Table of Contents
Advertisement
Quick Links
LPG detector (propane-butane)
Soporific gases detector (e.g. chloroform vapors).
SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
tel. +48 58 320 94 00
www.satel.pl
Carbon monoxide detector
DG-1 CO
Firmware version 3.00
DG-1 LPG
Firmware version 3.00
Natural gas detector (methane)
DG-1 ME
Firmware version 3.00
DG-1 TCM
Firmware version 3.00
EN
dg-1_pl 04/25
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Satel DG-1 CO
Summary of Contents for Satel DG-1 CO
- Page 1 Natural gas detector (methane) DG-1 ME Firmware version 3.00 Soporific gases detector (e.g. chloroform vapors). DG-1 TCM Firmware version 3.00 dg-1_pl 04/25 SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND tel. +48 58 320 94 00 www.satel.pl...
- Page 2 13 August 2005). The device meets the technical regulations of the Eurasian Customs Union. SATEL aims to continually improve the quality of its products, which may result in changes in their technical specifications and software. Current information about the changes being introduced is available on our website.
-
Page 3: Table Of Contents
CONTENTS Features ........................... 2 Description ........................2 Gas detection ........................2 Alarm signaling ......................... 2 Prelarm signaling ......................3 Trouble ..........................3 Trouble signaling ......................3 LED indicator ........................3 Sounder ..........................3 Electronics board ......................4 Tips for installation ......................4 Installation ........................ -
Page 4: Features
DG-1 CO / DG-1 LPG / DG-1 ME / DG-1 TCM SATEL This manual covers the following detectors: – carbon monoxide detector, DG-1 CO DG-1 LPG – LPG detector (propane-butane), – natural gas detector (methane), DG-1 ME DG-1 TCM – soporific gases detector (e.g. chloroform vapors). -
Page 5: Prelarm Signaling
SATEL DG-1 CO / DG-1 LPG / DG-1 ME / DG-1 TCM The sensor reaction is delayed, hence the end of signaling can take place even a few minutes after gas concentration dropped below the hazardous level. Prelarm signaling The DG-1 LPG and DG-1 ME detectors indicate prealarm by: •... -
Page 6: Electronics Board
• The DG-1 ME detector should be installed at a high level, just under the ceiling. • The DG-1 CO detector should be installed at a height of about 1.5 meters. • Do not install the detector in places where lacquers, glues, paint removers or aerosols are... -
Page 7: Installation
SATEL DG-1 CO / DG-1 LPG / DG-1 ME / DG-1 TCM • It is not recommended to install the detector in spaces where industrial type equipment is working. 5. Installation Disconnect power before making any electrical connections. 1. Turn the enclosure cover clockwise and remove it (Fig. 2). -
Page 8: Specifications
DG-1 CO / DG-1 LPG / DG-1 ME / DG-1 TCM SATEL It is not allowed to test the detector by any improvised methods (e.g. by using lighter gas). During the detector operation the gas sensor heats up. In the first five minutes after power-up, the DG-1 TCM detector is stabilizing. It may indicate alarm during that time.
Need help?
Do you have a question about the DG-1 CO and is the answer not in the manual?
Questions and answers