Advertisement
Quick Links
XTOP SERIES Installation Manual
Package Contents
Package contents of XTOP are below. Before using XTOP, please make sure that all of components
are in the package.
* Protection sheet is option content in XTOP04TW.
◆ XTOP Series Model Description
XTOP
08
Series
Display Size
04 : 4.3"
T : TFT Color LCD
05 : 5.7"
S : STN Color LCD
08 : 8.4"
M : STN Mono LCD S : SVGA(800*600)
10 : 10.4"
12 : 12.1"
15 : 15"
Safety Precautions
Products to safely and efficiently use it, please read through the contents of this manuals.
Precautions for the safety of using the products safely and properly will prevent accidents and risk
in advance, so please just do it.
Precautions on Disposal
When you dispose of product and battery, please treat it as industrial wastes. It can create
poisonous substances or explosion.
T
LCD type
Resolution
Q : QVGA(320*240)
V : VGA(640*480)
X : XGA(1024*768)
W: WQVGA(480*272)
WVGA(800*480)
V
-
E
S : S type
E : E type
U : U type
1
XTOP04/07 Only
D
-
E
A : AC power
E : Ethernet
D : DC power
+ CF Card
Advertisement
Related Manuals for M2I XTOP Series
Summary of Contents for M2I XTOP Series
- Page 1 Package contents of XTOP are below. Before using XTOP, please make sure that all of components are in the package. XTOP04/07 Only * Protection sheet is option content in XTOP04TW. ◆ XTOP Series Model Description XTOP Series Display Size LCD type...
- Page 2 Design Precautions Install protection circuit on the outside of Products to protect the entire control system when external power supply or Products have problems. As the malfunction & incorrect result of Products could damage the stability of the entire systems and human body, You must install damage preventing interlock circuit such as emergency stop, protective circuits, positioning upper and lower limit switch and interlock for forward/reverse operation.
- Page 3 General Precautions Do not strike the touch screen with a hard or pointed object (such as drill, driver, pen, etc) or press on the touch screen with too much force. It may cause malfunction of touch panel by damaged front sheet. Do not use or store in severe vibration environment.
- Page 4 The Connector Pins and Signals of COM1(6Pin) with RS-232C Interface The contents of Below Table are corresponding to all XTOP tyoe. TYPE Pin No. Signal Direction Contents 6Pin Female RD (RxD) Input Project file Receive (COM1) SD (TxD) Output Project file Send (COM1) Signal Ground The Connector Pins and Signals of COM2(15Pin) with RS-232C Interface The contents of Below Table are corresponding to XTOP05MQ/05TQ/08TV/08TS S type, E type, and XTOP07 U type.
-
Page 5: Signal Direction
The Connector Pins and Signals of COM2(9PIN) with RS-232 Interface of RS-422 Terminal TYPE Signal Direction Contents 9Pin Female RD (RxD) Input RS232C Date Receive SD (TxD) Output RS232C Data Send Signal Ground Note: The RS-232 Pins(No.2,3Pin) in the RS-442 Terminal of COM2 Port can be used to download Project file such as COM1 Port.) Serial Interface RS-422/485 For Serial Interface with RS-422/485, Product should be connected according to the below items. - Page 6 Type Pin No. Signal Direction Contents 9Pin Female RDA(RD+) Data Receive(+) RDB(RD-) Data Receive(-) Signal Ground SDA(SD+) Data Send(+) SDB(SD-) Data Send(-) Ethernet Communication and Connection Ethernet Specification Item Specification Ethernet Method 10BaseT / 100BaseT Speed 10M / 100Mbps Communication Method Base Band Maximum Segment Length 100m (Hub between Node(XTOP)
-
Page 7: Specification
USB Interface OHCI Specification Version 1.0 Communication Control/Bulk Method Transfer Speed 500Kb/s –10Mb/s USB Storage (Only M2I Option product is available, Only FAT File Support Device Format Available)) USB Printer (HP PCL Level 3) USB Device Hardware Item Specification USB Interface USB Specification Version 1.1... - Page 8 Front Part Names and Specifications Title Feature 05MQ 05TQ-S 08TV-S Model 08TS-S 05MQ-E 05TQ-E 08TV-E TYPE STN 16 GLAY MONO TFT 65536 COLOR 260cd/㎡ 450cd/㎡ 450cd/㎡ Brightness 350cd/㎡ 230cd/㎡ 400cd/㎡ 400cd/㎡ Screen Size 14cm/5.7 Inch 21cm/8.4 Inch Resolution 320X240 640X480 800x600 Touch Touch Type...
- Page 9 [Table1. Outer Dimension] Model FRONT SIDE REAR XTOP10TV-E 199.9 49.8 257.9 199.9 XTOP10TV/TS-S 226.4 292.4 226.4 XTOP12TS-S 244.3 303.8 244.3 XTOP15TX-S 296.5 283.5 352.8 283.8 Front Part Names and Specifications Title Feature Model 10TV-S 10TS 12TS-S 15TX-S 10TV-E TYPE TFT 65,536 Color LCD 380cd/㎡...
- Page 10 XTOP04TW-UD [Pic1. Front View] [Pic2. Side View] [Pic3. Rear View] XTOP07TW-UD [Pic1. Front View] [Pic2. Side View] [Pic3. Rear View] [Table1. Outer Dimension] Model FRONT SIDE REAR XTOP04TW-UD 92.3 118.3 92.3 XTOP07TW-UD 64.5 57.5 194.5 Front Part Names and Specifications Title Feature Model...
- Page 11 Rear Part Names and Specifications Title No. of 설명 Rubber Packing Shock Absorber for Panel Mounting Contrast Volume Contrast Adjust In this model, Contrast Adjust is possible in [Setup] in Menu mode RS-232C, 422 Connector XTOP04: 9 pin, XTOP07: 15 pin PS/2 Connector or USB For Download/Upload, Serial or USB comm.
- Page 12 The Size of Panel Cut(Mounting Place) Making the Panel Cut (Mounting Size) per each XTOP Series according to below Table, Before Install the Product. Measure:[mm] Model X(Width) Y(Height) Detail Model Thickness XTOP05 Series XTOP05MQ/05TQ S type, E type XTOP08 Series...
- Page 13 Window” is appeared. This Self Test is simple Diagnosis with sample protocol in communication between PLC and XTOP Series. This test can identify the following. First, The status of wiring with Target PLC, Second, The suitability of PLC Communication Setup, Third, Whether the communication parameters be equally set between PLC and XTOP communication setup.
- Page 14 Please wiring COM1/COM2 Port as below Pic., Before testing the Self Diagnosis of each COM Port in the Main Menu. COM1 Port Wiring COM2 Port Wiring(RS-232C) Note: As stated above wiring of Each COM2 Port is set by RS-232C. So It is essential to change the COM2 Serial Signal Level No.5 Item to “RS-232C”...
- Page 15 When the buzzer sound is unable to confirm because of the noise surroundings, the power of touch shall be allowed while continuously press and off on the lower part of the logo. Screen Calibration steps of XTOP Series When the Analog touch glass don’t work properly, for correcting the touch command, you have the touch pad be calibrated.