Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Edge-Core ECWO5213-L
Summary of Contents for Edge-Core ECWO5213-L
- Page 1 Handbook ECWO5213-L Access Point...
-
Page 2: Copyright Notice
Handbook ECWO5213-L Access Point ENGLISH Copyright Notice This document is protected by USA copyright laws and other laws. Besides, the document is the property of Edgecore Networks Corporation. You may not copy, reproduce, distribute, publish, display, perform, or modify any part of this publication in any form or by any means without prior written permission from Edgecore Networks Corporation. - Page 3 Handbook ECWO5213-L Access Point ENGLISH FCC CAUTION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 4 5150~5825 10.5 PIFA IPEX 5150~5825 10.2 CE CAUTION Hereby, Edgecore Networks Corporation. declares that the radio equipment type ECWO5213-L is in compliance with Directive 2014/53/EU. Frequency Range and Transmit Power Frequency range (MHz) Max. transmit power (dBm) 2412-2472 23 dBm...
- Page 5 Handbook ECWO5213-L Access Point ENGLISH Model – ECWO5213-L The device has been tested and passed the requirements of the following standards, and hence fulfills the EMC and safety requirements of RED within the CE marking requirement. Radio: EN 300 328 V2.1.1, EN 301 893 V2.1.1 ...
- Page 6 Besides ECWO5213-L’s PoE uplink port is able to receive power from Power over Ethernet (PoE) sourcing devices, its LAN port also supports PoE with 802.11at standard which make network deployment more convenient and easier.
-
Page 7: System Overview
ECWO5213-L Back ECWO5213-L status. The Power LED will start blinking when the Power LED ECWO5213-L is booting. After finishing booting, the Power LED will always LAN1 LED Uplink status. The LAN1 LED will light up when there is traffic passing through the LAN1 port. - Page 8 LAN1 (PoE) Port gateway, or directly to the Internet. 802.3at PoE is also supported. Ventilation Valve Due to extreme weather conditions, water vapor in the ECWO5213-L may condense. The valve allows ventilation to prevent moisture buildup within the ECWO5213-L. The ports for connections with LAN side devices.
-
Page 9: Hardware Installation
Please follow the steps mentioned below to install the hardware of ECWO5213-L: 1. Place the ECWO5213-L at the best location. The best location for ECWO5213-L is usually at the center of your intended wireless network. Wall mount 1. Secure screws on the wall. - Page 10 2. Connect the ECWO5213-L to your network device. Connect one end of the Ethernet cable to the LAN1 (PoE) port of ECWO5213-L and the other end of the cable to a switch, a router, or a hub. ECWO5213-L is then connected to your existing wired LAN network.
-
Page 11: Getting Started
1. To access the web management interface, connect the administrator PC to the LAN port of ECWO5213-L via an Ethernet cable. Then, set a static IP address on the same subnet mask as ECWO5213-L in TCP/IP of your PC, such as the following example: IP Address: 192.168.1.100... - Page 12 Handbook ECWO5213-L Access Point ENGLISH 4. After a successful login into ECWO5213-L’s Web user interface (Web UI), a System Overview page of web management interface will appear, as depicted below. The Web Management Interface - System Overview Page Congratulations! Now, Edgecore ECWO5213-L is installed and configured successfully.
Need help?
Do you have a question about the ECWO5213-L and is the answer not in the manual?
Questions and answers