Advertisement
Quick Links
Thank you for purchasing the industrial HMI touch panel series of M2I corporation.
Please read this manual carefully to know installing, wiring, operating this equipment for safe use of this
product.
M
I Corporation
2
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea,
Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr
Industrial HMI Touch Panel
TOPRC-Ex Series Hardware Manual
M
I Corporation
2
TOPRC-Ex Series
Hardware Manual
1 / 21
Advertisement
Related Manuals for M2I TOPRC-Ex Series
Summary of Contents for M2I TOPRC-Ex Series
- Page 1 Industrial HMI Touch Panel TOPRC-Ex Series Hardware Manual Thank you for purchasing the industrial HMI touch panel series of M2I corporation. Please read this manual carefully to know installing, wiring, operating this equipment for safe use of this product. I Corporation...
- Page 2 3.6 Antenna Information ..............................8 3.7 Environment Specifications ............................8 3.8 Structure Specifications ..............................8 Chapter 4 Parts Identification and Functions ..........................9 4.1 TOPRC-Ex Series ................................9 Chapter 5 Interface ....................................11 5.1 Serial Interface ................................11 5.2 Ethernet Interface ................................13 5.3 USB Interface ...................................
- Page 3 TOPRC-Ex Series Hardware Manual Chapter 1 Safety Precautions ■ Before using the product To use the product safely and effectively, please read the contents of this manual thoroughly before use. Please keep to the safety precaution, for it is to prevent accidents and potential danger from occurring. Safety precaution is classified into ‘Warning’...
- Page 4 TOPRC-Ex Series Hardware Manual not a defect in LCD characteristics. Do not store or operate in direct sunlight. Direct sunlight can change the properties of the LCD. WARNING – DO NOT CONNECT OR DISCONNECT WHEN ENERGIZED. or equivalent. AVERTISSEMENT – NE PAS CONNECTER OU DÉCONNECTER LORSQUE L'ÉQUIPEMENT EST SOUS TENSION.
- Page 5 TOPRC-Ex Series Hardware Manual ■ Wiring Precautions Be sure the wiring is done correctly by checking the product’s rated voltage and the terminal layout. Incorrect wiring could result in fire, damage or malfunctions. Tighten the terminal screw with the specified torque. If the screws of terminal are loose, it could result in short circuit, fire, malfunctions.
- Page 6 TOPRC-Ex Series Hardware Manual Chapter 2 Overview 2.1 Introduction of Products This industrial HMI touch panel is an industrial control device required in industrial field. It is a device based on RS-232C and RS-422/485, Ethernet which is used for the basic purpose of communication with another device(PLC).
- Page 7 TOPRC-Ex Series Hardware Manual Chapter 3 General Specifications 3.1 Power Specifications Rated voltage DC 24V, Class 2 Input Voltage Range DC 20~28V, Class 2 TOPRC1200WD TOPRC1200WD 01 TOPRC1500WD Power Consumption TOPRC1500WD 01 TOPRC1900WD TOPRC1900WD 01 Voltage endurance DC 24V, within 10㎳...
- Page 8 TOPRC-Ex Series Hardware Manual Transmit Speed 300Mbps@Max Freq. Range 5150Mhz ~ 5725Mhz Standard IEEE 802.11a/n Wi-Fi compliant 5 GHz Spectrum Band 20/40MHz Transmit Speed 300Mbps@Max 2.4G: +6.38dBm (Including Antenna gain), Maximum Power 5G: +15.02dBm (Including Antenna gain) Operation Area 20M or more (*flat-ground communication)
- Page 9 TOPRC-Ex Series Hardware Manual Chapter 4 Parts Identification and Functions 4.1 TOPRC-Ex Series 4.1.1 External Dimension (mm) 모델명 TOPRC1200WD-Ex 321.4 252.4 67.5 TOPRC1200WD-Ex 01 TOPRC1500WD-Ex 406.4 286.4 67.5 TOPRC1500WD-Ex 01 TOPRC1900WD-Ex 477.4 328.4 67.5 TOPRC1900WD-Ex 01 I Corporation 9 / 21 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
- Page 10 TOPRC-Ex Series Hardware Manual 4.1.2 Front Part Names and Specifications Title Description ① TFT 16M Color LCD ② Touch Panel Capacitive Touch ③ Power LED System power status LED ④ USB OTG Project file upload/download (*Internal program managing purpose) ⑤...
- Page 11 TOPRC-Ex Series Hardware Manual 4.1.4 Bottom Part Names and Specifications Title Form Description ① Serial COM1 DSUB9 RS-232C/422/485 serial comm. (select by software) ② Serial COM2 DSUB9 RS-232C/422/485 serial comm. (select by software) ③ ETHERNET Connector RJ45 x 2ch 10BASE-T/100BASE-TX/1000BASE-T, Auto-MDIX ④...
- Page 12 TOPRC-Ex Series Hardware Manual Data Bit 7, 8bit Data Type Parity Bit NONE, ODD, EVEN Parity Stop Bit 1, 2bit Terminating Resisters 100/120Ohm (select by software) Connector DSUB 9pin 5.1.3 COM1 Connector pin number and Signal name Type Pin No.
- Page 13 USB 2.0 Communication Method Interrupt/Bulk/Isochronous Transfer Speed Max 480Mb/s Supportive OS Windows 98SE/2000/XP/VISTA/7/10(32/64bit) M2I manufacturer's cable is recommended (3M), and 1.5M or less Cable Length when purchased separately Connector Type Mini USB B, Female Connecting Method Front, USB OTG connector...
- Page 14 TOPRC-Ex Series Hardware Manual Chapter 6 Installation 6.1 Installation Requirements (1) It should be installed within -10 ~ 50°C and 10 ~ 80% relative-humidity, otherwise the screen may be changed or cause malfunction and damage. (2) Be sure that heat from surrounding equipment does not cause product to exceed its standard operating temperature.
- Page 15 TOPRC-Ex Series Hardware Manual 6.2 Install Procedure Please follow as below explanation to install the product. 6.2.1 Panel Cut-out Make a panel cut which product is mounted and insert the product to the panel form the front side. Making the Panel Cut (Mounting Size) per each model as below Table, Before Installation.
- Page 16 TOPRC-Ex Series Hardware Manual If the clamping screw below is over-tightened, the touch sensor may stop working or malfunction. Tighten to 0.4N.m screwdriver torque. Caution: IP performance cannot be secured if the clamp is not tightened with a tightening force of 0.4N.m.
- Page 17 TOPRC-Ex Series Hardware Manual Chapter 7 Wiring 7.1 Power Cable Wiring (1) The Power cable should have the following specification. Power Cable Specification 0.75~2.5mm (18~12AWG) F.G Cable Specification (14AWG) Conductor type solid or stranded type (use copper conductor only) Bolt torque 0.4N.m...
- Page 18 TOPRC-Ex Series Hardware Manual 7.2 Ground wiring (1) The product has enough anti-noise measure, so except that there are many noises. Specially, the ground is not needed. When doing ground, please refer to the followings. (2) The ground should be the exclusive ground. The ground should be type class 3 ground (ground resistor is less than 100Ω).
- Page 19 Check the touch pad there is no damage, scratch or pollution by eye. 8.3 Problems with the Device a. If there is a problem during operation, stop using it and contact the A/S department of M2I Corporation, which is indicated on the product label.
- Page 20 TOPRC-Ex Series Hardware Manual Chapter 9 Products and Warning Label’s Location Warning Product Manufacturer **Power Battery Operation Temp. Cautions ***Certificates / Protections I Corporation 20 / 21 11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: +82-70-465-3366, Fax: +82-31-465-3355, www.m2i.co.kr...
- Page 21 - TOPRC1200WD, TOPRC1200WD 01 : 24Vdc, 40W, Class 2 - TOPRC1500WD, TOPRC1500WD 01 : 24Vdc, 40W, Class 2 - TOPRC1900WD, TOPRC1900WD 01 : 24Vdc, 40W, Class 2 ***These can be different depends on each model. Before model selection, make sure the details to M2I. Copyright: M2I Corporation 2025.04 www.m2i.co.kr...
Need help?
Do you have a question about the TOPRC-Ex Series and is the answer not in the manual?
Questions and answers