Cedar Summit STORYBROOKE PLAYHOUSE P280070 Installation And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Cedar Summit Manuals
  4. Play Sets & Playground Equipment
  5. STORYBROOKE PLAYHOUSE P280070
  6. Installation and operating instructions manual

Cedar Summit STORYBROOKE PLAYHOUSE P280070 Installation And Operating Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

S T O RY B R O O K E P L AY H O U S E – P 2 8 0 0 7 0

INSTALLATION AND OPERATING INSTRUCTIONS

5'6"
3 - 5 Hrs
TWO PERSON
ASSEMBLY
Rev 10/24/2014
9400070
WARNING
play set. Manufacturer contact information provided below.
CAPACITY - 5 Users Maximum, Ages 2 to 10.
4'2"
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries,
day cares or parks.
Cedar Summit
c/o ©Solowave Design L.P.
Mount Forest, ON Canada
N0G 2L0
www.cedarsummitplay.com
support@cedarsummitplay.com
Customer Service
1-877-817-5682 (toll free)
1-519-323-2258
To reduce the risk of serious injury or death, you must
read and follow these instructions. Keep and refer to these
instructions often and give them to any future owner of this

Table of Contents

Warnings And Safe Play Instructions . . . . . . . . . . .pg. 2
Instructions For Proper Maintenance . . . . . . . . . . .pg. 2
Keys To Assembly Success . . . . . . . . . . . . . . . . . . . . .pg. 3
About Our Wood – Limited Warranty. . . . . . . . . . .pg. 4
Keys to Quick Assembly . . . . . . . . . . . . . . . . . . . . . . .pg. 5
Part ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .pg. 6
Step-By-Step Instructions . . . . . . . . . . . . . . . . . . . . pg. 13
Installation of I.D./Warning Plaque . . . . . . . .Final Step

Advertisement

Table of Contents
loading

Related Manuals for Cedar Summit STORYBROOKE PLAYHOUSE P280070

Summary of Contents for Cedar Summit STORYBROOKE PLAYHOUSE P280070

  • Page 1 3 - 5 Hrs TWO PERSON ASSEMBLY Table of Contents Cedar Summit c/o ©Solowave Design L.P. Warnings and Safe Play Instructions ...pg. 2 Mount Forest, ON Canada Instructions for Proper Maintenance ...pg. 2 N0G 2L0 Keys to Assembly Success .
  • Page 2 Instructions for Proper Maintenance Your Cedar Summit Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Playhouse, it is important that you, the owner, properly maintain it.
  • Page 3 Keys to Assembly Success Tools Required • Tape Measure • #1 & #2 Phillips or • Open End Wrench • Safety Glasses • Carpenters Level Robertson bits (7/16”) • Adult Helpers • Carpenters Square • Ratchet with extension • Adjustable Wrench •...
  • Page 4 About Our Wood Cedar Summit Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s use. Although we take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible to weathering which can change the appearance of your set.
  • Page 5 Your Key To Quick Assembly SORTING WOOD PARTS INTO EACH ASSEMBL Y STEP WILL SAVE TIME! Step Step Step SAVE TIME - TIP #1: Open box with wood parts and look for the Key Number stamped on the end of the wood part (see chart below). Sort each wood part into the different assembly steps.
  • Page 6 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) 48046736 4pc. - 110 - 12.7 x 57.2 x 1063.6 - Corner Trim FSC - (1/2 x 2-1/4 x 41-7/8") 48055004 4pc.
  • Page 7 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) 48056036 4pc. - 095 - 15.9 x 85.7 x 177.8 - Gable End E FSC - (5/8 x 3-3/8 x 7") 2pc.
  • Page 8 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) 478056336 1pc. - 021 - 31.8 x 911.2 x 1136.7mm - Roof Panel FSC - (1-1/4 x 35-7/8 x 44-3/4") 478056836 1pc.
  • Page 9 Hardware Identification (Actual Size) 4pc. FW1 - 1/4" Flat Washer - (51103200) 4pc. LW1 - 1/4" Lock Washer - (51303200) 4pc. TN1 - 1/4" T - Nut (54503200) #6 x 5/8" 61pc. S13 - Pan Screw - (52413908) #6 x 1" 16pc.
  • Page 10 Part Identification (Reduced Part Size) 1x - Playhouse Plaque (9320360) 1x - Twist Door Bell Set (3320934) 1x - Deluxe Kitchen Set (3320969) 1x - Stove (3320784) 2x - Deep Window (3Pk) (3323539) White 1x - Utensils Shelf (9320791) 1x - Pot Pan Spatula (9320889) 10x - #6 x 10mm Blunt Point Pan Screw...
  • Page 11 support@cedarsummitplay.com...
  • Page 12 support@cedarsummitplay.com...
  • Page 13 Step 1: Inventory Parts - Read This Before Starting Assembly STOP STOP STOP STOP This is the time for you to inventory all your hardware, wood and accessories, referencing the parts identification sheets. This will assist you with your assembly. •...
  • Page 14 Step 2: Roof Assembly Part 1 A: Flush to the bottom of (021) Roof Panel attach 1 (023) Roof Panel Side using 4 (S3) #8 x 2-1/2” Wood Screws. Make sure (023) Roof Panel Side is tucked in under the siding overhang. This will help prevent leaks when it rains.
  • Page 15 Step 2: Roof Assembly Part 2 B: From underneath the Roof Assembly centre 1 Narrow Angle Bracket on each inside joist and attach with 2 (S13) #6 x 5/8” Pan Screws per bracket. (fig. 2.3 and 2.4) Narrow Angle Bracket Fig.
  • Page 16 Step 2: Roof Assembly Part 3 C: Attach 1 (024) Roof Side to another flush at the peak using 1 (S3) #8 x 2-1/2” Wood Screw. Do this twice so you have 2 Roof Support Assemblies. (fig. 2.5) Fig. 2.5 Wood Parts Hardware #8 x 2-1/2”...
  • Page 17 Step 2: Roof Assembly Part 4 D: Place 1 Roof Side Assembly on each end of the Roof Assembly so the peaks fit together and the outside face of each (024) Roof Side is flush to the outside face and bottoms of the joists. (fig. 2.6 and 2.7) E: Attach each Roof Side Assembly to the Roof Panels with 6 (S15) #8 x 1-3/4”...
  • Page 18 Step 3: Counter Assembly Part 1 A: Flush to each end and to the bottom of (031) Counter Back attach 1 (033) Counter Joist per end with 1 (S2) #8 x 1-1/2” Wood Screw per joist. Notice the holes at the top of (031) Counter Back. (fig. 3.1 and 3.2) B: Place the remaining 3 (033) Counter Joists centred over the pilot holes in the middle of (031) Counter Back and flush to the bottom of the board, then attach, in the bottom holes, with 1 (S2) #8 x 1-1/2”...
  • Page 19 Step 3: Counter Assembly Part 2 D: Place 1 (034) Counter Brace tight to the bottom of each outside (033) Counter Joist, tight to (032) Counter Front and attach using 1 (S3) #8 x 2-1/2” Wood Screw per brace. (fig. 3.3 and 3.4) E: Place (035) Counter Brace Centre tight to the bottom of the centre (033) Counter Joist, tight to (032) Counter Front and attach using 1 (S3) #8 x 2-1/2”...
  • Page 20 Step 4: Frame Assembly Part 1 A: Stand (040) Panel Assembly up so window openings are at the top then with a helper at the opposite end open (040) Panel Assembly all the way so corners are at a 90 degree angle. (fig. 4.1 and 4.2) Fig.
  • Page 21 Step 4: Frame Assembly Part 2 B: Flush to the inside face of the Side Wall and Cafe Wall place 1 (041) Soffit Side centred in each opening and attach with 4 (S2) #8 x 1-1/2” Wood Screws per board. Notice the holes are towards the inside of the frame. (fig. 4.3) C: On the Door Wall and Back Wall, tight to each (041) Soffit Side and flush to the inside face of each wall attach 2 (042) Soffit Front Backs to each wall with 2 (S2) #8 x 1-1/2”...
  • Page 22 Step 4: Frame Assembly Part 3 E: Flush to the bottom and centred on the Side Wall and Cafe Wall attach 1 (043) Panel Tie to each wall with 4 (S15) #8 x 1-3/4” Wood Screws per board. (fig. 4.4, 4.5 and 4.6) Fig.
  • Page 23 Step 5: Cafe Wall Assembly Part 1 A: Place (051) Cafe Table Top in large opening of Cafe Wall so the grooves are tight to the wall and attach with 2 (S15) #8 x 1-3/4” Wood Screws in the outside holes. (fig. 5.1 and 5.2) B: Centred and tight to the bottom of (051) Cafe Table Top attach (043) Panel Tie to Cafe Wall with 4 (S15) #8 x 1-3/4”...
  • Page 24 Step 5: Cafe Wall Assembly Part 2 D: From inside the assembly, centred in the large opening of the Cafe Wall attach Utensil Shelf with 2 (S13) #6 x 5/8” Pan Screws as shown in fig. 5.3, 5.4 and 5.5. E: Attach Pot, Pan and Spatula to the Utensil Shelf.
  • Page 25 Step 6: Attach Door Panel Accessories Part 1 A: Measure 18-1/4” up from the bottom of the Door on the outside and inside and attach 1 Door Handle per side using 2 (S13) # 6 x 5/8” Pan Screws per handle. (fig. 6.1 and 6.2) B: Measure 15”...
  • Page 26 Step 6: Attach Door Panel Accessories Part 2 C: In the notched out opening of (061) Door Latch Block Fig. 6.4 attach the Magnetic Catch using 2 (S18) #6 x 1” Wood Inside View Screws. (fig. 6.3 and 6.4) Important: Use a hand held screw driver and DO NOT over tighten.
  • Page 27 Step 7: Attach Counter Assembly Part 1 A: On the inside of the playhouse assembly place Counter Assembly from Step 3 against the Cafe Wall. The top of (031) Counter Back should be flush and level to the bottom of (051) Cafe Table Top. (fig. 7.1 and 7.2) B: Attach (031) Counter Back to Cafe Wall with 4 (S2) #8 x 1-1/2”...
  • Page 28 Step 7: Attach Counter Assembly Part 2 D: Tight to (031) Counter Back attach (071) Counter Top to each (033) Counter Joist with 5 (TS) #6 x 30 mm Trim Screws. (fig. 7.3) E: Tight to (071) Counter Top and flush to the outside edges of the outer (033) Counter Joists attach 1 (072) Counter Side per joist with 3 (TS) #6 x 30 mm Trim Screws per board.
  • Page 29 Step 7: Attach Counter Assembly Part 3 G: Place Faucet and 2 Sink Knobs in opening of Sink and attach Sink Knobs with included hardware. (fig. 7.4) Important: Use a hand held screw driver and DO NOT over tighten. Fig. 7.4 Faucet Sink Knob Sink Knob...
  • Page 30 Step 7: Attach Counter Assembly Part 4 H: Place Sink and Stove in the openings of the Counter Assembly then attach 4 Mount Clips with included hardware to the bottom of the Sink and Stove to secure in place. (fig. 7.5 and 7.6) Important: Use a hand held screw driver and DO NOT over tighten.
  • Page 31 Step 8: Attach Roof to Assembly Make sure assembly is square before proceeding in this Step. A: With an adult helper lift the Roof Assembly from Step 2 onto the (041) Soffit Sides and (042) Soffit Front Back so the notches in each (023) Roof Panel Side fit tight to the ends of each (042) Soffit Front Back. The opening should face the Door and Back Walls (fig.
  • Page 32 Step 9: Gable Assembly Part 1 A: From inside the assembly, tight to the Roof Assembly and centred at the peak, attach 2 (091) Gable End A with 2 (S2) #8 x 1-1/2” Wood Screws per board. (fig. 9.1 and 9.2) B: Tight to each (091) Gable End A and tight to the Roof Assembly attach 2 (092) Gable End B with 4 (S2) #8 x 1-1/2”...
  • Page 33 Step 9: Gable Assembly Part 2 D: From outside the assembly, flush to the inside edge of each (092) Gable End B and tight to (042) Soffit Front Back, attach 2 (096) Shutter Sides with 2 (S18) #6 x 1” Wood Screws per board. (fig. 9.3 and 9.4) E: Flush to the bottom of each (091) Gable End A in between (096) Shutter Sides attach 1 (097) Shutter Top with 2 (S18) #6 x 1”...
  • Page 34 Step 9: Gable Assembly Part 3 F: Centred at the peak and flush to the top of the Roof Assembly, attach 2 (098) Roof Side Tops with 3 (TS) #6 x 30 mm Trim Screws per board. (fig. 9.5 and 9.6) G: Tight to the bottom of each (098) Roof Side Top attach 1 (099) Roof Side Bottom with 3 (TS) #6 x 30 mm Trim Screws per board.
  • Page 35 Step 10: Shutter Assembly Part 1 A: Place 1 Door Handle on the front of each (100) Shutter Assembly centred over 1 panel as shown in fig. 10.1 and 10.2. Attach with 2 (S13) #6 x 5/8” Pan Screws per handle. B: On the opposite side as the Door Handles attach 2 Shutter Pivots to each (100) Shutter Assembly using provided hardware, as shown in fig.
  • Page 36 Step 10: Shutter Assembly Part 2 D: Below the opening in the Side Wall place 1 (101) Shutter Top Bottom flush to the bottom of the opening and attach from the inside with 2 (S15) #8 x 1-3/4” Wood Screws. Notice the holes are towards the outside of the board.
  • Page 37 Step 10: Shutter Assembly Part 3 G: Insert the bottom Shutter Pivots of each (100) Shutter Assembly into (101) Shutter Top Bottom. (fig. 10.6 and 10.7) H: Insert the top Shutter Pivots in 1 (101) Shutter Top Bottom and hold against the Side Wall making sure the (100) Shutter Assemblies are level and open without issue.
  • Page 38 Step 11: Attach Corner Trim A: Flush to the outside edges and bottom of the Cafe Wall attach 2 (110) Corner Trims with 6 (TS) #6 x 30 mm Trim Screws per board. (fig. 11.1 and 11.2) Repeat Step A for Side Wall. Notice hole orientation Fig.
  • Page 39 Step 12: Attach Windows A: Place 1 Deep Window in each window opening on the Door Wall and Back Wall. There should be 7 Deep Windows in total, 4 on the Door Wall and 3 on the Back Wall. Attach each window with 4 (S13) #6 x 5/8” Pan Screws.
  • Page 40 Step 13: Attach Flower Boxes A: Place 1 Flower Box under each side Window on the Door Wall and attach with 2 (S10) #8 x 1” Pan Screws per Flower Box. (fig. 13.1 and 13.2) Fig. 13.1 Fig. 13.2 x 2 per Flower Box Door Wall Flower Box Hardware...
  • Page 41 Step 14: Bench Assembly A: Open the (140) Folding Bench Assembly. (fig. 14.1, 14.2 and 14.3) B: Make sure assembly is level then secure with 2 (H1) 1/4 x 1-1/2” Hex Bolts (with lock washer, flat washer and t-nut) per side. (fig. 14.4) C: Tighten the top screws in all 4 Bench Legs.
  • Page 42 Step 15: Attach Playhouse Plaque A: On the Back Wall above the top Deep Window install the Playhouse Plaque with 2 (S13) #6 x 5/8” Pan Screws. (fig. 15.1 and 15.2) Playhouse Plaque Fig. 15.2 Fig. 15.1 Back Wall Hardware Other Parts 1 x Playhouse Plaque #6 x 5/8”...
  • Page 43 NOTES support@cedarsummitplay.com...
  • Page 44 MAIL TO: Fill out your registration card online at Solowave Design www.cedarsummitplay.com/registration 375 Sligo Road W. Mount Forest, Ontario, Canada Cedar Summit would like to say Thank You for N0G 2L0 your time and feedback. Attention: Customer Service REVISION: 11/28/12...

Table of Contents