Advertisement
Quick Links
Installation, Maintenance & Parts Manual
MODELS 304 & 310
Cleated Belt
Incline Conveyors
For Additional copies of this manual, please visit our website at
www.titanconveyors.com
Go to Info Center, Select the Maintenance Manual Tab
and select the manual for your model conveyor
or click on the link below.
https://www.titanconveyors.com/info-center#823236-maintenance-manuals
735 Industrial Loop Road
New London, WI 54961
E-mail: sales@titanconveyors.com
Website: www.titanconveyors.com
Serial No.
Go to Table of Contents
Industrial Conveyor Specialists
For
Titan Conveyors
920-982-6600
800-558-3616
FAX 920-982-7750
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Titan 304
Summary of Contents for Titan 304
- Page 1 Industrial Conveyor Specialists Installation, Maintenance & Parts Manual MODELS 304 & 310 Cleated Belt Incline Conveyors For Additional copies of this manual, please visit our website at www.titanconveyors.com Go to Info Center, Select the Maintenance Manual Tab and select the manual for your model conveyor or click on the link below.
- Page 2 Buyer establishes to the seller’s satisfaction that any part or parts manufactured by TITAN were defective at the time of shipment, TITAN will, at its own expense, repair or replace (but not install) replacement parts. For a time purpose of this warranty, one year will constitute 2080 hours of operation based on an 8 hour day.
- Page 3 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
-
Page 4: Installation
Titan at 920-982-6600. I. RECEIVING Upon delivery of your Titan conveyor, check the packing slip or bill of lading accompanying the unit. If any components are missing, contact Titan IMMEDIATELY with a description of the missing components along with the conveyor serial number(s). - Page 5 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 6 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 7 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S Belt Threading MODEL 304 CLEATED BELT CONVEYOR BELT TRAVEL MODEL 310...
-
Page 8: Maintenance
1. The first step in belt tracking is to make sure all pulleys are parallel with each other and perpendicular to the frame. Once this has been done refer to FIGURE 7 for proper tracking adjustments on end drive conveyors. IN REF. TO LEFT HAND AND RIGHT HAND SIDES, WE AT TITAN INDUSTRIES CAUTION... - Page 9 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 10 2. VENTILATION - During normal operation gear reducers build up heat and pressure that MUST be vented to protect the seals and gears. If not installed at Titan, a brass vent plug contained in a small plastic bag, will be put in a box or larger bag along with fasteners sent loose for use during field installation.
- Page 11 ONLY compatible polyglycol lubricants should be used. Contact the factory for more information. TEMPERATURE - Most Titan Units are supplied with wormgear reducers. These units may run at temperatures between 100 degrees to 200 degrees F. (Higher temperatures are especially common during start up). There is NO NEED TO WORRY unless temperatures exceed 200 degrees F.
- Page 12 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 13 SHUT OFF CONVEYOR BEFORE USING OIL CAN OR BRUSH TO APPLY OIL! REMEMBER - ALL GUARDS AND BOTTOM PANS, IF PROVIDED, MUST BE REPLACED BEFORE RUNNING CONVEYOR. TITAN INDUSTRIES IS NOT DANGER RESPONSIBLE FOR INjURIES CAUSED BY NOT COMPLYING WITH SAFETY INSTRUCTIONS.
- Page 14 V E Y O R S V E Y O R S V E Y O R S V E Y O R S MODEL 304 CLEATED BELT PARTS CONVEYOR MODEL 304 PARTS CONVEYOR OPT. HOPPER SUPPORTS 1. MOTOR BASE 12.
- Page 15 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
Need help?
Do you have a question about the 304 and is the answer not in the manual?
Questions and answers