Subscribe to Our Youtube Channel
Related Manuals for Ametek SWI U00 E Series
Summary of Contents for Ametek SWI U00 E Series
- Page 1 U00XE ULTRASONIC LEVEL SWITCH INSTALLATION AND OPERATIONS MANUAL Ultrasonic Liquid Level Switches For Models: U002E, U003E & U004E For Hazardous Locations ISO 9001:2008 CERTIFIED...
-
Page 2: Warranty
The following styles are Notice of Copyright and Limitations used for notes, cautions and warnings: Copyright ©2022 AMETEK Magnetrol, LLC All rights reserved. Notes Solutions With Innovation reserves the right to make Notes contain information that augments or clarifies an operating step. -
Page 3: Table Of Contents
U00XE ULTRASONIC LEVEL SWITCH For Hazardous Locations TABLE OF CONTENTS 1.0 Installation 1.1 Unpacking................4 1.2 Electrostatic Discharge Handling Procedure....4 1.3 Before You Begin...............4 1.3.1 Site Preparation............4 1.3.2 Equipment and Tools..........4 1.4 Mounting................5 1.4.1 Horizontal Installation..........5 1.4.2 Vertical Installation...........5 1.4.3 Nozzle or Pipe Installation........5 1.5 Wiring..................6 1.5.1 U002E: Current Shift Output.........6 1.5.2 U003E: Relay Output..........6... -
Page 4: Installation
1.0 INSTALLATION This section provides detailed procedures on properly installing and configuring the U00XE Ultrasonic Liquid Level Switch for Hazardous Locations. CAUTION! IF THE EQUIPMENT IS USED IN A MANNER NOT SPECIFIED BY THE MANUFACTURER, PROTECTION PROVIDED BY THE EQUIPMENT MAY BE IMPAIRED. 1.1 UNPACKING Unpack the instrument, carefully. -
Page 5: Mounting
1.4 MOUNTING The U002E, U003E and U004E Ultrasonic Liquid Level Switches can be mounted in a variety of positions. By ensuring the vertical orientation of the transducer gap, the unit will facilitate maximum performance in difficult applications. 1.4.1 Horizontal Installation 1 Apply thread tape or pipe compound onto the unit’s mounting thread. -
Page 6: Wiring
1.5 WIRING WARNING! DO NOT DISCONNECT THE EQUIPMENT UNLESS THE POWER IS SWITCHED OFF. DO NOT ATTEMPT TO WIRE THE EQUIPMENT UNLESS THE POWER IS SWITCHED OFF. CAUTION! ALL WIRING, CONDUIT AND ELECTRICAL FITTINGS MUST CONFORM TO ALL LOCAL ELECTRICAL CODES CORRESPONDING TO THE INSTALLATION LOCATION. 1.5.1 U002E: Current Shift Output •... -
Page 7: U004E: Relay Output With Fail-Safe Option
1.5.3 U004E: Relay Output with Fail-Safe Option • The six (6) wiring terminations for the U004E are 18 AWG. • Connect the wires to field wiring that is 14 to 22 AWG. Field Wiring Connection: 1 Install the conduit into the 3/4” NPT connection. 2 Use an approved seal fitting to prevent moisture from entering the internal switch. -
Page 8: Preventative Maintenance
2.0 PREVENTATIVE MAINTENANCE Periodic inspections are necessary to maintain the proper functionality of the U00XE Ultrasonic Liquid Level Switch. The switch is an extremely compact level device with its electronics enclosed directly above the stainless steel transducer inside the extension piece. A systematic program of preventative maintenance should be implemented at the time of installation. -
Page 9: Reference Information
3.0 REFERENCE INFORMATION This section illustrates an overview of the U00XE Ultrasonic Liquid Level Switch operation, as well as information on troubleshooting common problems, agency approval listings and detailed physical, functional and performance specifications. 3.1 DESCRIPTION The U002E, U003E and U004E Ultrasonic Liquid Level Switches are compact integral units that utilize pulsed signal technology to perform high or low level measurement in a wide variety of fluid applications. -
Page 10: Troubleshooting
3.3 TROUBLESHOOTING The U00XE Ultrasonic Liquid Level Switch is designed and manufactured for trouble-free performance across a wide range of operating conditions. Common problems are discussed in terms of their symptoms and recommended corrective actions. WARNING! DO NOT CONNECT OR DISCONNECT THE EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS. -
Page 11: Agency Approvals
3.4 AGENCY APPROVALS AGENCY APPROVED MODEL(S) FILE NUMBER AREA CLASSIFICATION EXPLOSION-PROOF: U00aEb08Cd 3046984 CLASS I, DIV. 1, GROUPS C & D DUST IGNITION-PROOF: CLASS II/III, DIV. 1, GROUPS E, F & G, T4 TA = -40° C TO +85° C INDOOR/OUTDOOR RATING: 4X U00X-E 3039761... -
Page 12: Physical
3.5.2 Physical ¾” NPT CONDUIT ¾” NPT ¾” NPT CONDUIT CONDUIT 1 ⅜” HEX 1 ⅜” HEX 4 ⅞” 1 ⅜” HEX 4 ⅞” 4 ⅞” U002E U003E U004E ¾” NPT ¾” NPT MOUNT MOUNT ¾” NPT MOUNT “LO” “LO” “LO”... -
Page 13: Notes
3.7 NOTES U00XE ULTRASONIC LIQUID LEVEL SWITCH FOR HAZARDOUS LOCATIONS... -
Page 14: Service Policy
ASSURED QUALITY & SERVICE COST LESS Service Policy Return Material Procedure Owners of Solutions With Innovation products may In order to efficiently process any returned materials, it is essential that a Return Material Authorization (RMA) number request a return of the product, or any part of the product for complete rebuilding or replacement.
Need help?
Do you have a question about the SWI U00 E Series and is the answer not in the manual?
Questions and answers