Advertisement
Quick Links
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
Installation, Maintenance & Parts Manual
SLIDER BED CONVEYORS
MODELS 104 & 108
For Additional copies of this manual, please visit our website at
www.titanconveyors.com
Go to Info Center, Select the Maintenance Manual Tab
and select the manual for your model conveyor
or click on the link below.
https://www.titanconveyors.com/info-center#823236-maintenance-manuals
735 Industrial Loop Road
New London, WI 54961
E-mail: sales@titanconveyors.com
Website: www.titanconveyors.com
Serial No.
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
Go to Table of Contents
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
Industrial Conveyor Specialists
For
Titan Conveyors
920-982-6600
800-558-3616
FAX 920-982-7750
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
1
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
12/22
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Titan 104
Summary of Contents for Titan 104
- Page 1 V E Y O R S Industrial Conveyor Specialists Installation, Maintenance & Parts Manual SLIDER BED CONVEYORS MODELS 104 & 108 For Additional copies of this manual, please visit our website at www.titanconveyors.com Go to Info Center, Select the Maintenance Manual Tab and select the manual for your model conveyor or click on the link below.
- Page 2 Page 17 ......Model 108 Center Driive & Take-up Blow Apart Drawing (A) Seller warrants that the material in and the workmanship on the equipment manufactured by TITAN will be free from defects at time of shipment. If during the first year from the date of shipment, the Buyer establishes to the seller’s satisfaction that any part or parts manu- factured by TITAN were defective at the time of shipment, TITAN will, at its own expense, repair or replace (but not install) replacement parts.
- Page 3 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 4 Titan at 920-982-6600. I. RECEIVING Upon delivery of your Titan conveyor, check the packing slip or bill of lading accompanying the unit. If any components are missing, contact Titan IMMEDIATELY with a description of the missing components along with the conveyor serial number(s).
- Page 5 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 6 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 7 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 8 Once this has been done refer to FIGURE 7 for proper tracking adjustments on end drive conveyors or FIGURE 8 for proper tracking on center drive and take-up conveyors. IN REF. TO LEFT HAND AND RIGHT HAND SIDES, WE AT TITAN INDUSTRIES CAUTION...
- Page 9 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 10 2. VENTILATION - During normal operation gear reducers build up heat and pressure that MUST be vented to protect the seals and gears. If not installed at Titan, a brass vent plug contained in a small plastic bag, will be put in a box or larger bag along with fasteners sent loose for use during field installation.
- Page 11 ONLY compatible polyglycol lubricants should be used. Contact the factory for more information. TEMPERATURE - Most Titan Units are supplied with wormgear reducers. These units may run at temperatures between 100 degrees to 200 degrees F. (Higher temperatures are especially common during start up). There is NO NEED TO WORRY unless temperatures exceed 200 degrees F.
- Page 12 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 13 SHUT OFF CONVEYOR BEFORE USING OIL CAN OR BRUSH TO APPLY OIL! REMEMBER - ALL GUARDS AND BOTTOM PANS, IF PROVIDED, MUST BE REPLACED BEFORE RUNNING CONVEYOR. TITAN INDUSTRIES IS NOT DANGER RESPONSIBLE FOR INjURIES CAUSED BY NOT COMPLYING WITH SAFETY INSTRUCTIONS.
- Page 14 V E Y O R S V E Y O R S V E Y O R S V E Y O R S Model 104 Slider Bed Belt Conveyor 12/22 V E Y O R S V E Y O R S...
- Page 15 V E Y O R S V E Y O R S V E Y O R S V E Y O R S MODEL 104 SLIDER BED CONVEYOR MODEL 104 SLIDER BED CONVEYOR CENTER DRIVE & TAKE-UP CENTER DRIVE & TAKE-UP SNUB ROLLER LARGE GUARD C.D.
- Page 16 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 17 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
Need help?
Do you have a question about the 104 and is the answer not in the manual?
Questions and answers