Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Dog trace d-mute ONE
Summary of Contents for Dog trace d-mute ONE
- Page 1 d-mute Elektronický obojek proti štěkání Elektronisches Anti-Bell-Halsband Electronic no bark collar Collar antiladridos electrónico Collier électronique anti-aboiement Elektronikus ugatásgátló nyakörv Collare elettronico antiabbaio Elektroniczna obroża antyszczekowa...
- Page 2 ONE – chapter 5 Charging – chapter 6.2 Charging = orange LED on Charging complete = LED off...
- Page 3 Turn on – chapter 6.4 Select Mode – chapter 6.5 < 0.5 s > 1 s Number of beeps Mode Level correction Increasing tone / On / Off — Decreasing tone Auto soft Impulse soft Auto hard Impulse hard Tone —...
- Page 4 Select sensitivity – chapter 6.6 Number of beeps Sensitivity The lowest The highest Fitting the collar – chapter 7 Impulse test – chapter 8...
-
Page 5: Table Of Contents
N E N CONTENTS 1. Declaration of conformity ......27 2. Important notices ........27 3. -
Page 6: Declaration Of Conformity
DECLARATION OF CONFORMITY The manufacturer VNT electronics s.r.o. declares that the Dogtrace d-mute ONE electronic No Bark Collar complies with the Council of Europe Directive 2014/53/EC and conforms to all applicable standards. More on www.dogtrace.com. 2. IMPORTANT NOTICES Please read the instructions carefully before use. Keep the instructions for future reference. -
Page 7: Ecma
Use a 5 - 5.5 V DC charging adapter to charge the battery in the receiver. Dispose of the used battery or batteries in a designated place. 3. ECMA VNT electronics s.r.o. is an active member of the ECMA (Electronic Collar Manufacture Association), which represents the highest quality manufacturers of electronic training aids for dogs. -
Page 8: Preparation Of Equipment
- this will ensure better transmission of stimulation impulses. 6.2 Charging The d-mute ONE no bark collar contains a Li-Pol battery. Before using the device for the first time, the battery must be recharged. 1. Connect the power cord with clip to the device as shown in Figure 2 on page 2. -
Page 9: Checking The Battery Status
(Fig. 1/4 on page 2). If the red LED is flashing, the collar is discharged and needs to be charged. Do not leave the d-mute ONE in a discharged state for an extended period of time. Damage to the battery could occur. -
Page 10: Setting The Collar Mode (Acoustic And Stimulation Pulse)
6.5 Setting the collar mode (acoustic and stimulation pulse) When switched on, the collar automatically switches to automatic mode (mode 1). In this mode, when the dog barks, the degree of stimulation pulse is automatically increased gradually. The correction mode can be switched to another mode as follows: 1. -
Page 11: Adjusting The Sensitivity Of The Bark Sensor
6.6 Bark sensor sensitivity setting The d-mute ONE collar detects barking with a special sensor that reacts to the vibration of the dog's vocal cords when barking (sometimes growling and whining) and does not react to the sound made when barking. This prevents bark detection if another dog is barking nearby. -
Page 12: Fitting The Collar On The Dog
7. FITTING THE COLLAR ON THE DOG The dog must have the device fitted to the base of the neck (vocal cords) so that the receiver can correctly detect the barking - Figure 6 on page 4. The harness (collar) must be tight enough so that it cannot move on the dog's neck, but at the same time it must not strangle the dog. -
Page 13: Maintenance
4. If the problem persists, contact your dealer. 9. MAINTENANCE The d-mute ONE collar is waterproof only if the seal in the top cover of the collar is in good condition. When replacing the battery, check the condition of the seal and remove any dirt from the seal. Tighten the screws of the top cover with reasonable force. -
Page 14: Technical Data
10. TECHNICAL DATA Power ............Li-Pol battery Battery life per charge .
Need help?
Do you have a question about the d-mute ONE and is the answer not in the manual?
Questions and answers