Table of Contents
Advertisement
Quick Links
Industrial Conveyor Specialists
Installation, Maintenance & Parts Manual
For
MODELS 610 - 620 - 630
Hinged Steel Belt Conveyors
to View the Instructional Videos
"Setting Tension on a Hinged Steel Belt"
https://youtu.be/7Za3vqVwjvE
"Installing a Hinged Steel Belt Conveyor"
https://youtu.be/HliE9lGVIBM
Titan Conveyors
735 Industrial Loop Road
New London, WI 54961
920-982-6600
800-558-3616
FAX 920-982-7750
E-mail: sales@titanconveyors.com
Website: www.titanconveyors.com
Serial No.
Go to Table of Contents
Advertisement
Table of Contents
Related Manuals for Titan 610
Summary of Contents for Titan 610
- Page 1 Industrial Conveyor Specialists Installation, Maintenance & Parts Manual MODELS 610 - 620 - 630 Hinged Steel Belt Conveyors to View the Instructional Videos "Setting Tension on a Hinged Steel Belt" https://youtu.be/7Za3vqVwjvE "Installing a Hinged Steel Belt Conveyor" https://youtu.be/HliE9lGVIBM Titan Conveyors...
-
Page 2: Table Of Contents
Buyer establishes to the seller’s satisfaction that any part or parts manufactured by TITAN were defective at the time of shipment, TITAN will, at its own expense, repair or replace (but not install) replacement parts. For a time purpose of this warranty, one year will constitute 2080 hours of operation based on an 8 hour day. - Page 3 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
-
Page 4: Introduction
Titan at 920-982-6600. I. RECEIVING Upon delivery of your Titan conveyor, check the packing slip or bill of lading accompanying the unit. If any components are missing, contact Titan IMMEDIATELY with a description of the missing components along with the conveyor serial number(s). -
Page 5: Support Assembly
V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S TITAN CONVEYORS TITAN CONVEYORS J3247 J3247 CONVEYOR: CONVEYOR:... -
Page 6: Belt Checklist
V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S... - Page 7 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
-
Page 8: Component Checklist
V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S... -
Page 9: Motors
V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S... - Page 10 VENTILATION - During normal operation gear reducers build up heat and pressure that MUST be vented to protect the seals and gears. If not installed at Titan, a brass vent plug contained in a small plastic bag, will be put in a box or larger bag along with fasteners sent loose for use during field installation.
-
Page 11: Bearings
ONLY compatible polyglycol lubricants should be used. Contact the factory for more information. TEMPERATURE - Most Titan units are supplied with worm gear reducers. These units may run at temperatures between 100 degrees to 200 degrees F. (Higher temperatures are especially common during start up). There is NO NEED TO WORRY unless temperatures exceed 200 degrees F. -
Page 12: V-Belt & Sheaves
V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S... - Page 13 V E Y O R S V E Y O R S V E Y O R S V E Y O R S MODEL 610 MODEL 610 CHIP CONVEYOR HINGED STEEL BELT CONVEYOR CONVEYOR 13. LOWER CURVE 25. DRIVE GUARD HINGED PLATE 14.
- Page 14 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 15 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...