Related Manuals for Avalue Technology EMS-BYT Series
Summary of Contents for Avalue Technology EMS-BYT Series
- Page 1 EMS-BYT/BYTC1 Series Fanless Intel® Celeron®/Atom™ SoC Rugged Embedded System Quick Reference Guide Ed –17 April 2019 Copyright Notice Copyright 2019 Avalue Technology Inc., ALL RIGHTS RESERVED. Part No. E20178209A4R...
- Page 2 EMS-BYT/BYTC1 Series FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS "A"...
-
Page 3: Table Of Contents
1.4.1 Front View ..........................11 1.4.2 Rear View ........................... 11 System Dimensions ..................... 16 1.5.1 EMS-BYT Series Front & Top View ................... 16 1.5.2 EMS-BYTC1 Front & Top View....................17 Hardware Configuration ................... 18 EMS-BYT/BYTC1 connector mapping ..............19 2.1.1 External Serial Port 1 connector (COM1) .................. - Page 4 EMS-BYT/BYTC1 Series 2.4.6 UIM Switch select (JUIM1) ......................31 Serial port 1/ 2 – RS485 mode select (SW1) ................32 2.4.7 2.4.8 LPC port connector (JLPC1) ...................... 32 2.4.9 LCD inverter connector (JBKL1) ....................33 2.4.10 SPI connector (SPI1) ......................33 2.4.11 Front Panel Connector 1 (CN1) .....................
- Page 5 Quick Reference Guide In Case of Problems .................... 54 BIOS setup ......................55 3.6.1 Main Menu ..........................55 3.6.1.1 System Language ..........................55 3.6.1.2 System Date ............................ 55 3.6.1.3 System Time ............................ 55 3.6.2 Advanced Menu ......................... 56 3.6.2.1 ACPI Settings ..........................56 3.6.2.2 IT8528 Super IO Configuration ......................
- Page 6 EMS-BYT/BYTC1 Series 3.6.6.2 Discard Changes and Reset ......................81 3.6.6.3 Restore Defaults ..........................82 3.6.6.4 Launch EFI Shell from filesystem device ..................82 4. Drivers Installation ....................... 83 Install Chipset Driver ................... 84 Install MBI Driver ....................85 Install TXE Driver ....................86 Install VGA Driver ....................
-
Page 7: Getting Started
Quick Reference Guide 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. -
Page 8: System Specifications
EMS-BYT/BYTC1 Series 1.3 System Specifications System EBM-BYTS (EMS-BYT) EBM-BYTS + AUX-M01 (EMS-BYT-6COM) EBM-BYTS + AUX-M02 (EMS-BYT-5LAN) EBM-BYTS + AUX-M07 (EMS-BYT-4COM Isolation) Board EBM-BYTS + AUX-M04 (EMS-BYT-PSE) EBM-BYTS + EBM-BYTS DB-A (EMS-BYT-HDMI) EBM-BYTS + EBM-CDVS DB-A (EMS-BYT-DVI) ... - Page 9 Quick Reference Guide EMS-BYT-4COM Isolation, EMS-BYT-PSE) 1 x VGA, 1 x HDMI (EMS-BYT-HDMI) 1 x VGA, 1 x DVI (EMS-BYT-DVI) Audio Port Mic-in, Line-in, Line-out GPIO 6-bit GPI and 6-bit GPO 3 x USB 2.0 (Rear 2; Front 1) (EMS-BYT) ...
- Page 10 EMS-BYT/BYTC1 Series Relative Humidity 0% ~ 90% Relative Humidity, Non-condensing With mSATA/SSD: 5Grms, IEC 60068-2-64, Random, 10 ~ 500Hz, Vibration Protection 1hr/axis Shock Protection With mSATA/SSD: 50G, IEC 60068-2-27, Half Sine, 11ms CE, FCC Class B (EMS-BYT, EMS-BYT-6COM, EMS-BYT-5LAN, ...
-
Page 11: System Overview
Quick Reference Guide 1.4 System Overview 1.4.1 Front View EMS-BYT Series EMS-BYTC1 1.4.2 Rear View EMS-BYT EMS-BYT/BYTC1 Series Quick Reference Guide 11... - Page 12 EMS-BYT/BYTC1 Series EMS-BYT-6COM/4COM Isolation EMS-BYT-5LAN/PSE EMS-BYT-HDMI 12 EMS-BYT/BYTC1 Series Quick Reference Guide...
- Page 13 Quick Reference Guide EMS-BYT-DVI EMS-BYT-USB EMS-BYT Connectors Label Function Note COM1 Serial port connector 1 DC power-in connector DC-IN LAN1 RJ-45 Ethernet 1 Multi-Function Port combined COM2, Multi-function port 2 PS/2, Audio, GPIO and SMBus 3 x USB2.0 connector VGA connector 2.5”...
- Page 14 EMS-BYT/BYTC1 Series EMS-BYT-6COM/4COM Isolation Connectors Label Function Note COM1 Serial port connector 1 COM3~6 Serial port connector3~6 DC-IN DC power-in connector LAN1 RJ-45 Ethernet 1 Multi-Function Port combined COM2, Multi-function port 2 PS/2, Audio, GPIO and SMBus 5 x USB2.0 connector VGA connector 2.5”...
- Page 15 Quick Reference Guide VGA connector 2.5” Driver Bay and SIM Card Swappable Drawer HDD indicator HDMI HDMI connector EMS-BYT-DVI Connectors Label Function Note COM1 Serial port connector1 DC-IN DC power-in connector LAN1 RJ-45 Ethernet 1 Multi-Function Port combined COM2, Multi-function port 2 PS/2, Audio, GPIO and SMBus 5 x USB2.0 connector VGA connector...
-
Page 16: System Dimensions
EMS-BYT/BYTC1 Series 1.5 System Dimensions 1.5.1 EMS-BYT Series Front & Top View (Unit: mm) 16 EMS-BYT/BYTC1 Series Quick Reference Guide... -
Page 17: Ems-Bytc1 Front & Top View
Quick Reference Guide 1.5.2 EMS-BYTC1 Front & Top View (Unit: mm) EMS-BYT/BYTC1 Series Quick Reference Guide 17... -
Page 18: Hardware Configuration
EMS-BYT/BYTC1 Series 2. Hardware Configuration Jumper and Connector Setting, Driver and BIOS Installing For advanced information, please refer to: 1- EBM-BYTS, AUX-M01, AUX-M02, AUX-M04, AUX-M07, EBM-BYTS DB-A, EBM-CDVS DB-A and EBM-BYTS DB-E included in this manual. Note: If you need more information, please visit our website: http://www.avalue.com.tw 18 EMS-BYT/BYTC1 Series Quick Reference Guide... -
Page 19: Ems-Byt/Bytc1 Connector Mapping
Quick Reference Guide 2.1 EMS-BYT/BYTC1 connector mapping 2.1.1 External Serial Port 1 connector (COM1) RS-232 RS-485 RS-422 TXD-/RXD- TXD- TXD+/RXD+ TXD+ RXD+ RXD- 2.1.2 External Serial Port 3/4/5/6 connector (COM3/4/5/6) RS-232 RS-485 RS-422 TXD-/RXD- TXD- TXD+/RXD+ TXD+ RXD+ RXD- EMS-BYT/BYTC1 Series Quick Reference Guide 19... -
Page 20: Vga Connector (Vga)
EMS-BYT/BYTC1 Series 2.1.3 VGA connector (VGA) Signal PIN Signal PIN Signal GREEN DDCDAT BLUE HSYNC VSYNS DDCCLK 2.1.4 Multi-Function Port combined COM2, 2 PS/2, Audio, GPIO and SMBus (Multi-function port) Signal Signal Signal LINE1_JD FRONT_JD LINE1_RIN MIC1_JD LINEOUT_R MIC_RIN LINE1_LIN LINEOUT_L MIC_LIN SMB_CLK... -
Page 21: Gpio+Smbus
Quick Reference Guide 2.1.4.1 GPIO+SMBUS Signal PIN PIN Signal SMBUS_DATA SMBUS_CLK GPI-D5 GPI-D4 GPO-D5 GPI-D3 GPO-D4 GPI-D2 GPO-D3 GPI-D1 GPO-D2 GPI-D0 GPO-D1 GPO-D0 2.1.4.2 COM2 Pin RS-232 RS-485 RS-422 TXD-/RXD- TXD- TXD+/RXD+ TXD+ RXD+ RXD- EMS-BYT/BYTC1 Series Quick Reference Guide 21... -
Page 22: Ebm-Byts, Aux-M01, Aux-M02, Aux-M04, Aux-M07, Ebm-Byts Db-A
EMS-BYT/BYTC1 Series 2.2 EBM-BYTS, AUX-M01, AUX-M02, AUX-M04, AUX-M07, EBM-BYTS DB-A, EBM-CDVS DB-A and EBM-BYTS DB-E Overviews 2.2.1 EBM-BYTS 22 EMS-BYT/BYTC1 Series Quick Reference Guide... -
Page 23: Aux-M01
Quick Reference Guide 2.2.2 AUX-M01 2.2.3 AUX-M02 EMS-BYT/BYTC1 Series Quick Reference Guide 23... -
Page 24: Aux-M04
EMS-BYT/BYTC1 Series 2.2.4 AUX-M04 2.2.5 AUX-M07 24 EMS-BYT/BYTC1 Series Quick Reference Guide... -
Page 25: Ebm-Byts Db-A
Quick Reference Guide 2.2.6 EBM-BYTS DB-A 2.2.7 EBM-CDVS DB-A EMS-BYT/BYTC1 Series Quick Reference Guide 25... -
Page 26: Ebm-Byts Db-E
EMS-BYT/BYTC1 Series 2.2.8 EBM-BYTS DB-E 26 EMS-BYT/BYTC1 Series Quick Reference Guide... -
Page 27: Ebm-Byts Jumper & Connector List
Quick Reference Guide 2.3 EBM-BYTS Jumper & Connector list Jumpers Label Function Note JCMOS1 Clear CMOS 3 x 1 header, pitch 2.54mm JCMOS2 Clear CMOS (Reserved) 3 x 1 header, pitch 2.54 mm JRI1/2 COM 1/2 pin 9 signal select 3 x 2 header, pitch 2.00 mm 3 x 1 header, pitch 2.00 mm JAT1... - Page 28 EMS-BYT/BYTC1 Series SO_DIMM1 DDR3 SODIMM connector MIOE_CB1 IET Expansion slot JLPC1 LPC port connector 7 x 2 header, pitch 2.00 mm SPI1 SPI connector 4 x 2 header, pitch 2.00 mm JBKL1 LCD inverter connector 5 x 1 wafer, pitch 2.00 mm Serial ATA connector 1 SATA1 Front Panel connector 1...
-
Page 29: Ebm-Byts Jumpers & Connectors Settings
Quick Reference Guide 2.4 EBM-BYTS Jumpers & Connectors settings 2.4.1 Clear CMOS (JCMOS1) Protect* Clear CMOS *Default 2.4.2 COM 1/2 pin 9 signal select (JRI1/2) Ring* +12V JRI2 JRI1 * Default EMS-BYT/BYTC1 Series Quick Reference Guide 29... -
Page 30: At/ Atx Input Power Select (Jat1)
EMS-BYT/BYTC1 Series 2.4.3 AT/ ATX Input power select (JAT1) *Default 2.4.4 LCD backlight brightness adjustment (JVR1) PWM Mode* DC Mode * Default 30 EMS-BYT/BYTC1 Series Quick Reference Guide... -
Page 31: Iet Interface Dp Mode Select (Jddi1)
Quick Reference Guide 2.4.5 IET interface DP mode select (JDDI1) HDMI/DVI Display Port* *Default 2.4.6 UIM Switch select (JUIM1) UIM on MPCIE1 UIM on MPCIE2* * Default EMS-BYT/BYTC1 Series Quick Reference Guide 31... -
Page 32: Serial Port 1/ 2 - Rs485 Mode Select (Sw1)
EMS-BYT/BYTC1 Series Serial port 1/ 2 – RS485 mode select (SW1) 2.4.7 In Serial Port 1 mode Auto Direction RTS# Control* 485TXP external OPEN* biasing resistor 485TXN external OPEN* biasing resistor In Serial Port 2 mode Auto Direction RTS# Control* 485TXP external OPEN* biasing resistor... -
Page 33: Lcd Inverter Connector (Jbkl1)
Quick Reference Guide 2.4.9 LCD inverter connector (JBKL1) Signal +12V BKLEN VBRIGHT 2.4.10 SPI connector (SPI1) Signal PIN PIN Signal SPI_HOLD# SPI_ROM_MOSI SPI_ROM_MISO_R SPI_ROM_CLK SPI_ROM_CS# +VSPI_BIOS EMS-BYT/BYTC1 Series Quick Reference Guide 33... -
Page 34: Front Panel Connector 1 (Cn1)
EMS-BYT/BYTC1 Series 2.4.11 Front Panel Connector 1 (CN1) Signal PWR_BTN_IN# SYSRST# +5VSB PWR_LED- 2.4.12 Front Panel Connector 2 (CN2) Signal +3.3V SATA_5V_LED# +3.3VSB LAN1_LED_ACT_n +3.3VSB LAN1_LED_100#_n +3.3VSB LAN1_LED_1000#_n 34 EMS-BYT/BYTC1 Series Quick Reference Guide... -
Page 35: Dc Output Connector (Dcout_S1)
Quick Reference Guide 2.4.13 DC Output connector (DCOUT_S1) Signal DC_OUT DC_OUT DC_OUT 2.4.14 EC Debug connector (JEC_ROM1) Signal Signal EC_SMDAT_DE EC_SMCLK_D EBUG EC_HOLD# EC_FMOSI EC_FMISO EC_FSCK EC_FSCE# +VSPI_EC EMS-BYT/BYTC1 Series Quick Reference Guide 35... -
Page 36: On-Board Header For Usb2.0 (Jusb1)
EMS-BYT/BYTC1 Series 2.4.15 On-board header for USB2.0 (JUSB1) Signal USBVCC_HEADER USB_HUB2_DN_1 USB_HUB2_DP_1 2.4.16 LVDS connector (JLVDS1) Signal PIN PIN Signal +3.3V +3.3V LVDS_DATA0_P LVDS_DATA1_P LVDS_DATA0_N LVDS_DATA1_N LVDS_DATA2_P LVDS_DATA3_P LVDS_DATA2_N LVDS_DATA3_N LVDS_DATA4_P LVDS_DATA5_P LVDS_DATA4_N LVDS_DATA5_N LVDS_DATA6_P LVDS_DATA7_P LVDS_DATA6_N LVDS_DATA7_N LVDS_CLK1_P LVDS_CLK2_P LVDS_CLK1_N LVDS_CLK2_N +12V... -
Page 37: Aux-M01, Aux-M02, Aux-M04, Aux-M07, Ebm-Byts Db-A And Ebm-Cdvs Db-A Jumper & Connector List
Quick Reference Guide 2.5 AUX-M01, AUX-M02, AUX-M04, AUX-M07, EBM-BYTS DB-A and EBM-CDVS DB-A Jumper & Connector list 2.5.1 AUX-M01 Jumpers Label Function Note JRI3/4/5/6 COM 3/4/5/6 pin 9 signal select 3 x 2 header, pitch 2.00mm Connectors Label Function Note USB1~2 USB connector 1~2 USB connector 3... - Page 38 EMS-BYT/BYTC1 Series 2.5.4 AUX-M07 Connectors Label Function Note USB1~2 USB connector 1~2 Serial port connector 3~6 COM3~6 SMBUS of TCA9555 address setting 3 x 2 header, pitch 2.00mm SJP2 2.5.5 EBM-BYTS DB-A Jumpers Label Function Note OJRI3/4 COM 3/4 pin 9 signal select 3 x 2 header, pitch 2.00mm Connectors Label...
- Page 39 Quick Reference Guide USB4~7 4 x USB3.0 connector IET1 IET Expansion slot EMS-BYT/BYTC1 Series Quick Reference Guide 39...
-
Page 40: Aux-M01 Jumpers & Connectors Settings
EMS-BYT/BYTC1 Series 2.6 AUX-M01 Jumpers & Connectors settings 2.6.1 COM 3/4/5/6 pin 9 signal select (JRI3/4/5/6) Ring* JRI6 JRI5 +12V JRI4 JRI3 * Default 2.6.2 USB connector (USB3) Signal PUSBP3 PUSBN3 PV5A_USB3 40 EMS-BYT/BYTC1 Series Quick Reference Guide... -
Page 41: Usb Connector (Jusb3)
Quick Reference Guide 2.6.3 USB connector (JUSB3) Signal PUSBP3 PUSBN3 PV5A_USB3 2.6.4 SMBUS of TCA9555 address setting (PJP1) Signal PIN PIN Signal MC_9555A0 MC_9555A1 MC_9555A2 EMS-BYT/BYTC1 Series Quick Reference Guide 41... -
Page 42: Aux-M02 Connectors Settings
EMS-BYT/BYTC1 Series 2.7 AUX-M02 Connectors settings 2.7.1 LAN ACT/LNK/SPD LED (JLANLED) Signal PIN PIN Signal Z_LAN_LED_1000#_3 15 16 Z_LAN_LED_1000#_1 Z_LAN_LED_100#_3 Z_LAN_LED_100#_1 Z_LAN_LED_ACT_3 Z_LAN_LED_ACT_1 +3.3VSB +3.3VSB Z_LAN_LED_1000#_4 Z_LAN_LED_1000#_2 Z_LAN_LED_100#_4 Z_LAN_LED_100#_2 Z_LAN_LED_ACT_4 Z_LAN_LED_ACT_2 +3.3VSB +3.3VSB 42 EMS-BYT/BYTC1 Series Quick Reference Guide... -
Page 43: Normal/Bypass Mode Led (Jlanmode)
Quick Reference Guide 2.7.2 Normal/Bypass mode LED (JLANMODE) Signal PIN PIN Signal Z_RC5_LAN23-STA Z_RC7_LAN45-STA Z_+VLED Z_+VLED Z_RA4_LAN23-BYP Z_RA1_LAN45-BYP Z_+VLED Z_+VLED Z_RC6_LAN23-NOR Z_RC4_LAN45-NOR Z_+VLED Z_+VLED 2.8 AUX-M04 Jumpers & Connectors settings 2.8.1 Operating Modes select (ZJP1) Normal Auto* Reset * Default EMS-BYT/BYTC1 Series Quick Reference Guide 43... -
Page 44: Power Connector (Zpwr1)
EMS-BYT/BYTC1 Series 2.8.2 Power connector (ZPWR1) Signal +V12-28V +V12-28V +V12-28V 2.8.3 LAN ACT/LNK/SPD LED (Z_JLANLED) Signal PIN PIN Signal Z_LAN_LED_1000#_3 15 16 Z_LAN_LED_1000#_1 Z_LAN_LED_100#_3 Z_LAN_LED_100#_1 Z_LAN_LED_ACT_3 Z_LAN_LED_ACT_1 +3.3VSB +3.3VSB Z_LAN_LED_1000#_4 Z_LAN_LED_1000#_2 Z_LAN_LED_100#_4 Z_LAN_LED_100#_2 Z_LAN_LED_ACT_4 Z_LAN_LED_ACT_2 +3.3VSB +3.3VSB 44 EMS-BYT/BYTC1 Series Quick Reference Guide... -
Page 45: Aux-M07 Connector Settings
Quick Reference Guide 2.9 AUX-M07 Connector settings 2.9.1 SMBUS of TCA9555 address setting (SJP2) Signal PIN PIN Signal SMC_9555A0 SMC_9555A1 SMC_9555A2 EMS-BYT/BYTC1 Series Quick Reference Guide 45... -
Page 46: Ebm-Byts Db-A Jumpers & Connectors Settings
EMS-BYT/BYTC1 Series 2.10 EBM-BYTS DB-A Jumpers & Connectors settings 2.10.1 COM 3/4 pin 9 signal select (OJRI3/4) Ring* OJRI4 +12V OJRI3 * Default Serial port 1/ 2 – RS485 mode select (OJP485) 2.10.2 In Serial Port 1 mode Auto Direction RTS# Control* 485TXP external OPEN*... -
Page 47: Smbus Of Tca9555 Address Setting (Ojp1)
Quick Reference Guide 2.10.3 SMBUS of TCA9555 address setting (OJP1) Signal PIN PIN Signal MC_9555A0 MC_9555A1 MC_9555A2 EMS-BYT/BYTC1 Series Quick Reference Guide 47... -
Page 48: Ebm-Cdvs Db-A Connector Settings
EMS-BYT/BYTC1 Series 2.11 EBM-CDVS DB-A Connector settings 2.11.1 Front Panel Connector 1 (CN1) Signal SYSRST# SATA_LED# PWRSB_LED- 48 EMS-BYT/BYTC1 Series Quick Reference Guide... -
Page 49: Installing Hard Disk & Memory, Pci Devices (Ems-Byt/Bytc1 Series)
Quick Reference Guide 2.12 Installing Hard Disk & Memory, PCI devices (EMS-BYT/BYTC1 Series) Step 1. Remove 6 screws from the bottom of your system. Step 2. Remove the chassis cover. Step 1. Remove 5 screws to release the HDD bracket. Step 2.1 Slide HDD into its bracket until properly seated. -
Page 50: Installing Mounting Brackets (Ems-Byt/Bytc1 Series)
EMS-BYT/BYTC1 Series 2.13 Installing Mounting Brackets (EMS-BYT/BYTC1 Series) Step 1. Position brackets on both sides, matching the holes on the system. Step 2. Insert and fasten screw on each side of the system to secure Mounting brackets. 50 EMS-BYT/BYTC1 Series Quick Reference Guide... -
Page 51: Bios Setup
Quick Reference Guide 3.BIOS Setup EMS-BYT/BYTC1 Series Quick Reference Guide 51... -
Page 52: Introduction
EMS-BYT/BYTC1 Series 3.1 Introduction The BIOS setup program allows users to modify the basic system configuration. In this following chapter will describe how to access the BIOS setup program and the configuration options that may be changed. 3.2 Starting Setup The AMI BIOS™... -
Page 53: Using Setup
Quick Reference Guide 3.3 Using Setup In general, you use the arrow keys to highlight items, press <Enter> to select, use the PageUp and PageDown keys to change entries, press <F1> for help and press <Esc> to quit. The following table provides more detail about how to navigate in the Setup program using the keyboard. -
Page 54: Getting Help
EMS-BYT/BYTC1 Series 3.4 Getting Help Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press <Esc> or the F1 key again. 3.5 In Case of Problems If, after making and saving system changes with Setup, you discover that your computer no longer is able to boot, the AMI BIOS supports an override to the NVRAM settings which... -
Page 55: Bios Setup
Quick Reference Guide 3.6 BIOS setup Once you enter the Aptio Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and exit choices. Use the arrow keys to select among the items and press <Enter> to accept and enter the sub-menu. 3.6.1 Main Menu This section allows you to record some basic hardware configurations in your computer and set the system clock. -
Page 56: Advanced Menu
EMS-BYT/BYTC1 Series 3.6.2 Advanced Menu This section allows you to configure your CPU and other system devices for basic operation through the following sub-menus. 3.6.2.1 ACPI Settings Item Options Description Enable ACPI Auto Disabled[Default], Enables or Disables BIOS ACPI Auto Configuration Enabled Configuration. -
Page 57: It8528 Super Io Configuration
Quick Reference Guide Select the highest ACPI sleep state the Suspend Disabled, ACPI Sleep State system will enter when the SUSPEND S3 (Suspend to RAM) [Default] button is pressed. Disabled[Default], ErP Function ErP Function (Deep S5). Enabled Off[Default] PWR-On After PWR-Fail AC loss resume. -
Page 58: Serial Port 1 Configuration
EMS-BYT/BYTC1 Series Serial Port 5 Configuration Set Parameters of Serial Port 5 (COME). Serial Port 6 Configuration Set Parameters of Serial Port 6 (COMF). 3.6.2.2.1 Serial Port 1 Configuration Item Option Description Enabled[Default], Enable or Disable Serial Port Serial Port Disabled (COM). -
Page 59: Serial Port 2 Configuration
Quick Reference Guide 3.6.2.2.2 Serial Port 2 Configuration Item Option Description Enabled[Default], Enable or Disable Serial Port Serial Port Disabled (COM). Auto[Default] IO=2F8h; IRQ=3; IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12; Select an optimal setting for Change Settings IO=2F8h; IRQ=3,4,5,6,7,9,10,11,12; super IO device. IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12; IO=2E8h;... -
Page 60: Serial Port 3 Configuration
EMS-BYT/BYTC1 Series 3.6.2.2.3 Serial Port 3 Configuration Item Option Description Enabled[Default], Enable or Disable Serial Port Serial Port Disabled (COM). Auto[Default] IO=3E8h; IRQ=5; IO=3F8h; IRQ=3,4,5,6,7,10,11,12; Select an optimal setting for Change Settings IO=2F8h; IRQ=3,4,5,6,7,10,11,12; super IO device. IO=3E8h; IRQ=3,4,5,6,7,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,10,11,12; UART 232 (LOOPBACK) UART 232[Default] Change the Serial Port as... -
Page 61: Serial Port 4 Configuration
Quick Reference Guide 3.6.2.2.4 Serial Port 4 Configuration Item Option Description Enabled[Default], Enable or Disable Serial Port Serial Port Disabled (COM). Auto[Default] IO=2E8h; IRQ=10; IO=3F8h; IRQ=3,4,5,6,7,10,11,12; Select an optimal setting for Change Settings IO=2F8h; IRQ=3,4,5,6,7,10,11,12; super IO device. IO=3E8h; IRQ=3,4,5,6,7,10,11,12; IO=2E8h;... -
Page 62: Serial Port 5 Configuration
EMS-BYT/BYTC1 Series 3.6.2.2.5 Serial Port 5 Configuration Item Option Description Enabled[Default], Enable or Disable Serial Port Serial Port Disabled (COM). Auto[Default] IO=200h; IRQ=5; IO=200h; IRQ=3,4,5,6,7,10,11,12; Select an optimal setting for Change Settings IO=208h; IRQ=3,4,5,6,7,10,11,12; super IO device. IO=210h; IRQ=3,4,5,6,7,10,11,12; IO=218h; IRQ=3,4,5,6,7,10,11,12; UART 232 (LOOPBACK) UART 232[Default] Change the Serial Port as... -
Page 63: Serial Port 6 Configuration
Quick Reference Guide 3.6.2.2.6 Serial Port 6 Configuration Item Option Description Enabled[Default], Enable or Disable Serial Port Serial Port Disabled (COM). Auto[Default] IO=208h; IRQ=10; IO=200h; IRQ=3,4,5,6,7,10,11,12; Select an optimal setting for Change Settings IO=208h; IRQ=3,4,5,6,7,10,11,12; super IO device. IO=210h; IRQ=3,4,5,6,7,10,11,12; IO=218h;... -
Page 64: Ec 8528 H/W Monitor
EMS-BYT/BYTC1 Series 3.6.2.3 EC 8528 H/W Monitor 3.6.2.4 S5 RTC Wake Settings Item Options Description Enable or disable System wake on alarm Disabled[Default], event. Select Fixed Time, system will wake on Wake system from S5 Fixed Time the hr::min::sec specified. Select Dynamic Dynamic Time Time, System will wake on the current time + Increase minute(s). -
Page 65: Serial Port Console Redirection
Quick Reference Guide 3.6.2.5 Serial Port Console Redirection Item Options Description Disabled[Default], Console Redirection Console Redirection Enable or Disable. Enabled 3.6.2.6 CPU Configuration Use the CPU configuration menu to view detailed CPU specification and configure the CPU. Item Options Description All[Default], Number of cores to enable in each processor Active Processor Cores... -
Page 66: Socket 0 Cpu Information
EMS-BYT/BYTC1 Series Disabled[Default], Limit CPUID Maximum Disabled for Windows XP. Enabled XD can prevent certain classes of malicious buffer overflow attacks when combined with a Disabled, Execute Disable Bit supporting OS (Windows Server 2003 SP1, Enabled[Default] Windows XP SP2, SuSE Linux 9.2, RedHat Enterprise 3 Update 3.) When enabled, a VMM can utilize the Disabled,... -
Page 67: Ppm Configuration
Quick Reference Guide 3.6.2.7 PPM Configuration Item Options Description Disabled, CPU C state Report Enable/Disable CPU C state report to OS. Enabled[Default] C7[Default] This option controls Max C state that the Max CPU C-state processor will support. 3.6.2.8 IDE Configuration EMS-BYT/BYTC1 Series Quick Reference Guide 67... -
Page 68: Network Stack Configuration
EMS-BYT/BYTC1 Series Item Options Description Enabled[Default] Serial-ATA (SATA) Enable/Disable Serial ATA. Disabled, Gen1 SATA Speed Support SATA Speed Support Gen1 or Gen2. Gen2[Default] Port0 ODD SATA ODD Port Port1 ODD SATA ODD is Port0 or Port1. No ODD[Default] IDE Mode SATA Mode Select IDE/ AHCI. -
Page 69: Csm Configuration
Quick Reference Guide UEFI and Legacy This option controls Legacy/UEFI ROMs Boot option filter Legacy only[Default] priority. UEFI only Do not launch[Default] Controls the execution of UEFI and Legacy Network UEFI only PXE OpROM. Legacy only Do not launch Controls the execution of UEFI and Legacy Storage UEFI only Storage OpROM. -
Page 70: Usb Configuration
EMS-BYT/BYTC1 Series UEFI and Legacy This option controls Legacy/UEFI ROMs Boot option filter Legacy only[Default] priority. UEFI only Do not launch[Default] Controls the execution of UEFI and Legacy Network UEFI only PXE OpROM. Legacy only Do not launch Controls the execution of UEFI and Legacy Storage UEFI only Storage OpROM. -
Page 71: Security Configuration
Quick Reference Guide 1 sec 5 sec The time-out value for Control, Bulk, and USB transfer time-out 10 sec Interrupt transfers. 20 sec[Default] 10 sec 20 sec[Default] USB mass storage device Start Unit command Device reset time-out 30 sec time-out. 40 sec Maximum time the device will take before it properly reports itself to the Host Controller. -
Page 72: Chipset
EMS-BYT/BYTC1 Series 3.6.3 Chipset 3.6.3.1 North Bridge 72 EMS-BYT/BYTC1 Series Quick Reference Guide... -
Page 73: Intel Igd Configuration
Quick Reference Guide 3.6.3.1.1 Intel IGD Configuration Item Option Description Enabled[Default], Enable GOP Driver will unload GOP Driver Disabled VBIOS; Disable it will load VBIOS. Enable: Enable Integrated Graphics Integrated Graphics Enabled[Default], Device (IGD) when selected as the Device Disabled Primary Video Adaptor. -
Page 74: Igd - Lcd Control
EMS-BYT/BYTC1 Series 3.6.3.1.2 IGD - LCD Control Item Option Description 200[Default] LVDS Back Light PWM Select LVDS back light PWM Frequency. Frequency Enabled[Default] Active Internal LVDS (eDP->Ch7511- Active LVDS (Ch7511) to –LVDS). Disabled 1024x768 24/1[Default] 800x600 18/1 1024x768 18/1 1366x768 18/1 1024x600 18/1 1280x800 18/1 1920x1200 24/2... -
Page 75: South Bridge
Quick Reference Guide 1680x1050 24/2 LVDS Back Light PWM Select LVDS back light PWM duty. 100%[Default] 3.6.3.2 South Bridge Item Option Description Disabled Enable or Disable the High Precision High Precision Timer Enabled[Default] Event Timer. EMS-BYT/BYTC1 Series Quick Reference Guide 75... -
Page 76: Azalia Hd Audio
EMS-BYT/BYTC1 Series 3.6.3.2.1 Azalia HD Audio Item Option Description Control Detection of the Azalia device. Disabled = Azalia will be unconditionally Enabled[Default], Audio Controller disabled. Enabled = Azalia will be Disabled unconditionally Enabled. Auto = Azalia will be enabled if present disabled otherwise. Enabled[Default], HDMI Port B Enable/Disable HDMI Port B. -
Page 77: Pci Express Configuration
Quick Reference Guide Item Option Description Please select the corresponding type of Windows for OS installation. Please change the item of OS selection to Windows 8.X[Default] Windows 7 if you intend to install Windows 7 OS Selection Android Windows 7 Please change the item of OS selection to Windows 8.X if you intend to install Windows 8 OS. -
Page 78: Security
EMS-BYT/BYTC1 Series 3.6.4 Security Administrator Password Set setup Administrator Password User Password Set User Password 3.6.4.1 Secure Boot menu 78 EMS-BYT/BYTC1 Series Quick Reference Guide... -
Page 79: Key Management
Quick Reference Guide Item Option Description Secure Boot can be enabled if 1.System Disabled[Default] Secure Boot running in User mode with enrolled Platform Enabled Key(PK) 2.CSM function is disabled. Secure Boot mode selector. ‘Custom’ Mode Standard Secure Boot Mode enables users to change Image Execution Custom[Default] policy and manage Secure Boot Keys. -
Page 80: Boot
EMS-BYT/BYTC1 Series 3.6.5 Boot Item Option Description Number of seconds to wait for setup activation Setup Prompt Timeout 1~ 65535 key. 65535(0xFFFF) means indefinite waiting. On[Default] Bootup NumLock State Select the Keyboard NumLock state Disabled[Default] Quiet Boot Enables or disables Quiet Boot option Enabled Enables or disables boot with initialization of a Disabled[Default]... -
Page 81: Save And Exit
Quick Reference Guide 3.6.6 Save and exit 3.6.6.1 Save Changes and Reset Reset the system after saving the changes. 3.6.6.2 Discard Changes and Reset Any changes made to BIOS settings during this session of the BIOS setup program are EMS-BYT/BYTC1 Series Quick Reference Guide 81... -
Page 82: Restore Defaults
EMS-BYT/BYTC1 Series discarded. The setup program then exits and reboots the controller. 3.6.6.3 Restore Defaults This option restores all BIOS settings to the factory default. This option is useful if the controller exhibits unpredictable behavior due to an incorrect or inappropriate BIOS setting. 3.6.6.4 Launch EFI Shell from filesystem device Attempts to Launch EFI Shell application (Shellx64.efi) from one of the available filesystem devices. -
Page 83: Drivers Installation
Quick Reference Guide 4. Drivers Installation Note: Installation procedures and screen shots in this section are for your reference and may not be exactly the same as shown on your screen. EMS-BYT/BYTC1 Series Quick Reference Guide 83... -
Page 84: Install Chipset Driver
EMS-BYT/BYTC1 Series 4.1 Install Chipset Driver Insert the Supporting DVD-ROM to DVD-ROM drive, and it should show the index page of Avalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to \Driver_Chipset\Intel\EMS-BYT. Note: The installation procedures and screen shots in this section are based on Windows 8.1 operation... -
Page 85: Install Mbi Driver
Quick Reference Guide 4.2 Install MBI Driver Insert the Supporting DVD-ROM to DVD-ROM drive, and it should show the index page of Avalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to \Utility\EMS-BYT_MBI. Note: The installation procedures and screen shots in this section are based on Windows 8.1 operation... -
Page 86: Install Txe Driver
EMS-BYT/BYTC1 Series 4.3 Install TXE Driver Insert the Supporting DVD-ROM to DVD-ROM drive, and it should show the index page of Avalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to \Utility\EMS-BYT_TXE. Note: The installation procedures and screen shots in this section are based on Windows 8.1 operation... -
Page 87: Install Vga Driver
Quick Reference Guide 4.4 Install VGA Driver Insert the Supporting DVD-ROM to DVD-ROM drive, and it should show the index page of Avalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to \VGA\EMS-BYT. Note: The installation procedures and screen shots in this section are based on Windows 8.1 operation... -
Page 88: Install Audio Driver (For Realtek Alc892)
EMS-BYT/BYTC1 Series 4.5 Install Audio Driver (For Realtek ALC892) Insert the Supporting CD-ROM to CD-ROM drive, and it should show the index page of Avalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to \Driver_Audio\Realtek\ALC892\EMS-BYT_Audio. -
Page 89: Install Ethernet Driver
Quick Reference Guide 4.6 Install Ethernet Driver Insert the Supporting DVD-ROM to DVD-ROM drive, and it should show the index page of Avalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to \Driver_Gigabit\Intel\I210\EMS-BYT_LAN.