Subscribe to Our Youtube Channel
Related Manuals for H-KING Flycat V2
Summary of Contents for H-KING Flycat V2
- Page 1 INSTRUCTION MANUAL 1042mm EDF JET with pre-installed 70mm Fan, Motor, ESC, Servos, and Retracts.
-
Page 2: Table Of Contents
MANUAL CONTENTS Introduction and Specifications ----------------------- Warning & Safety Notes -------------------------- ---3/4 Contents ------------------------------------------- Assembly ---------------------------------------- 6/14 Center of Gravity ------------------------------------ Control Throws ------------------------------------- ESC Set Up ----------------------------------------- Flying Tips ----------------------------------------- Recommended Accessories ----------------------- 19/21... -
Page 3: Introduction And Specifications
V2 version. The Flycat V2 has been updated with a new 12-blade 70mm fan unit driven by a powerful 2860-2100KV inrunner motor, dual rudders for added control and agility, a set of pre-installed electronic retracts, and a brand new high-viz color scheme. -
Page 4: Warning & Safety Notes
Warning on the use of LiPo batteries and their chargers. Warnings and Safety notes... -
Page 6: Contents
FLYCAT V2 CONTENTS: 1. Fuselage 2. Wings 3. Tailbooms 4. Horizontal stabilizer 5. Accessories... -
Page 7: Assembly
GENERAL ASSEMBLY Please note: Before you glue together any parts that have paint on the joints, rough them up first with sandpaper to achieve a better bond. 1. Using a slow cure CA or a similar apply the glue to the area of the fuselage where one of the plywood wing retaining tongues is located. - Page 8 3. Repeat this process with the other 3 plywood tongues. 4. Glue into place the 4 foam in-fills on top of the plywood tongues.
- Page 9 5. This picture shows all 4 foam in-fills in place. 6. Apply slow setting CA or a similar glue into the recess on the fuselage side of the tail boom that does not have the cut-out in the vertical stabilizer.
- Page 10 7. Slide the tail boom over the wing root of the fuselage as shown and glue into place. 8. Please ensure the aileron servo connector is pulled through the wing root.
- Page 11 9. The elevator & rudder servo extension leads are already installed in the tailboom. Connect these to the leads in the fuselage slot and press into place, secure with either a drop of glue, or some colored tape. 10. Apply some slow cure CA into the slot for the horizontal stabilizer to be glued into.
- Page 12 11. Fit the horizontal stabilizer into the slot in the vertical stabilizer and allow the glue to set. Please ensure the assembly stays square as the glue sets. 12. Feed the elevator servo lead into the slot in the vertical stabilizer and connect in to the socket in the cut-out as shown.
- Page 13 13. Apply CA glue to the recess in the cut-out and glue into place the triangular cover supplied. 14. At this point, follow the steps of gluing in place the first tailboom and glue into place the second one, including gluing in the horizontal stabilizer.
- Page 14 16. Slide the wing spar into the pre-installed tube in the fuselage wing root. 17. Then slide the entire wing into the wing root until it is fully seated and the holes line up with those in the plywood tongues.
- Page 15 18. Screw the supplied PK screws through the plastic wing fixings and into the plywood tongues. 19. Repeat this entire process to fit the other wing. 20. Install your chosen receiver in the recess at the rear of the battery compartment, and then install your 6S battery as shown.
-
Page 16: Center Of Gravity
C of G Position: C of G should be 510mm ± 5mm from the nose of the Flycat V2. Adjust the position of the battery to achieve the correct balance... -
Page 17: Control Throws
CONTROL THROWS LOW-HIGH Your Flycat V2 should now be finished and ready to fly. -
Page 18: Esc Set Up
SETTING THE ESC The Flycat V2 is fitted with the Aerostar 80A RVS G2 instant reversing electronic speed controller. Setting the reverse on the ESC would be ideal if you are flying from a hard surface to shorten the landing run. -
Page 19: Flying Tips
Once you have your Flycat V2 flying well it will perform as if it is on rails, it's fast, smooth and manoeuvrable. You will be able to fly all the usual jet like aerobatics with ease and it looks really great in the sky. -
Page 20: Recommended Accessories
RECOMMENDED ACCESSORIES Turnigy/FrSky TWIN X14 ACCESS Turnigy TGY-i6 Mode 2 AFHDS 2.4GHz Transmitter (Orange) Transmitter and 6CH Receiver SKU: 9236720209 SKU: 9114000020-0 FrSky TW R8 Dual 2.4GHz 8ch TW Turnigy iA6 Receiver 6CH 2.4G AFHDS Protocol SBUS/FBUS/S.Port Receiver 2A Receiver SKU: 9236720012 SKU: 9114000008-0 Recommended Accessories... - Page 21 RECOMMENDED ACCESSORIES Turnigy Heavy Duty 4000mAh 6S Turnigy Graphene Panther 5000mAh 60C Lipo Battery Pack w/XT90 6S 75C Battery Pack SKU: 9067000386-0 SKU: 9067000375-0 Turnigy Heavy Duty 3300mAh Turnigy Graphene 4000mAh 6S 45C 6S 60C LiPo Pack w/XT-90 LiPo Pack w/XT90 SKU: 9067000242-0 SKU: 9067000146-0 Turnigy Nano-Tech Plus...
- Page 22 RECOMMENDED ACCESSORIES ToolkitRC M6DAC Dual 1~6S 15A 350W HOTA H6 Pro AC/DC 200W AC/DC Balance Charger/Discharger AC/700W DC 1~6S Smart Charger UK Plug SKU: 9989320005 US Plug SKU: 9466000020-2 US Plug SKU: 9989320079 SKYRC IMAX B6 V2 60W 6A 1~6S HOTA P6 2 x 300W 1~6S Dual DC Charger/Discharger Smart Charger/Discharger (DC Only)
Need help?
Do you have a question about the Flycat V2 and is the answer not in the manual?
Questions and answers