Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Staubli MC4-Evo 1
Summary of Contents for Staubli MC4-Evo 1
- Page 1 Connector MC4-Evo 1 Assembly instructions MA718...
-
Page 2: Safety Instructions
ONLY approved PV cables shall be assembled to the connector. Safe assembly and mounting Live parts can remain energized after isolation or dis- connection. • ONLY Install the product when the PV module is de-energized. 2 Assembly instructions | Connector MC4-Evo 1... - Page 3 NEVER mate contaminated connectors. • Use of tool is required to open locking-type connector. • Do NOT modify or repair Mount connectors only once. • component Do NOT modify connectors after assembly. • Replace defective connectors. Assembly instructions | Connector MC4-Evo 1 3...
-
Page 4: Notes On Installation
• Do not allow that the connector is at the lowest point of cabling where water can collect. NOTE Refer to cable manufacturers specification for mini- mum radius. 4 Assembly instructions | Connector MC4-Evo 1... - Page 5 • Installation in areas that restrict the air flow (e.g. in large bundles, in split looms or other housings) is not permitted. • Direct burial of the connector is not permitted. Assembly instructions | Connector MC4-Evo 1 5...
-
Page 6: Product Overview
The components must not be exposed to moisture due to direct rainfall, condensation or similar. • Do not allow components to come into contact with acids, alkalis, gases, acetone or other chemically aggressive substances. 6 Assembly instructions | Connector MC4-Evo 1... - Page 7 PV-MS-MC4-Evo 1 – – MC4-Evo 1 Test plug PV-PST-EVO 1 – – Cable cutter PV-WZ-KS – MA705 3.3 Optional accessories Product Type Assembly instructions Socket sealing cap PV-BVK4 MA258 Plug sealing cap PV-SVK4 Assembly instructions | Connector MC4-Evo 1 7...
-
Page 8: Cable Preparation
• In case that other diameters than those mentioned in above table are used, contact Stäubli. 4.1 MC4-Evo 1 product configuration under TÜV Rheinland certification Cables connected to the connectors shall be suitable for use in photovoltaic systems and shall comply with the requirements of IEC 62930. -
Page 9: Assembly Check
6. Assembly check • Insert the crimped contact into the insulator until it clicks into place. Pull gently on the cable to verify that the contact is correctly engaged Assembly instructions | Connector MC4-Evo 1 9... - Page 10 The contact is correctly installed if the groove on the test plug is still visible. • Tighten cap nut using open-end spanner set MC4-Evo 1 until the cap nut is bottomed out. NOTE • 0 mm For assembly of components an ambient temperature between -10 °C and 45 °C with a...
-
Page 11: Technical Data
Transportation/storage relative humidity < 70 % RH Design Locking system Locking type Type of termination Crimping Contact system MULTILAM Material Contact material copper (tin plated) Insulation material Certifications TÜV-Rheinland certified according to IEC 62852:2014+A1:2020 TÜV Rheinland certificate Nr. R 50661885 Assembly instructions | Connector MC4-Evo 1 11... - Page 12 Stäubli Electrical Connectors AG Stockbrunnenrain 8 4123 Allschwil/Switzerland Tel. +41 61 306 55 55 +41 61 306 55 56 E-Mail ec.ch@staubli.com www.staubli.com/electrical www.staubli.com © by Stäubli Electrical Connectors AG, Switzerland MA718 – 05.2025, Index a Marketing Communications – Subject to alterations...
Need help?
Do you have a question about the MC4-Evo 1 and is the answer not in the manual?
Questions and answers