Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for CIRCLE FITNESS Sp7B
Summary of Contents for CIRCLE FITNESS Sp7B
- Page 1 Owner’s Manual Sp7B Indoor Cycle...
- Page 2 ATTENTION: S831601-000-00 Sp7B 10807 Read instructions carefully, failure to do so may cause permanent damage to your bike. Please verify that all parts associated with this product are in good condition and accounted for. During the assembly process please be sure to follow each step accordingly as it has been...
-
Page 3: Safety Information
SAFETY INFORMATION: 1. Keep children and pets away from this equipment at all times. DO NOT leave them unsupervised in the room where the machine is kept. 2. If you experience dizziness, nausea, chest pains or any other symptom while using this machine STOP the exercise. - Page 4 CAUTION: During assembly it is recommended that all bolts be tightened by hand, upon completing assembly, bolts should then be properly secured using the wrench provided. To avoid injury, check bolts carefully before use. Assembly Step one Attach the rear foot tube (14) first by lifting up the rear of the frame and sliding the rear foot tub under the frame.
- Page 5 Step three Insert the seat post (43) into the seat tube on the frame to the desired height and secure with the release lever (6). Attach the saddle (1) onto seat slider (42), and secure the saddle by tightening the nuts on both sides of the saddle clamp on the underside of the saddle, use wrench.
-
Page 6: Right Pedal
Right Pedal Please make sure pedal in your hand is the right pedal before Installation. Turn the brake knob all the way to the right until the crank arms are immobilized. Please refer to the figure. Align the right pedal with right crank at 90 degree. Gently insert the pedal in the crank arm. - Page 7 Adjusting the resistance Adjust the exercise resistance on the spinning bike using the brake knob (24) to loosen (-) or tighten (+). flywheel should rotate freely without resistance when you loosen (-) the brake system fully. More experienced riders may wish to increase the overall resistance by tightening (+) the brake system.
- Page 8 Instruction Handlebar and seat adjustment. It is important that the handlebar and seat are set at the correct height for your body. Ask your instructor for assistance. Adjusting the handlebar height-Undo the release lever that is located where the handlebar post fits into the frame. Slide the handlebar post up or down to the required height and retighten the release lever.
-
Page 9: Exploded Drawing
Exploded Drawing... -
Page 10: Part List
Part list Name Unit Name Unit Alloy bind clamp ( L ) Flywheel Security nut Spring for release lever Flywheel bearing Alloy bind clamp ( R ) Flywheel washer Washer for release lever Flywheel nut Release lever Flywheel washer Foot tube nut Moving wheel Foot tube washer Plastic washer for release lever... -
Page 11: Maintenance Chart
BB bearing Inner belt guard BB Axle with plate Left axle rubber cover Console Bottle cage Screw for bottle cage End cap for handlebar post Maintenance Chart Like any other mechanical cycling device, the bike should be regularly maintained. DESCRIPTION Daily Weekly Monthly Quarterly Annually Keep machine clean: Wipe machine... -
Page 12: How To Change Battery
How to change battery﹕ 1. Open battery cover and insert 2 AAA or 2 UM-4 batteries. 2. Properly put back battery cover. 3. Under regular condition, warranty of battery is one year. 4. If the LCD shows partial display, please take out batteries, wait for 15 seconds and insert again. 5. -
Page 13: Function And Operation
UP+DOWN： 1. Press UP key and DOWN key at the same time for 3 seconds to start “AUTO SCAN” function. 2. Under the condition of setting exercise values, Press UP key and DOWN key at the same time for 1 second to remove the values. Function and Operation Auto ON/OFF The monitor automatically starts working once the user starts to do the exercise on the machine. - Page 14 Sp7B Indoor Cycle www.circlefitness.com...
Need help?
Do you have a question about the Sp7B and is the answer not in the manual?
Questions and answers