Advertisement
Quick Links
Installation, Maintenance & Parts Manual
MODEL 402 - 404 - 408
Belt Driven Roller Conveyor
For Additional copies of this manual, please visit our website at
www.titanconveyors.com
Go to Info Center, Select the Maintenance Manual Tab
and select the manual for your model conveyor
or click on the link below.
https://www.titanconveyors.com/info-center#823236-maintenance-manuals
735 Industrial Loop Road
New London, WI 54961
E-mail: sales@titanconveyors.com
Website: www.titanconveyors.com
Serial No.
Go to Table of Contents
Industrial Conveyor Specialists
For
Titan Conveyors
920-982-6600
800-558-3616
FAX 920-982-7750
Advertisement
Related Manuals for Titan 404
Summary of Contents for Titan 404
- Page 1 Industrial Conveyor Specialists Installation, Maintenance & Parts Manual MODEL 402 - 404 - 408 Belt Driven Roller Conveyor For Additional copies of this manual, please visit our website at www.titanconveyors.com Go to Info Center, Select the Maintenance Manual Tab and select the manual for your model conveyor or click on the link below.
- Page 2 Page 18 ....... Model 408 Center Drive and Take up Blow Apart Drawing (A) Seller warrants that the material in and the workmanship on the equipment manufactured by TITAN will be free from defects at time of shipment. If during the first year from the date of shipment, the Buyer establishes to the seller’s satisfaction that any part or parts manu- factured by TITAN were defective at the time of shipment, TITAN will, at its own expense, repair or replace (but not install) replacement parts.
- Page 3 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 4 Titan at 920-982-6600. I. RECEIVING Upon delivery of your Titan conveyor, check the packing slip or bill of lading accompanying the unit. If any components are missing, contact Titan IMMEDIATELY with a description of the missing components along with the conveyor serial number(s).
- Page 5 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 6 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 7 V E Y O R S V E Y O R S V E Y O R S Belt Threading Chart BELT TRAVEL PRODUCT FLOW MODEL 402/404 BELT TRAVEL PRODUCT FLOW MODEL 402/404 CENTER DRIVE & TAKE UP BELT TRAVEL...
- Page 8 Once this has been done refer to FIGURE 7 for proper tracking adjustments on end drive conveyors or FIGURE 8 for proper tracking on center drive and take-up conveyors. IN REF. TO LEFT HAND AND RIGHT HAND SIDES, WE AT TITAN INDUSTRIES CAUTION...
- Page 9 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 10 2. VENTILATION - During normal operation gear reducers build up heat and pressure that MUST be vented to protect the seals and gears. If not installed at Titan, a brass vent plug contained in a small plastic bag, will be put in a box or larger bag along with fasteners sent loose for use during field installation.
- Page 11 ONLY compatible polyglycol lubricants should be used. Contact the factory for more information. TEMPERATURE - Most Titan Units are supplied with wormgear reducers. These units may run at temperatures between 100 degrees to 200 degrees F. (Higher temperatures are especially common during start up). There is NO NEED TO WORRY unless temperatures exceed 200 degrees F.
- Page 12 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 13 SHUT OFF CONVEYOR BEFORE USING OIL CAN OR BRUSH TO APPLY OIL! REMEMBER - ALL GUARDS AND BOTTOM PANS, IF PROVIDED, MUST BE REPLACED BEFORE RUNNING CONVEYOR. TITAN INDUSTRIES IS NOT DANGER RESPONSIBLE FOR INjURIES CAUSED BY NOT COMPLYING WITH SAFETY INSTRUCTIONS.
- Page 14 V E Y O R S V E Y O R S V E Y O R S V E Y O R S MODEL 402-404 BELT DRIVEN MODEL 402 - 404 BELT DRIVEN ROLLER CONVEYOR ROLLER CONVEYOR Belt Travel Product...
- Page 15 V E Y O R S V E Y O R S V E Y O R S MODEL 402/404 BELT DRIVEN ROLLER MODEL 402 - 404 Center Drive & Take-up CENTER DRIVE & TAKE-UP Belt Driven Roller Conveyor 1. LARGE GUARD C.D.& T.U.
- Page 16 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
- Page 17 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...