Advertisement
Quick Links
Industrial Conveyor Specialists
Installation, Maintenance & Parts Manual
For
MODEL 305
Wire Mesh Belt Parts Conveyor
For Additional copies of this manual, please visit our website at
www.titanconveyors.com
Go to Info Center, Select the Maintenance Manual Tab
and select the manual for your model conveyor
or click on the link below.
https://www.titanconveyors.com/info-center#823236-maintenance-manuals
Titan Conveyors
735 Industrial Loop Road
New London, WI 54961
920-982-6600
800-558-3616
FAX 920-982-7750
E-mail: sales@titanconveyors.com
Website: www.titanconveyors.com
Serial No.
Go to Table of Contents
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Titan 305
Summary of Contents for Titan 305
- Page 1 Industrial Conveyor Specialists Installation, Maintenance & Parts Manual MODEL 305 Wire Mesh Belt Parts Conveyor For Additional copies of this manual, please visit our website at www.titanconveyors.com Go to Info Center, Select the Maintenance Manual Tab and select the manual for your model conveyor or click on the link below.
- Page 2 (D) No representative of TITAN has been conferred with any authority to waive, alter, vary or add to the terms of warranty state herein, without prior authorization in writing executed by an officer of the company.
- Page 3 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 4 Titan at 920-982-6600. I. RECEIVING Upon delivery of your Titan conveyor, check the packing slip or bill of lading accompanying the unit. If any components are missing, contact Titan IMMEDIATELY with a description of the missing components along with the conveyor serial number(s).
- Page 5 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 6 Check that sprockets with chain and/or sheaves with V-belt are aligned and properly tensioned.* *Additional information available in section III Maintenance. BELT INSTALLATION MODEL 305 Locate all take-up pulleys to their minimum take-up positions to allow for easy belt installation. Belt Threading As a double check, lay out belt on a level surface and pull tight.
- Page 7 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 8 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 9 2. VENTILATION - During normal operation gear reducers build up heat and pressure that MUST be vented to protect the seals and gears. If not installed at Titan, a brass vent plug contained in a small plastic bag, will be put in a box or larger bag along with fasteners sent loose for use during field installation. Remove the top most drain plug (refer to FIGURE 8) for the position of your reducer) and install the vent plug securely in place.
- Page 10 ONLY compatible polyglycol lubricants should be used. Contact the factory for more information. TEMPERATURE - Most Titan Units are supplied with wormgear reducers. These units may run at temperatures between 100 degrees to 200 degrees F. (Higher temperatures are especially common during start up).
- Page 11 V E Y O R S BEARINGS LUBRICATION - Bearings used on Titan Conveyors are normally pre-lubed for life. If customer requested, re-lube bearings are provided, the use of a #2 consistency lithium based grease is advised. Greasing Frequency should be as many times as necessary to maintain a small film of grease leaking at the seals.
- Page 12 120 degrees - 140 degrees F SAE 50 REMEMBER - ALL GUARDS AND BOTTOM PANS, IF PROVIDED, MUST BE DANGER REPLACED BEFORE RUNNING CONVEYOR. TITAN INDUSTRIES IS NOT RESPONSIBLE FOR INJURIES CAUSED BY NOT COMPLYING WITH SAFETY INSTRUCTIONS. 4/19 V E Y O R S...
- Page 13 V E Y O R S V E Y O R S V E Y O R S V E Y O R S MODEL 305 MODEL 305 WIRE MESH BELT PARTS CONVEYOR WIRE MESH BELT PARTS CONVEYOR OPT. HOPPER SUPPORTS 13. INFEED RETAINER CHANNEL SHAFT COLLAR 1.
Need help?
Do you have a question about the 305 and is the answer not in the manual?
Questions and answers