1. Manuals
  2. Brands
  3. Cedar Summit Manuals
  4. Play Sets & Playground Equipment
  5. GEORGIAN MANOR
  6. Installation and operating instructions manual

Cedar Summit GEORGIAN MANOR Installation And Operating Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
G E O R G I A N M A N O R - P 2 8 0 0 6 8
INSTALLATION AND OPERATING INSTRUCTIONS
5' 10" (1.78 m)
PLAY STRUCTURE SET-UP WITH
USER ZONE DIMENSIONS:
5'10" x 4'6" (1.78m x 1.37m)
6 - 10 Hrs
Two person
assembly
Rev 08/30/2013
9400068
WARNING
and give them to any future owner of this play system. Manufacturer contact information provided below.
CAPACITY - 5 Users Maximum, Ages 2 to 10.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares or parks.
Cedar Summit
c/o ©Solowave Design LP
Mount Forest, ON Canada
N0G 2L0
www . c edarsummitplay . c om
support@cedarsummitplay . c om
Customer Service
1-877-817-5682 (toll free)
1-519-323-2258
To reduce the risk of serious injury or death, you must read and
follow these instructions. Keep and refer to these instructions often

Table of Contents

Warnings and Safe Play Instructions . . . . . . . . . . .pg . 2
Instructions for Proper Maintenance . . . . . . . . . . .pg . 2
Keys to Assembly Success . . . . . . . . . . . . . . . . . . . . .pg . 3
About Our Wood - Limited Warranty . . . . . . . . . . .pg . 4
Keys to Quick Assembly . . . . . . . . . . . . . . . . . . . . . . .pg . 5
Part ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .pg . 6
Step-By-Step Instructions . . . . . . . . . . . . . . . . . . . . pg . 17
Installation of Playhouse Plaque . . . . . . . . . .Final Step

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GEORGIAN MANOR and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Cedar Summit GEORGIAN MANOR

Summary of Contents for Cedar Summit GEORGIAN MANOR

  • Page 1: Table Of Contents

    Two person assembly Table of Contents Cedar Summit c/o ©Solowave Design LP Warnings and Safe Play Instructions . . . . . . . . . . .pg . 2 Mount Forest, ON Canada Instructions for Proper Maintenance .

  • Page 2: Warnings And Safe Play Instructions

    Instructions for Proper Maintenance Your Cedar Summit Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Playhouse, it is important that you, the owner, properly maintain it.

  • Page 3: Keys To Assembly Success

    Keys to Assembly Success Tools Required • #1, #2 & Phillips • Open End Wrench • Safety Glasses • Tape Measure or Robertson Bits (7/16”) • Adult Helpers • Carpenters Level or Screwdriver • Adjustable Wrench • Carpenters Square • Ratchet with extension •...

  • Page 4: About Our Wood - Limited Warranty

    About Our Wood Cedar Summit Premium Play Systems uses 100% FSC wood. Although we take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible to weathering which can change the appearance of your set.

  • Page 5: Keys To Quick Assembly

    Your Key To Quick Assembly SORTING WOOD PARTS INTO EACH ASSEMBL Y STEP WILL SAVE TIME! Step Step Step SAVE TIME - TIP #1: Open box with wood parts and look for the Key Number stamped on the end of the wood part (see chart below). Sort each wood part into the different assembly steps.

  • Page 6: Part Id

    Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) 2pc. - 184 - 10 x 25.4 x 413.8 - Window Trim FSC - 48033636 (3/8 x 1 x 16‐5/16") 48041136 2pc. - 136 - 15.9 x 76.2 x 533.7 - Cafe Side FSC - (5/8 x 3 x 21") 48041036 1pc.
  • Page 7 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) 1pc. - 172 - 15.9 x 82.6 x 755.6 - Gable Block Short FSC - 48037936 (5/8 x 3‐1/4 x 29‐3/4") 1pc. - 064 - 15.9 x 82.6 x 1214.4 - Counter Back FSC - 48036236 (5/8 x 3‐1/4 x 47‐13/16") 2pc.
  • Page 8 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) 2pc. - 023 - 23.8 x 82.6 x 406.4 - Bench Base Cafe (Green) FSC - 48041701 (15/16 x 3‐1/4 x 16") 48034801 2pc. - 024 - 23.8 x 82.6 x 798.5 - Bench Top Cafe (Green) FSC - (15/16 x 3‐1/4 x 31‐7/16") 1pc.
  • Page 9 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) 1pc. - 182 - 36.5 x 63.5 x 206.5 - Window Arch Asy (Green) FSC - 478041601 (1‐7/16 x 2‐1/2 x 8‐1/8") 478039301 2pc. - 031 - 28.6 x 190 x 419.1 - Shutter Asy (Green) FSC - (1‐1/8 x 7‐1/2 x 16‐1/2") 478032636 1pc.
  • Page 10 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) 1pc. - 051 - 27.8 x 708.8 x 760.6 - Dormer Roof Panel Left FSC - 478040936 (1‐1/8 x 27‐7/8 x 29‐15/16") 1pc. - 052 - 27.8 x 708.8 x 760.6 - Dormer Roof Panel Right 478040836 (1‐1/8 x 27‐7/8 x 29‐15/16") 1pc.- 191 -...
  • Page 11 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) 478040636 1pc. - 081 - 27.8 x 1016 x 1073.2 - Shutter Wall Panel FSC - (1‐1/8 x 40 x 42‐1/4") 478040736 1pc. - 092 - 27.8 x 1016 x 1214.4 - Back Wall Panel FSC - (1‐1/8 x 40 x 47‐13/16") support@cedarsummitplay.com...
  • Page 12 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) 1pc. - 043 - 33.7 x 920.5 x 1270 - Back Roof Panel FSC - 478040136 (1‐5/16 x 36‐1/4 x 50") 1pc. - 042 - 33.7 x 926.9 x 1270 - Front Roof Panel FSC - 478040236 (1‐5/16 x 36‐1/2 x 50") support@cedarsummitplay.com...
  • Page 13 Hardware Identification (Actual Size) Hex Bolt 1/4 x 1-1/2" 2pc. H1 - - (53705212) 8pc. TN1 - 1/4" T - Nut (54505200) Hex Bolt 1/4 x 2" 6pc. H2 - - (53705220) 6pc. FW1 - 1/4" Flat Washer - (51105200) #8 x 2-1/2"...
  • Page 14 Part Identification (Reduced Part Size) 1x - Georgian Manor Brkt Set (Green) (3201568) 2x - Flower Box (Green) 10x - Corner Bracket (9320401) (9201570) 1x - Shutter Pivot w. hardware (4Pk) (3320790) 2x - U-Bracket (9201570) www.cedarsummitplay.com Solowave Design LP...
  • Page 15 support@cedarsummitplay.com...
  • Page 16 support@cedarsummitplay.com...
  • Page 17 Step 1: Inventory Parts - Read This Before Starting Assembly STOP STOP STOP STOP This is the time for you to inventory all your hardware, wood and accessories, referencing the parts identification sheets. This will assist you with your assembly. •...

  • Page 18: Step 2: Bench Assembly

    Step 2: Bench Assembly Part 1 A: Flush to the top of 1 (022) Bench Leg Cafe place 1 (021) Bench End Support Cafe, angled corners facing down and centred on the legs. Attach with 2 (S2) #8 x 1-1/2” Wood Screws and 1 (H2) 1/4 x 2” Hex Bolt (with lock washer, flat washer and t-nut).
  • Page 19 Step 2: Bench Assembly Part 2 D: Place 2 (024) Bench Top Cafes on both Bench Leg Assemblies so the ends on each side hang over by 1”. Outside edges of each (024) Bench Top Cafe to be flush to outside edge of each (021) Bench End Support Cafe. Attach each (024) Bench Top Cafe to each (021) Bench End Support Cafe with 4 (S15) #8 x 1-3/4”...

  • Page 20: Step 3: Shutter Assembly

    Step 3: Shutter Assembly A: Place 1 Door Handle on each (031) Shutter Assembly centred over 1 panel as shown in fig. 3.1. Attach with 2 (S13) #6 x 5/8” Pan Screws per handle. B: On the opposite side as the Door Handles attach 2 Shutter Pivots to each (031) Shutter Assembly using provided hardware, as shown in fig.

  • Page 21: Step 4: Roof Assembly

    Step 4: Roof Assembly Part 1 A: Attach 1 (041) Roof Side to another flush at the peak using 2 (S3) #8 x 2-1/2” Wood Screws. Do this twice so you have 2 Roof Support Assemblies. (fig. 4.1) Fig. 4.1 Wood Parts Hardware Roof Side FSC 1-3/16 x 3-1/4 x 35-7/8”...
  • Page 22 Step 4: Roof Assembly Part 2 B: Place (043) Back Roof Panel and (042) Front Roof Panel on each of the Roof Support Assemblies so the Joist Sides of the Roof Panels are flush to the bottoms of each (041) Roof Side. (fig. 4.2 and 4.3) The (042) Front Roof Panel must overlap the (043) Back Roof Panel and connect tightly.
  • Page 23 Step 4: Roof Assembly Part 3 D: From underneath the Roof Assembly centre 1 Corner Bracket on each Joist and attach with 3 (S13) #6 x 5/8” Pan Screws per bracket as shown in fig. 4.5 and 4.6. View from Underneath Fig.
  • Page 24 Step 4: Roof Assembly Part 4 E: Tight to the Roof Panels attach 1 (044) Top Roof Side Left and 1 (045) Top Roof Side Right to each Roof Sup- port Assembly with 4 (S2) #8 x 1-1/2” Wood Screws per board so the peaks are tight and the bottom of each board is flush to the bottom of each Roof Panel.
  • Page 25 Step 4: Roof Assembly Part 5 F: Place (046) Dormer Cleat over pre-drilled holes in (042) Front Roof Panel, with the longer edge at the bottom and the larger face against the third Siding. (fig. 4.8) G: From underneath the Roof Assembly attach (046) Dormer Cleat to third Siding with 2 (S15) #8 x 1-3/4” Wood Screws.
  • Page 26 Step 5: Roof Dormer Assembly Part 1 A: Place (051) Dormer Roof Panel Left and (052) Dormer Roof Panel Right together as shown in fig. 5.1 and 5.2. Attach top of panels together with 2 (S15) #8 x 1-3/4” Wood Screws. (fig. 5.2) B: Measure 5/8”...
  • Page 27 Step 5: Roof Dormer Assembly Part 2 E: Place Oval Window over Oval Window Pane and align holes. Notice orientation of tabs on Oval Window Pane, make sure the holes in tabs click onto holes on Oval Window. This ensures a snug fit. (Fig 5.6) Place assembled Oval Window in opening of (053) Dormer Front Wall and attach with 4 (S13) #6 x 5/8”...

  • Page 28: Step 6: Counter Assembly

    Step 6: Counter Assembly Part 1 A: Attach 1 (062) Counter Brace flush to the bottom edge of (061) Counter Joist using 1 (S3) #8 x 2-1/2” Wood Screw. Do this four times so you have 4 Counter Joist Assemblies. (fig. 6.1) Fig.
  • Page 29 Step 6: Counter Assembly Part 2 B: Flush to each end and to the bottom of (064) Counter Back attach 1 Counter Joist Assembly per end with 1 (S2) #8 x 1-1/2” Wood Screw per assembly. (fig. 6.2) C: Place the remaining 2 Counter Joist Assemblies centred over the pilot holes in the middle of (064) Counter Back and flush to the bottom of the board, then attach with 1 (S2) #8 x 1-1/2”...
  • Page 30 Step 7: Front Wall Assembly A: Place (073) Top Front Panel on top of (071) Front Left Wall and (072) Front Right Wall so the ends are flush. Attach from the opening in the Front Left and Right Walls with 2 (S26) #8 x 2” Pan Screws. (fig. 7.1) B: Place (075) Front Bottom to the bottom of (071) Front Left Wall and (072) Front Right Wall so the ends are flush with the outside edge of each Wall and attach with 4 (S15) #8 x 1-3/4”...
  • Page 31 Step 8: Window Wall Assembly A: Place (081) Shutter Wall Panel tight to (074) Corner Trim on (071) Front Left Wall so the inside board is flush to the inside edge of (074) Corner Trim. Attach (074) Corner Trim to (081) Shutter Wall Panel with 5 (S26) #8 x 2” Pan Screws.
  • Page 32 Step 9: Back Wall Assembly A: Place (092) Back Wall Panel tight to (074) Corner Trim on (081) Shutter Wall Panel so the inside board is flush to the inside edge of (074) Corner Trim. Attach (074) Corner Trim to (092) Back Wall Panel with 5 (S26) #8 x 2” Pan Screws.
  • Page 33 Step 10: Half Wall Assembly A: Place (101) Half Wall Panel between (072) Front Right Wall and (092) Back Wall Panel so the inside edges are flush to the inside edges of both (074) Corner Trims. Attach (101) Half Wall Panel to both (074) Corner Trims with 3 (S26) #8 x 2”...
  • Page 34 Step 11: Soffit Assembly A: Mark the centre point of both (073) Top Front Panel and (091) Top Back Panel. (fig. 11.1) B: Place 2 (111) Soffit Wides tight together on top of (073) Top Front Panel so the inside edges line up with the marked out spot from Step A.
  • Page 35 Step 12: Attach Roof to Assembly Make sure assembly is square before proceeding in this Step. A: With an adult helper lift the Roof Assembly from Step 4 onto the (111) Soffit Wides so the tips of the (041) Roof Sides are flush to the ends of each (111) Soffit Wide.
  • Page 36 Step 13: Upper Half Wall Assembly Part 1 A: On the Half Wall Side place (131) Cafe Top tight to top of (111) Soffit Wides and attach to (041) Roof Sides with 4 (S2) #8 x 1-1/2” Wood Screws. (fig. 13.1) Fig.
  • Page 37 Step 13: Upper Half Wall Assembly Part 2 B: From inside the assembly place 3 (132) Chalkwall Supports as shown in fig. 13.2, making sure the notched out ends fit around the supports on the inside of (101) Half Wall Panel. The distance between the 2 closest boards should be maintained at 9-1/4”.
  • Page 38 Step 13: Upper Half Wall Assembly Part 3 D: Place (133) Cafe Table Top between 2 (132) Chalkwall Supports so the grooves are tight to each support as shown in fig. 13.4 and 13.5. Attach with 2 (S3) #8 x 2-1/2” Wood Screws per (132) Chalkwall Support. E: On the outside of the assembly centre (134) SL Brace on the underside of (133) Cafe Table Top so it lines up with the pilot holes on (101) Half Wall Panel.
  • Page 39 Step 13: Upper Half Wall Assembly Part 4 F: From inside of the assembly place 2 (136) Cafe Sides over the 2 (132) Chalkwall Supports that surround the (133) Cafe Table Top so the edges are flush to each other. Each (136) Cafe Side should fit tight to both (131) Cafe Top and (133) Cafe Table Top.
  • Page 40 Step 14: Cafe Gable Assembly Part 1 A: From outside of the assembly place 1 (141) Cafe Roof flush to the inside edge of (041) Roof Side with the angled edge at the top. Top of board should align with the peak of the Roof Assembly. Attach (141) Cafe Roof to (041) Roof Side with 3 (S2) #8 x 1-1/2”...
  • Page 41 Step 14: Cafe Gable Assembly Part 2 D: From inside the assembly place (143) Long Cafe Gable tight to top of (131) Cafe Top with arch facing up then attach to (041) Roof Sides with 4 (S2) #8 x 1-1/2” Wood Screws. (fig. 14.5 and 14.6) E: Measure 2-3/4”...
  • Page 42 Step 14: Cafe Gable Assembly Part 3 F: Insert Roof Peak Spinner into slot of Roof Peak Mount. (fig. 14.8) and place Roof Peak Mount in opening above (142) Short Cafe Gable tight to the peak and flush to the bottom of (142) Short Cafe Gable. From inside the assembly attach Roof Peak Mount to (041) Roof Sides with 4 (S13) #6 x 5/8”...
  • Page 43 Step 14: Cafe Gable Assembly Part 4 H: Measure 7/16” in from the outside edges of both (141) Cafe Roofs and place 1 (144) Cafe Gingerbread under each (141) Cafe Roof so the tops meet at the peak. (fig. 14.9 and 14.10) I: Pre-drill with a 1/8”...
  • Page 44 Step 15: Attach Spin Chalk Sign Part 1 A: Place (152) Spin Trim Bottom on (101) Half Wall Panel, between both (132) Chalkwall Supports, so the arches are flush then attach with 2 (S0) #8 x 7/8” Truss Screw. (fig. 15.1 and 15.2) B: Place (151) Spin Trim Top on (131) Cafe Top, between both (132) Chalkwall Supports, so the arches are flush then attach with 2 (S0 or S22) #8 x 7/8”...
  • Page 45 Step 15: Attach Spin Chalk Sign Part 2 C: Place Spin Chalk Sign between (132) Chalkwall Supports and attach with 6 (S13) #6 x 5/8” Pan Screws. (fig. 15.3, 15.4 and 15.5) Fig. 15.3 Spin Chalk Sign Fig. 15.4 Parts removed for clarity. Outside View Fig.
  • Page 46 Step 16: Attach Bench Assembly A: Attach 2 U-Brackets to bottom of (101) Half Wall Panel using 1 (PB6) 1/4 x 1” Pan Bolt (with t-nut) per bracket.(fig. 16.1 and 16.2) B: Place Bench Assembly from Step 2 against (101) Half Wall Panel, and into the U-Brackets. Attach using 1 (H1) 1/4 x 1-1/2”...
  • Page 47 Step 17: Window Wall Gable Assembly Part 1 A: Place Small Gable Vent between the 2 (041) Roof Sides on the Window Wall tight to the peak. From inside the assembly attach Small Gable Vent to (041) Roof Sides with 4 (S13) #6 x 5/8” Pan Screws. (fig. 17.1 and 17.2) Note 6 screws are shown in fig.
  • Page 48 Step 17: Window Wall Gable Assembly Part 2 B: Tight to both (041) Roof Sides place (171) Roof Gable Support and attach to both (041) Roof Sides with 2 (S2) #8 x 1-1/2” Wood Screws. (fig 17.3 and 17.4) C: From inside the assembly attach Small Gable Vent to (171) Roof Gable Support with 2 (S13) #6 x 5/8 Pan Screws.
  • Page 49 Step 17: Window Wall Gable Assembly Part 3 D: Tight to the top of (082) Top Side Panel place (174) Gable Block Long and attach to both (041) Roof Sides with 4 (S2) #8 x 1-1/2” Wood Screws. (fig 17.6) E: Tight to the top of (174) Gable Block Long place (173) Gable Block and attach to both (041) Roof Sides with 4 (S2) #8 x 1-1/2”...
  • Page 50 Step 18: Window Wall Shutter Assembly Part 1 A: Centre (181) Shutter Top over opening in (081) Shutter Wall Panel, flush to the bottom of (082) Top Side Panel, then place (182) Window Arch Assembly centred on top of (181) Shutter Top. (fig. 18.1 and 18.2) B: From inside the assembly attach (082) Top Side Panel to (182) Window Arch Assembly and (081) Shutter Wall Panel to (181) Shutter Top with 4 (S15) #8 x 1-3/4”...
  • Page 51 Step 18: Window Wall Shutter Assembly Part 2 C: Insert the bottom Shutter Pivots in the 2 (031) Shutter Assemblies from Step 3 into (183) Shutter Bottom. (fig. 18.5 and 18.6) D: Tilt assembly and lift up to insert top Shutter Pivots into (181) Shutter Top. Make sure it is snug. (fig. 18.6 and 18.7) E: Make sure (183) Shutter Bottom is square to (181) Shutter Top then from inside the assembly attach (183) Shutter Bottom to (081) Shutter Wall Panel with 2 (S15) #8 x 1-3/4”...
  • Page 52 Step 18: Window Wall Shutter Assembly Part 3 F: Attach 1 (184) Window Trim to each side of the opening in (081) Shutter Wall Panel using 3 (TS) #6 x 30 mm Trim Screws per board. Notice the pilot holes are towards the inside of the assembly. (fig. 18.9 and 18.10) G: Place (185) Shutter Stop tight to top of (183) Shutter Bottom and tight to the panel then attach to (183) Shutter Bottom using 3 (TS) #6 x 30 mm Trim Screws.
  • Page 53 Step 18: Window Wall Shutter Assembly Part 4 H: Attach 1 Dutch Magnetic Catch centred in opening with 2 (S18) #6 x 1” Wood Screw into (185) Shutter Stop. (fig. 18.11) Important: Use a hand held screw driver and DO NOT over tighten. I: Attach 1 Dutch Catch Plate on edge on inside of each Shutter Panels (location shown in fig.
  • Page 54 Step 18: Window Wall Shutter Assembly Part 5 J: Attach 4 (186) Tie Blocks flush to top of (091) Top Back Panel and to (092) Back Wall Panel in the places shown in fig. 18.13 using 2 (S2) #8 x 1-1/2” Wood Screws per (186) Tie Block. K: Attach 2 (186) Tie Blocks flush to top of (082) Top Side Panel and to (081) Shutter Wall Panel in the places shown in fig.

  • Page 55: Step 19: Door Assembly

    Step 19: Door Assembly Part 1 A: On the outside of (191) Dutch Door Top Panel and (192) Dutch Door Bottom Panel attach 4 Door Hinges using 3 (S13) # 6 x 5/8” Pan Screws per Hinge. Judge spacing based on fig. 19.1. B: On the outside of (191) Dutch Door Top Panel and (192) Dutch Door Bottom Panel attach 2 Door Handles as shown in fig.
  • Page 56 Step 19: Door Assembly Part 2 E: In the opening for the door on the Front Wall, measure 5/8” up from the top of (075) Front Bottom then attach remaining side of the Door Hinges on (192) Dutch Door Bottom Panel to (071) Front Left Wall with 3 (S13) #6 x 5/8”...
  • Page 57 Step 19: Door Assembly Part 3 In the notched out opening of (193) Door Latch Block attach the Dutch Magnetic Catch using 2 (S18) #6 x 1” Wood Screws. (fig. 19.5) Important: Use a hand held screw driver and DO NOT over tighten. G: From inside the assembly measure 17-7/8”...
  • Page 58 Step 20: Attach Door Bell Assembly A: On the outside of the assembly attach Doorbell Key to (072) Front Right Wall, in the hole provided with 1 #6 x 9 mm Self Tapping Screw , as shown in fig. 20.1 and 20.2. B: From inside the assembly attach Doorbell to (072) Front Right Wall with 2 (S10) #8 x 1”...
  • Page 59 Step 21: Attach Flower Boxes A: Place 1 Flower Box 2-1/8” below window opening on (071) Front Left Wall measure 1” from the outermost left hand tip of the flower box, to the edge of the face of (081) Shutter Wall Panel then attach with 2 (S10) #8 x 1” Pan Screws.
  • Page 60 Step 22: Attach Windows A: Place 1 Playhouse Window in each window opening on the Front and Back Walls as well as in the (191) Dutch Door Top Panel. There should be 5 Playhouse Windows in total. Attach with 4 (S13) #6 x 5/8” Pan Screws per Playhouse Window.
  • Page 61 Step 23: Attach Roof Dormer Assembly A: Place Roof Dormer Assembly from Step 5 on the Roof Assembly at the (046) Dormer Cleat previously attached. The tip of the Roof Dormer Assembly should be flush to the top of the Roof Assembly. (fig. 23.1) B: Attach Roof Dormer Assembly to (046) Dormer Cleat with 2 (S3) #8 x 2-1/2”...
  • Page 62 Step 24: Attach Dormer Gingerbread A: Place 1 (241) Dormer Gingerbread on each side of the Roof Dormer Assembly so the ends with a 45 degree angle meet at the peak and are flush to the centre of the Roof Dormer Assembly outside face. Pre-drill with a 1/8” drill bit then attach each (241) Dormer Gingerbread to Roof Dormer with 3 (S15) #8 x 1-3/4”...
  • Page 63 Step 25: Attach Counter Assembly Part 1 A: On the inside of the assembly place Counter Assembly from Step 6 against the Back Wall and Half Wall. The top of (063) Counter Front should be flush and level to the top of (133) Cafe Table Top. (fig. 25.1 and 25.2) B: Attach (064) Counter Back to (092) Back Wall Panel with 4 (S2) #8 x 1-1/2”...
  • Page 64 Step 25: Attach Counter Assembly Part 2 D: Tight to (064) Counter Back attach (252) Counter Top to each (061) Counter Joist with 4 (TS) #6 x 30 mm Trim Screws. (fig. 25.3 and 25.4) E: Tight to (252) Counter Top and flush to the outside edges of the outer (061) Counter Joists attach 1 (253) Counter Side per joist with 3 (TS) #6 x 30 mm Trim Screws per board.
  • Page 65 Step 25: Attach Counter Assembly Part 3 G: Place Faucet and 2 Sink Knobs in opening of Sink and attach Sink Knobs with 1 #6 x 10 mm Blunt Point Pan Screw (included in Kitchen Set box) per Sink Knob. (fig. 25.5) H: Loosely attach 4 Mount Clips to the bottom of the Sink and Stove using 1 #6 x 10 mm Blunt Point Pan Screw (included in Kitchen Set box) for each Mount Clip as shown in fig.
  • Page 66 Step 25: Attach Counter Assembly Part 4 I: Place Sink and Stove in the openings of the Counter Assembly then tighten the Mount Clips to secure in place. (fig. 25.7, 25.8 and 25.9) Note: To remove the Sink or Stove loosen screw 1/4 turn then twist Mount Clips. Fig.
  • Page 67 Step 25: Attach Counter Assembly Part 5 J: Flush to the bottom of (091) Top Back Panel attach Utensil Shelf with 2 (S13) #6 x 5/8” Pan Screws. (fig. 25.10 and 25.11) K: Attach Pot, Pan and Spatula to the Utensil Shelf. L: On (132) Chalkwall Support, in approximate location shown in fig.
  • Page 68 Step 26: Attach Playhouse Plaque A: From inside the Playhouse attach Playhouse Plaque to (041) Roof Sides with 2 (S13) #6 x 5/8” Pan Screws as shown in fig. 26.1 and 26.2 Fig. 26.1 Outside View Playhouse Plaque Fig. 26.2 Inside View Hardware Other Parts...
  • Page 69 NOTES support@cedarsummitplay.com...
  • Page 70 NOTES support@cedarsummitplay.com...
  • Page 71 NOTES support@cedarsummitplay.com...
  • Page 72 MAIL TO: Fill out your registration card online at Solowave Design www.cedarsummitplay.com/registration 375 Sligo Road W. Mount Forest, Ontario, Canada Cedar Summit would like to say Thank You for N0G 2L0 your time and feedback. Attention: Customer Service REVISION: 11/28/12...

This manual is also suitable for:

P280068

Table of Contents