. Customers to provide these tools themselves. -
Page 6: Optical Transceiver Module
E62-X3 4T4R Digital Radio Optical Transceiver Module Single Port Bidirectional SFP Transceiver The Figure below shows a pair of single port Bidirectional SFP transceivers. For devices optical connection, the transceivers of two sides must be paired - the wavelength of one side is 1270nm, and the wavelength of another side is 1330nm. Otherwise, it will fail the connection. -
Page 7: Installation Of The A3
E62-X3 4T4R Digital Radio Installation of the A3 A3 Accessories Screw M6*16 Screw M3*6 Suspension Loop-R(white Suspension Loop-L(white mark ’L‘) AC Power Lead mark ’R‘) CAT-5 Cable 1.5m CAT-5 Cable For Fan Ground Wire Figure 1. A3 Accessories Note: the ground wire of A3 is 12AWG and 2 meter in Accessories package. -
Page 8: A3 Rack Installation
E62-X3 4T4R Digital Radio A3 Rack Installation The Access Unit is a 19” 1U equipment shelf, which is 2U with Fan integrated. When installing the Access Unit in a rack, make sure the mechanical loading of the rack is even to avoid a hazardous condition. The rack should safely support the combined weight of all the equipment and be securely anchored. - Page 9 E62-X3 4T4R Digital Radio Figure 3. Connect Fan Cable Recommended attaching the sliding rails to rack. (Not included in delivery). Figure 4. Sliding Rails Place the A3 in the rack and secure the A3 using 4 screws M6×16 on both side and the Phillips screwdriver.
- Page 10 E62-X3 4T4R Digital Radio Figure 5. Place A3 in Rack Figure 6. Rack Installation Contact us today IM_CN_X3 v1.0.0 | 10 of 42...
- Page 11 E62-X3 4T4R Digital Radio Connect and lock the power cable at the A3 rear side. Connect and screw the ground wire at the A3 rear side. Figure 7. Connect Power and Ground Cables Figure 8. Installation Completed Contact us today...
-
Page 12: A3 Wall Installation
E62-X3 4T4R Digital Radio A3 Wall Installation To install the Access Unit on the wall: Rotate the handles 90°and attach them at the rear of the A3, using 8 screws M3×6 per bracket and the Phillips screwdriver. Observe the orientation of the brackets. - Page 13 E62-X3 4T4R Digital Radio Mark 4 x ∅6.8mm drilling holes sites for the hanger to be attached to the wall. Figure 10. Mark Drilling Hole Drill 4 holes at the marked sites using percussion drill and embed 4×∅10 plastic expansion pipes. Note: H=70mm.
- Page 14 E62-X3 4T4R Digital Radio Connect and lock the power cable at the A3 rear side Connect and screw the ground wire at the A3 rear side Figure 12. Connect Power and Ground Cables Figure 13. A3 Wall Mounting Completed Contact us today...
-
Page 15: A3 Wall Mounting Dimension Spacing
E62-X3 4T4R Digital Radio A3 Wall Mounting Dimension Spacing Figure 14. A3 Wall Mounting Dimension Spacing Contact us today IM_CN_X3 v1.0.0 | 15 of 42... -
Page 16: Installing The Expansion Unit (E3-O)
E62-X3 4T4R Digital Radio Installing the Expansion Unit (E3-O) E3-O Accessories List Screw M6*16 Screw M3*6 Suspension Loo AC Power Lead SFP28 modules Ground Wire Contact us today IM_CN_X3 v1.0.0 | 16 of 42... -
Page 17: E3 Rack Installation
E62-X3 4T4R Digital Radio E3 Rack Installation The Expansion Unit is a 19” 1U equipment shelf. When installing the Expansion Unit in a rack, make sure the mechanical loading of the rack is even to avoid a hazardous condition. The rack should safely support the combined weight of all the equipment and be securely anchored. - Page 18 E62-X3 4T4R Digital Radio Recommended attaching the sliding rails to rack. (Not included in delivery). Figure 16. E3 Sliding Rails Place the E3 in the rack and secure the E3 using 2 screws M6×16 on both side and the Phillips screwdriver.
- Page 19 E62-X3 4T4R Digital Radio Figure 18. E3 in Rack Reserve enough free space or Install the fan for cooling if multiple devices are installed in the same rack. It is necessary to allow at least 1 rack unit (44mm) of free space above and below the E3 for heat dissipation or with 1 unit fan installed in the middle.
- Page 20 E62-X3 4T4R Digital Radio Connect and lock the power cable at the E3 rear side. Connect and screw the ground wire at the E3 rear side. Figure 20. Connect Power and Ground Cables Figure 21. E3 Rack Mounting Completed Contact us today...
-
Page 21: E3 Wall Installation
E62-X3 4T4R Digital Radio E3 Wall Installation To install the Expansion Unit on the wall: Rotate the handles 90°and attach them at the rear of the E3, using 4 M3×6 screws per bracket and the Phillips screwdriver. Observe the orientation of the brackets. - Page 22 E62-X3 4T4R Digital Radio Mark 4 x ∅6.8mm drilling holes sites for the hanger to be attached to the wall Figure 23. Mark Drilling Holes Drill 4 holes at the marked sites using percussion drill and embed 4×∅10 plastic expansion pipes. Note: H=70mm.
- Page 23 E62-X3 4T4R Digital Radio Connect and lock the power cable at the A3 rear side Connect and screw the ground wire at the A3 rear side Figure 25. Connect Power and Ground Cables Figure 26. E3 Wall Mounting Completed Contact us today...
-
Page 24: E3 Wall Mounting Dimension Spacing
E62-X3 4T4R Digital Radio E3 Wall Mounting Dimension Spacing Figure 27. E3 Wall Mounting Dimension Spacing Contact us today IM_CN_X3 v1.0.0 | 24 of 42... -
Page 25: Installing The Mid Power Remote Unit (E62-X3)
E62-X3 4T4R Digital Radio Installing the Mid Power Remote Unit (E62-X3) Figure 28. E62-X3 Contact us today IM_CN_X3 v1.0.0 | 25 of 42... -
Page 26: Accessories List
E62-X3 4T4R Digital Radio Accessories List Contact us today IM_CN_X3 v1.0.0 | 26 of 42... -
Page 27: Wall Installation (Back On The Wall)
Attach and fasten the handle to the side of E62-X3 with screws M6×14 using T5 Wrench. Figure 29. Attach the handle to the E62-X3 Side Attach and fasten the Bracket I to the back of E62-X3 with screws M6×14 using T5 Wrench. Figure 30. Attach the Bracket I to E62-X3 Back Contact us today IM_CN_X3 v1.0.0 | 27 of 42... - Page 28 Figure 32. Mark the holes’ position for Bracket II Attach the dowels, expansion screws or the like and fasten the Bracket II to the wall. Tips: use Bracket II as a reference to control each devices’ separation distance before hanging and locking E62-X3 up. Contact us today...
- Page 29 E62-X3 4T4R Digital Radio Figure 33. Fasten the Bracket II to the wall Hang the E62-X3 on the mounting bracket II and fasten with nuts M10. Figure 34. Hang the E62-X3 on the Bracket II Contact us today IM_CN_X3 v1.0.0 | 29 of 42...
- Page 30 4T4R Digital Radio Fasten the Bracket I and II with screws M6×14. Figure 35. Fasten the Bracket I and II Connect and lock the power cable at the E62-X3 rear side Figure 36. Connect the Power Cable of E62-X3 Contact us today...
- Page 31 E62-X3 4T4R Digital Radio Connect and screw the ground cable at the E62-X3’s left side Figure 37. Connect the Grouding Cable of E62-X3 Contact us today IM_CN_X3 v1.0.0 | 31 of 42...
- Page 32 E62-X3 4T4R Digital Radio 10. Open the box on the right of E62-X3 and connect SFP module. Figure 38. Open the Box and connect the SFP Contact us today IM_CN_X3 v1.0.0 | 32 of 42...
- Page 33 E62-X3 4T4R Digital Radio Contact us today IM_CN_X3 v1.0.0 | 33 of 42...
-
Page 34: Wall Installation (Side On The Wall)
Attach and fasten the handle to the side of E62-X3 with screws M6×14 using T5 Wrench. Figure 40. Attach the handle to the E62-X3 Side Attach and fasten the Bracket I to the left side of E62-X3 with screws M6×14 using T5 Wrench. Figure 41. Attach the Bracket I to E62-X3 Side Contact us today IM_CN_X3 v1.0.0 | 34 of 42... - Page 35 Figure 43. Drill the holes for Bracket II Attach the dowels, expansion screws or the like and fasten the Bracket II to the wall. Tips: use Bracket II as a reference to control each devices’ separation distance before hanging and locking E62-X3 up. Contact us today...
- Page 36 E62-X3 4T4R Digital Radio Figure 44. Fasten the Bracket II to the wall Hang the E62-X3 on the mounting bracket II and fasten with nuts M10. Figure 45. Hang the E62-X3 on the Bracket II Contact us today IM_CN_X3 v1.0.0 | 36 of 42...
- Page 37 Fasten the Bracket I and II with screws M6×14. Figure 46. Fasten the Bracket I and II Connect and lock the power cable at the E62-X3 rear side Figure 47. Connect the Power Cable of E62-X3 Connect and screw the ground cable at the E62-X3’s left side.
- Page 38 E62-X3 4T4R Digital Radio Figure 48. Connect the Grouding Cable of E62-X3 10. Open the box on the right of E62-X3 and connect SFP module. Contact us today IM_CN_X3 v1.0.0 | 38 of 42...
- Page 39 E62-X3 4T4R Digital Radio Figure 49. Open the Box and connect the SFP 11. E62-X3 Intalled Side on the Wall. Figure 50. E62-X3 Intalled Side on the Wall Contact us today IM_CN_X3 v1.0.0 | 39 of 42...
-
Page 40: Pole Installation
Install the handle and Bracket I to the back of E62-X3. Install the bracket II and Bracket III to the pole. Hang the E62-X3 on the mounting bracket and fasten with nuts M10. Connect the ground cable and power cable. -
Page 41: E62-X3 Mounting Dimension Spacing
E62-X3 4T4R Digital Radio E62-X3 Mounting Dimension Spacing Contact us today IM_CN_X3 v1.0.0 | 41 of 42... -
Page 42: This Device Must Accept Any Interference Received, Including Interference That May Cause Undesired Operation
RF exposure in a workplace or similar environment can be provided through specific training as part of a RF safety program. Figure 52. E62-X3 Wall Mounting Dimension Spacing Contact us today IM_CN_X3 v1.0.0 | 42 of 42...
Need help?
Do you have a question about the E62-X3 and is the answer not in the manual?
Questions and answers