Related Manuals for Avalue Technology VMS-RPPS
Summary of Contents for Avalue Technology VMS-RPPS
- Page 1 VMS-RPPS Intel® 13th Rugged Fanless Vehicle Telematics System Quick Reference Guide Ed –03 January 2025 Copyright Notice Copyright © 2025 Avalue Technology Inc., ALL RIGHTS RESERVED. Part No. E2017HAS1A0R...
- Page 2 VMS-RPPS Document Amendment History Revision Date Comment January 2025 Avalue Initial Release 2 VMS-RPPS Quick Reference Guide...
-
Page 3: Declaration Of Conformity
For detailed information, please always refer to the electronic user's manual. Copyright Notice © 2025 by Avalue Technology Inc. All rights are reserved. No parts of this manual may be copied, modified, or reproduced in any form or by any means for commercial use without the prior written permission of Avalue Technology Inc. - Page 4 ㆍDescription of your software (operating system, version, application software, etc.) ㆍA complete description of the problem ㆍThe exact wording of any error messages To receive the latest version of the user’s manual; please visit our Web site at: www.avalue.com 4 VMS-RPPS Quick Reference Guide...
- Page 5 On the other hand, if the new product defect is resulting from incorrect configuration or erroneous use by the user instead of any problem of the hardware itself, the customer will also be requested to pay for relevant handling fees. VMS-RPPS Quick Reference Guide...
- Page 6 Lacking detailed statement of fault steps also makes the problem hard to be identified, sometimes resulting in second-time repairs. 6 VMS-RPPS Quick Reference Guide...
- Page 7 Product has been altered or its label of the serial number has been torn off. • Product functionality issues resulting from improper use by the user, unauthorized dismantle or alteration, unfit operation environment, improper maintenance, accident VMS-RPPS Quick Reference Guide...
- Page 8 If the customer demands an additional maintenance analysis report, a service fee of various level will be charged depending on the warranty status. In case the analysis result shows that the defect attributes to Avalue’s faulty design or process, the analysis fee will be exempted. 8 VMS-RPPS Quick Reference Guide...
-
Page 9: Safety Instructions
9. Position the power cord so that people cannot step on it. Do not place anything over the power cord. 10. All cautions and warnings on the equipment should be noted. 11. If the equipment is not used for a long time, disconnect it from the power source to VMS-RPPS Quick Reference Guide... - Page 10 The equipment has obvious signs of breakage. 14. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. 15. Equipment intended only for use in a RESTRICTED ACCESS AREA. 10 VMS-RPPS Quick Reference Guide...
-
Page 11: Explanation Of Graphical Symbols
A NOTE provides additional information intended to avoid Note inconveniences during operation. Direct current. Alternating current Stand-by, Power on FCC Certification CE Certification Follow the national requirements for disposal of equipment. Stacking layer limit This side up VMS-RPPS Quick Reference Guide 11... - Page 12 VMS-RPPS Fragile Packaging Beware of water damage, moisture-proof Carton recyclable Handle with care Follow operating instructions of consult instructions for use. 12 VMS-RPPS Quick Reference Guide...
-
Page 13: Disposing Of Your Old Product
EXPLOSION ou une fuite de liquide ou de gaz inflammable. - UNE BATTERIE soumise à une pression d'air extrêmement basse pouvant entraî ner une EXPLOSION ou une fuite de liquide ou de gaz inflammable. VMS-RPPS Quick Reference Guide 13... -
Page 14: Table Of Contents
9-60V DC power-in connector (9-60V DC-in) ................ 29 2.1.3 General purpose I/O connector (GPIO) ................. 30 2.2 VMS-RPPS Product Overview ................31 2.3 VMS-RPPS Jumper and Connector List ..............32 2.4 VMS-RPPS Setting Jumpers & Connectors ............34 2.4.1 AT/ATX Input power select (JAT1) ..................34 2.4.2... - Page 15 Quick Reference Guide Installation ......................43 3.1 Installing Hard Disk & SIM card (VMS-RPPS) ............45 3.2 Installing Hard Disk & SIM card (VMS-RPPS) ............46 3.3 System Mounting ....................48 4. Drivers Installation....................... 49 4.1 Install Chipset Driver ....................50 4.2 Install VGA Driver ....................
- Page 16 5.6.6.2 Discard Changes and Reset ..................... 92 5.6.6.3 Restore Defaults ....................... 92 5.6.6.4 Launch EFI Shell from filesystem device ................. 92 5.6.7 MEBx ........................... 93 6. Maintenance & Troubleshooting................. 94 7. Product Application ..................... 99 16 VMS-RPPS Quick Reference Guide...
-
Page 17: Getting Started
Screwdriver for chassis Wire tie for HDMI Thermal pad for M.2 NVMe SSD Thermal pad for Memory Accessory kit (Rubber foot and Screws) Terminal block to lockable DC Jack cable (optional) 120W adapter (optional) Power cord (optional) VMS-RPPS Quick Reference Guide 17... - Page 18 Step 3: Carefully cut the tape sealing the box. Only cut deep enough to break the tape. Step 4: Open the inside box. Step 5: Take out the box pc from the boxes. Step 6: Remove the peripheral parts from the box. 18 VMS-RPPS Quick Reference Guide...
-
Page 19: System Specifications
LED Indicator 1 x LED indicators for LTE (Green) - M.2 B-key 1 x LED indicators for Wi-Fi (Green) - M.2 E-key COM Port 1 x RS232/422/485(BIOS), support auto-flow 1 x 10-bits GPIO Digital I/O VMS-RPPS Quick Reference Guide 19... - Page 20 4 x 10/100/1000/2.5G Base-Tx GbE compatible 2.5G LAN Port (I226IT) LED indicator (LAN for active, speed) ACT/LINK SPEED Definition Definition LED Indicator Light Off No Link Solid Orange 2.5G Solid Yellow Connection Solid Green 1G/100M Flashing Activity Light Off 20 VMS-RPPS Quick Reference Guide...
- Page 21 10.5V 12.0V 11.0V 12.5V 11.0V 12.5V 11.5V ◼ The following behaviors happen if ACC Function (JACC1) sets up as Enable: VMS-RPPS won’t power on if the DC Input voltage is lower than the startup voltage. VMS-RPPS Quick Reference Guide 21...
- Page 22 10sec / 30sec / 1min / 5min / 10 min / 15min / 30min / 1hr. The delay time starts to count if ignition turns on. User can skip the delay time to turn on VMS-RPPS if pressing power button. VMS-RPPS will automatically power on if the delay time ends up.
- Page 23 Reference ISTA 2A, Method : IEC-60068-2-32 Test : Ed Test phase : One corner, three edges, six faces IP Rating IP50 Mounting Kit Wall mount kit (Standard) Software Support OS Information Win10, Win11, Linux Note: Specifications are subject to change without notice. VMS-RPPS Quick Reference Guide 23...
-
Page 24: System Overview
VMS-RPPS 1.4 System Overview 1.4.1 Front View 1.4.2 Rear View 24 VMS-RPPS Quick Reference Guide... - Page 25 9-60V DC-in 9-60V DC power-in connector HDMI 2 x HDMI connector DP++ 2 x DP connector RJ-45 4 x RJ-45 Ethernet Mic-in audio jack Mic-in & Line-out Line-out audio jack Antenna 3 x Antenna w/cover VMS-RPPS Quick Reference Guide 25...
-
Page 26: System Dimensions
VMS-RPPS 1.5 System Dimensions (Unit: mm) 26 VMS-RPPS Quick Reference Guide... -
Page 27: Operating Principle
- The power ON/OFF LED will turn blue to indicate power is on. Note - Check with the Icon behavior for power status. *Note: Power LED. S0: On S3: Blinking S4/S5: Off BIOS P.O.S.T: Blinking. VMS-RPPS Quick Reference Guide 27... -
Page 28: Hardware Configuration
VMS-RPPS 2. Hardware Configuration For advanced information, please refer to: 1- VMS-RPPS main board included in this manual. Note: If you need more information, please visit our website: www.avalue.com 28 VMS-RPPS Quick Reference Guide... -
Page 29: Vms-Rpps Connector Mapping
Signal RS-485 TxD1- Signal PIN PIN Signal TxD1+ DATA1- RxD1+ DATA1+ RxD1- 2.1.2 9-60V DC power-in connector (9-60V DC-in) Signal VIN + (BAT+) Note: ACC (IGN) Please refer to JVIN1 for PSU connection. VIN- (BAT-) VMS-RPPS Quick Reference Guide 29... -
Page 30: General Purpose I/O Connector (Gpio)
VMS-RPPS 2.1.3 General purpose I/O connector (GPIO) Signal Signal Signal DIO_GPI0 DIO_GPO0 GPI_COM DIO_GPI1 DIO_GPO1 DIO_GPI2 DIO_GPO2 DIO_GPI3 DIO_GPO3 DIO_GPI4 10 DIO_GPO4 +V30_GPO 30 VMS-RPPS Quick Reference Guide... -
Page 31: Vms-Rpps Product Overview
Quick Reference Guide 2.2 VMS-RPPS Product Overview VMS-RPPS Quick Reference Guide 31... -
Page 32: Vms-Rpps Jumper And Connector List
VMS-RPPS 2.3 VMS-RPPS Jumper and Connector List You can configure your board to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. - Page 33 DCOUT1 DC Output connector 2 x 1 wafer, pitch 2.50 mm JEC1 EC connector 3 x 1 header, pitch 2.00 mm JLINEIN Audio connector 4 x 1 wafer, pitch 2.00 mm HDMI1/2 HDMI connector 1/2 VMS-RPPS Quick Reference Guide 33...
-
Page 34: Vms-Rpps Setting Jumpers & Connectors
VMS-RPPS 2.4 VMS-RPPS Setting Jumpers & Connectors 2.4.1 AT/ATX Input power select (JAT1) * Default 2.4.2 Clear CMOS (JRTC1) Normal* Clear CMOS * Default 34 VMS-RPPS Quick Reference Guide... -
Page 35: Power Input Selection (Jbat1)
Quick Reference Guide 2.4.3 Power Input Selection (JBAT1) +9V ~ +60V* +12V +24V +48V * Default 2.4.4 Vehicle/Industrial PC power mode selector (JACC1) Enable* Disable * Default VMS-RPPS Quick Reference Guide 35... -
Page 36: Key-B Power Mode Setting (Jpwr1)
VMS-RPPS 2.4.5 M.2 KEY-B power mode setting (JPWR1) +3.3V* 3.8V * Default 2.4.6 SPI connector (JSPI) Signal PIN PIN Signal BIOS_WP# SPI0_HOLD# SPI0_BIOS_MOSI SPI0_BIOS_MISO SPI0_BIOS_CLK SPI0_R_CS0# +3.3VSB +3.3VSB 36 VMS-RPPS Quick Reference Guide... -
Page 37: Dc Output Connector (Dcout1)
Quick Reference Guide 2.4.7 DC Output connector (DCOUT1) Signal +12VSB Note: Max. Current Value: 3A 2.4.8 Battery connector (BT1) Signal +RTCBATT VMS-RPPS Quick Reference Guide 37... -
Page 38: Audio Connector (Jlinein)
VMS-RPPS 2.4.9 Audio connector (JLINEIN) Signal LINEIN_R LINEIN_L LINE1-JD 2.4.10 DC-Input connector (JVIN1) Signal +VIN_BAT ACC_ON 38 VMS-RPPS Quick Reference Guide... -
Page 39: Pc Connector (Jpc1)
Quick Reference Guide 2.4.11 PC connector (JPC1) Signal VCCCORE_nPMALERT VCCCORE_PMSDA VCCCORE_PMSCL +3.3VSB 2.4.12 EC connector (JEC1) Signal EC_SMDAT_DEBUG EC_SMCLK_DEBUG VMS-RPPS Quick Reference Guide 39... -
Page 40: Espi Connector (Jespi1)
VMS-RPPS 2.4.13 ESPI connector (JESPI1) Signal PIN PIN Signal ESPI_ALER1# ESPI_RST# ESPI_CS1# ESPI_CLK_80P ESPI_IO3_80P ESPI_CS# ESPI_IO2_80P RST_SOCKET# ESPI_IO1_80P +3.3VSB ESPI_IO0_80P 2.4.14 USB connector (JUSB2) Signal PIN PIN Signal USB_DP_6 USB_DP_5 USB_DN_6 USB_DN_5 +5VSB +5VSB 40 VMS-RPPS Quick Reference Guide... -
Page 41: Serial Port 2 Connector (Jcom2)
Serial port 2 connector (JCOM2) Signal PIN PIN Signal COM_RXD_TXP_2 COM_DCD#_TXN_2 COM_DTR#_RXN_2 COM_TXD_RXP_2 COM_DSR#_2 COM_CTS#_2 COM_RTS#_2 COM_RI#_2 2.4.16 Serial port 3 connector (JCOM3) Signal PIN PIN Signal COM_RXD_TXP_3 COM_DCD#_TXN_3 COM_DTR#_RXN_3 COM_TXD_RXP_3 COM_DSR#_3 COM_CTS#_3 COM_RTS#_3 COM_RI#_3 VMS-RPPS Quick Reference Guide 41... -
Page 42: Gps Connector (Cn2)
VMS-RPPS 2.4.17 GPS connector (CN2) Signal GPS_TIMEPULSE 42 VMS-RPPS Quick Reference Guide... -
Page 43: Installation
Quick Reference Guide 3. Installation VMS-RPPS Quick Reference Guide 43... - Page 44 ⚫ Anti-static Discharge: If a user open the rear of the box PC, to configure the jumpers or plug in added peripheral devices, ground themselves first and wear an anti-static wristband. 44 VMS-RPPS Quick Reference Guide...
-
Page 45: Installing Hard Disk & Sim Card (Vms-Rpps)
Quick Reference Guide 3.1 Installing Hard Disk & SIM card (VMS-RPPS) Step 1. Unfasten 6 screws from the HDD brackets/SIM card slot and take it off. Step 2. Remove 8 screws to release the HDD brackets. Step 3. Slide HDD/SIM card into its brackets until properly seated. -
Page 46: Installing Hard Disk & Sim Card (Vms-Rpps)
VMS-RPPS 3.2 Installing Hard Disk & SIM card (VMS-RPPS) 46 VMS-RPPS Quick Reference Guide... - Page 47 Step4. Insert the M.2 B-Key and M.2 E-Key cards into their designated slots, then fasten them with screws to complete the installation. Step5. Insert the MPCIE card into its designated slot and fasten it with two screws to complete the installation. VMS-RPPS Quick Reference Guide 47...
-
Page 48: System Mounting
Keep the wires separated according to the interface. Wires that share similar electrical characteristics must be bundled together. ⚫ Do not bundle input wiring with output wiring. Keep them separate. ⚫ When necessary, it is strongly advised that you label wiring to all devices in the system. 48 VMS-RPPS Quick Reference Guide... -
Page 49: Drivers Installation
HID touch digitizer built-in driver in Windows 7 or later. (For reference only) Note: Installation procedures and screen shots in this section are for your reference and may not be exactly the same as shown on your screen. VMS-RPPS Quick Reference Guide 49... -
Page 50: Install Chipset Driver
Windows 11 operation system. If the warning message appears while the installation process, click Continue to go on. Step 3. Click Install. Step1. Click Next. Step 4. Click Finish to complete setup. Step 2. Click Accept. 50 VMS-RPPS Quick Reference Guide... -
Page 51: Install Vga Driver
Windows 11 operation system. Step 3. Click Accept. Step 1. Click Begin installation. Step 4. Click Start. Step 5. Click Finish to complete setup. Step 2. Click I agree. VMS-RPPS Quick Reference Guide 51... -
Page 52: Install Audio Driver
All drivers can be found on the Avalue Official Website: www.avalue.com. Note: The installation procedures and screen shots in this section are based on Windows 11 operation system. Step 1. Click Yes to continue installation. Step 2. Click Finish to complete setup. 52 VMS-RPPS Quick Reference Guide... -
Page 53: Install Ethernet Driver
All drivers can be found on the Avalue Official Website: www.avalue.com. Note: The installation procedures and screen shots in this section are based on Windows 11 operation system. Step 1. Click OK to continue installation. Step 2. Setup completed. VMS-RPPS Quick Reference Guide 53... -
Page 54: Install Me Driver
Note: The installation procedures and screen shots in this section are based on Windows 11 operation system. Step 3. Click Next. Step 1. Click Next to continue installation. Step 4. Click Finish to complete setup. Step 2. Click Next. 54 VMS-RPPS Quick Reference Guide... -
Page 55: Install Intel Sst Driver
Note: The installation procedures and screen shots in this section are based on Windows 11 operation system. Step 3. Setup completed. Step 1. Click Browse my computer for drivers to continue installation. Step 2. Click Next. VMS-RPPS Quick Reference Guide 55... -
Page 56: Install Serial Io Driver
Windows 11 operation system. Step 3. Click Next. Step 1. Click Next to continue installation. Step 4. Click Next. Step 2. Click Next. Step 5. Click Finish to complete setup. 56 VMS-RPPS Quick Reference Guide... -
Page 57: Bios Setup
Quick Reference Guide 5.BIOS Setup VMS-RPPS Quick Reference Guide 57... -
Page 58: Introduction
If you do not press the keys at the correct time and the system does not boot, an error message will be displayed and you will again be asked to. Press F1 to Continue, DEL to enter SETUP 58 VMS-RPPS Quick Reference Guide... -
Page 59: Using Setup
Note: Some of the navigation keys differ from one screen to another. • To Display a Sub Menu Use the arrow keys to move the cursor to the sub menu you want. Then press <Enter>. A “➢” pointer marks all sub menus. VMS-RPPS Quick Reference Guide 59... -
Page 60: Getting Help
BIOS Vendor and your systems manufacturer to provide the absolute maximum performance and reliability. Even a seemingly small change to the chipset setup has the potential for causing you to use the override. 60 VMS-RPPS Quick Reference Guide... -
Page 61: Bios Setup
<Enter> to accept and enter the sub-menu. 5.6.1 Main Menu This section allows you to record some basic hardware configurations in your computer and set the system clock. VMS-RPPS Quick Reference Guide 61... -
Page 62: System Language
Visit the Avalue website (www.avalue.com) to download the latest product and BIOS information. 5.6.2 Advanced Menu This section allows you to configure your CPU and other system devices for basic operation through the following sub-menus. 62 VMS-RPPS Quick Reference Guide... -
Page 63: Cpu Configuration
Use the CPU configuration menu to view detailed CPU specification and configure the CPU. Item Options Description When enabled, a VMM can utilize the additional Intel (VMX) Virtualization Disabled hardware capabilities provided by Vanderpool Technology Enabled[Default] Technology. 5.6.2.1.1 Efficient-core Information VMS-RPPS Quick Reference Guide 63... -
Page 64: Performance-Core Information
VMS-RPPS 5.6.2.1.2 Performance-core Information 5.6.2.2 Power & Performance 64 VMS-RPPS Quick Reference Guide... -
Page 65: Cpu - Power Management Control
Speed Step or Intel Speed Shift to be available and Disabled enabled). Enabled[Default], C States Enable/Disable CPU Power Management. Disabled Enabled, Enable/Disable C1E. When enabled, CPU will switch Enhanced C-States Disabled[Default] to minimum speed when all cores enter C-State. VMS-RPPS Quick Reference Guide 65... -
Page 66: Pch-Fw Configuration
Description Disabled When Disabled ME will be put into ME Temporarily ME State Enabled[Default], Disabled Mode. 5.6.2.3.1 Firmware Update Configuration Item Option Description Disabled[Default], ME FW Image Re-Flash Enable/Disable Me FW Image Re-Flash function. Enabled 66 VMS-RPPS Quick Reference Guide... -
Page 67: Ptt Configuration
5.6.2.4 Trusted Computing Item Options Description Enables or Disables BIOS support for security device. Disable, Security Device Support O.S. will not show Security Device. TCG EFI protocol Enable[Default] and INT1A interface will not be available. VMS-RPPS Quick Reference Guide 67... -
Page 68: Apci Settings
S3 (Suspend to RAM)[Default] button is pressed. 5.6.2.6 Super IO Configuration You can use this item to set up or change the Super IO configuration for serial ports. Please refer to 5.6.2.6.1 ~ 5.6.2.6.3 for more information. 68 VMS-RPPS Quick Reference Guide... -
Page 69: Serial Port 1 Configuration
Low: RS232/422/485 = 250Kbps UART Slew Rate High High: RS232 = 3Mbps, RS422/485 = 20Mbps. Non INT+EXT R[Default] EXT R Adjust the Serial Port with internal or external UART 422/485 Termination INT R termination resistors. INT+EXT R VMS-RPPS Quick Reference Guide 69... -
Page 70: Serial Port 2 Configuration
Low: RS232/422/485 = 250Kbps UART Slew Rate High High: RS232 = 3Mbps, RS422/485 = 20Mbps. Non INT+EXT R[Default] EXT R Adjust the Serial Port with internal or external UART 422/485 Termination INT R termination resistors. INT+EXT R 70 VMS-RPPS Quick Reference Guide... -
Page 71: Serial Port 3 Configuration
Low: RS232/422/485 = 250Kbps UART Slew Rate High High: RS232 = 3Mbps, RS422/485 = 20Mbps. Non INT+EXT R[Default] EXT R Adjust the Serial Port with internal or external UART 422/485 Termination INT R termination resistors. INT+EXT R VMS-RPPS Quick Reference Guide 71... -
Page 72: Ec 5782 Hw Monitor
10 Min 15 Min 30 Min 1 Hour w/o delay[Default] 20 Sec 1 Min 5 Min Power Off Delay 10 Min Power Off Delay while Ignition turn off. 30 Min 1 Hour 6 Hour 18 Hour 72 VMS-RPPS Quick Reference Guide... -
Page 73: S5 Rtc Wake Settings
Select Dynamic Time, System will wake on the current time Dynamic Time + Increase minute(s). 5.6.2.9 Serial Port Console Redirection Item Options Description Disabled[Default], Console Redirection Console Redirection Enable or Disable. Enabled Disabled[Default], Console Redirection EMS Console Redirection Enable or Disable. Enabled VMS-RPPS Quick Reference Guide 73... -
Page 74: Legacy Console Redirection Settings
Legacy OS and Legacy OPROM Messages. 5.6.2.10 USB Configuration The USB Configuration menu helps read USB information and configures USB settings. Item Options Description 1 sec The time-out value for Control, Bulk, and USB transfer time-out 5 sec Interrupt transfers. 74 VMS-RPPS Quick Reference Guide... -
Page 75: Network Stack Configuration
Optical drives are emulated as ‘CDROM’, drives with no media will be Hard Disk CD-ROM emulated according to a drive type. 5.6.2.11 Network Stack Configuration Item Options Description Enabled Network Stack Enable/Disable UEFI Network Stack. Disabled[Default] VMS-RPPS Quick Reference Guide 75... -
Page 76: Nvme Configuration
VMS-RPPS 5.6.2.12 NVMe Configuration 5.6.3 Chipset 76 VMS-RPPS Quick Reference Guide... -
Page 77: System Agent (Sa) Configuration
Quick Reference Guide 5.6.3.1 System Agent (SA) Configuration Item Option Description Enabled[Default] VT-d VT-d capability. Disabled 5.6.3.1.1 Memory Configuration VMS-RPPS Quick Reference Guide 77... -
Page 78: Graphics Configuration
VMS-RPPS 5.6.3.1.2 Graphics Configuration Item Option Description Auto Select IGFX Graphic device should be Primary Primary Display IGFX[Default] Display. 5.6.3.1.3 VMD setup menu Item Option Description Enabled Enable VMD controller Enable/Disable VMD controller. Disabled[Default] 78 VMS-RPPS Quick Reference Guide... -
Page 79: Pci Express Configuration
PCI Express Root Port 1 Control the PCI Express Root Port. Disabled Disabled[Default], Set the ASPM Level: Force L0s – Force all links to L0s State AUTO – BIOS auto ASPM configure DISABLE – Disables ASPM. L0sL1 Auto VMS-RPPS Quick Reference Guide 79... -
Page 80: Pch-Io Configuration
VMS-RPPS 5.6.3.2 PCH-IO Configuration 5.6.3.2.1 PCI Express Configuration 80 VMS-RPPS Quick Reference Guide... -
Page 81: Pci Express Root Port 3(M.2 Keyb)
DISABLE – Disables ASPM. Auto Disabled[Default] L1 Substates L1.1 PCI Express L1 Substates settings. L1.1 & L1.2 Disabled[Default], PCI Express L1 Low Substates L1 Low Enabled Enable/Disable. Auto[Default] Gen1 PCIe Speed Configure PCIe Speed. Gen2 Gen3 VMS-RPPS Quick Reference Guide 81... -
Page 82: Pci Express Root Port 5(M.2 Keye/Mpcie)
DISABLE – Disables ASPM. Auto Disabled[Default] L1 Substates L1.1 PCI Express L1 Substates settings. L1.1 & L1.2 Disabled[Default], PCI Express L1 Low Substates L1 Low Enabled Enable/Disable. Auto[Default] Gen1 PCIe Speed Configure PCIe Speed. Gen2 Gen3 82 VMS-RPPS Quick Reference Guide... -
Page 83: Pci Express Root Port 7(Lan1-I226)
L1 Substates L1.1 PCI Express L1 Substates settings. L1.1 & L1.2 Disabled[Default], PCI Express L1 Low Substates L1 Low Enabled Enable/Disable. Disabled[Default], Enable/Disable Precision Time Enabled Measurement. Auto[Default] Gen1 PCIe Speed Configure PCIe Speed. Gen2 Gen3 VMS-RPPS Quick Reference Guide 83... -
Page 84: Pci Express Root Port 8(Lan2-I226)
L1 Substates L1.1 PCI Express L1 Substates settings. L1.1 & L1.2 Disabled[Default], PCI Express L1 Low Substates L1 Low Enabled Enable/Disable. Disabled[Default], Enable/Disable Precision Time Enabled Measurement. Auto[Default] Gen1 PCIe Speed Configure PCIe Speed. Gen2 Gen3 84 VMS-RPPS Quick Reference Guide... -
Page 85: Pci Express Root Port 9(Lan3-I226)
L1 Substates L1.1 PCI Express L1 Substates settings. L1.1 & L1.2 Disabled[Default], PCI Express L1 Low Substates L1 Low Enabled Enable/Disable. Disabled[Default], Enable/Disable Precision Time Enabled Measurement. Auto[Default] Gen1 PCIe Speed Configure PCIe Speed. Gen2 Gen3 VMS-RPPS Quick Reference Guide 85... -
Page 86: Pci Express Root Port 10(Lan4-I226)
L1 Substates L1.1 PCI Express L1 Substates settings. L1.1 & L1.2 Disabled[Default], PCI Express L1 Low Substates L1 Low Enabled Enable/Disable. Disabled[Default], Enable/Disable Precision Time Enabled Measurement. Auto[Default] Gen1 PCIe Speed Configure PCIe Speed. Gen2 Gen3 86 VMS-RPPS Quick Reference Guide... -
Page 87: Sata Configuration
State Drive or Hard Disk Drive. Enabled[Default] Port 1 Enable or Disable SATA Port. Disabled Hard Disk Drive Identify the SATA port is connected to Solid SATA Device Type Solid State Drive[Default] State Drive or Hard Disk Drive. VMS-RPPS Quick Reference Guide 87... -
Page 88: Hd Audio Configuration
Enabled = HDA will be Enabled[Default] unconditionally enabled. 5.6.3.3 Board & Panel Configuration Item Option Description Disabled[Default] ErP Function ErP Function (Deep S5). Enabled PWR-On After PWR-Fail Off[Default] AC loss resume. 88 VMS-RPPS Quick Reference Guide... -
Page 89: Show Dmi Info
Enabled[Default] Disabled[Default] 30 sec 40 sec 50 sec Watch Dog Select WatchDog. 1 min 2 min 10 min 30 min Disabled Enable/Disabled USB Standby Power USB Standby Power Enabled[Default] during S3/S4/S5. 5.6.3.3.1 SHOW DMI INFO VMS-RPPS Quick Reference Guide 89... -
Page 90: Security
VMS-RPPS 5.6.4 Security ⚫ Administrator Password Set setup Administrator Password ⚫ User Password Set User Password 5.6.4.1 Secure Boot 90 VMS-RPPS Quick Reference Guide... -
Page 91: Boot
Enabled boot option. Has no effect for BBS boot optios. Disabled[Default] Quiet Boot Enables or disables Quiet Boot option Enabled Boot Option #1 Set the system boot order. VMS-RPPS Quick Reference Guide 91... -
Page 92: Save And Exit
This option restores all BIOS settings to the factory default. This option is useful if the controller exhibits unpredictable behavior due to an incorrect or inappropriate BIOS setting. 5.6.6.4 Launch EFI Shell from filesystem device Attempts to Launch EFI Shell application (Shellx64.efi) from one of the available filesystem devices. 92 VMS-RPPS Quick Reference Guide... -
Page 93: Mebx
Quick Reference Guide 5.6.7 MEBx ⚫ Intel® ME Password MEBx Login VMS-RPPS Quick Reference Guide 93... -
Page 94: Maintenance & Troubleshooting
System Maintenance Introduction If the components of the product fail they must be replaced. Please contact the system reseller or vendor to purchase the replacement parts. Please follow the safety precautions outlined in the sections that follow 94 VMS-RPPS Quick Reference Guide... -
Page 95: General Safety Precautions
This equipment is not suitable for use in locations where children are likely to be present. DO NOT: ⚫ Drop the device against a hard surface. ⚫ In a site where the ambient temperature exceeds the rated temperature. VMS-RPPS Quick Reference Guide 95... -
Page 96: Anti - Static Precautions
This reduces the possibility of ESD damage. ⚫ Only handle the edges of the electrical component. When handling the electrical component, hold the electrical component by its edges. Please ensure the following safety precautions are adhered to at all times. 96 VMS-RPPS Quick Reference Guide... -
Page 97: Maintenance And Cleaning
Never drop any objects or liquids through the openings of the device. ⚫ Be cautious of any possible allergic reactions to solvents or chemicals used when cleaning the device. ⚫ Avoid eating, drinking and smoking within vicinity of the device. VMS-RPPS Quick Reference Guide 97... -
Page 98: Cleaning Tools
Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are excellent tools for wiping hard to reach areas. ⚫ Foam swabs: Whenever possible, it is best to use lint free swabs such as foam swabs for cleaning. 98 VMS-RPPS Quick Reference Guide... -
Page 99: Product Application
Avalue technical support team, or Avalue customer service representatives for further information. Feel free to inquire about this supplementary resource to enhance your understanding of the Watchdog Timer and Digital I/O (DIO) Application for optimal utilization of your box PC. VMS-RPPS Quick Reference Guide 99...
Need help?
Do you have a question about the VMS-RPPS and is the answer not in the manual?
Questions and answers