Subscribe to Our Youtube Channel
Related Manuals for Vivo STAND-V002R Series
Summary of Contents for Vivo STAND-V002R Series
- Page 1 Dual Vertical Monitor Desk Mount STAND-V002R Series Assembly Manual Individual Product SKUs STAND-V002R STAND-V002RW...
- Page 2 If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo-us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Failure to report missing parts within 30 days may result in denial of free replacement.
-
Page 3: Package Contents
Package Contents A (x1) B (x1) C (x1) D (x1) Lower Pole Upper Pole Clamp Grommet Plate E (x2) F (x1) G (x2) H (x1) I (x5) VESA Bracket Pole Connector Cable Clip Pole Cover J (x1) Support Plate Included Hardware & Tools T-A (x1) T-B (x1) M-A (x8) - Page 4 Assembly Steps STEP 1 Option 1: Clamp Installation Remove adhesive backing from Pads (I) and apply them evenly to the inside of Clamp (C). Thread Lower Pole (A) into Clamp and secure by tightening the set screws using 3mm Allen Wrench (T-A).
- Page 5 Option 2: Grommet Installation Use a Phillips screwdriver to remove the screw from Clamp Bolt (C1). Remove adhesive backing from Pads (I) and apply them evenly to the bottom of Grommet Plate (D). Thread Lower Pole (A) into Grommet Plate (D) and secure by tightening the set screws using 3mm Allen Wrench (T-A).
- Page 6 STEP 2 Slide one VESA Bracket (E) onto Lower Pole (A) and secure by tightening the back screw using 5mm Allen Wrench (T-B). Ensure the open holes on VESA Brackets are on the top. The back screw may need to be loosened before sliding onto Pole.
- Page 7 STEP 3 Thread Pole Connector (F) onto Lower Pole (A), then thread Upper Pole (B) into Pole Connector. Secure by tightening the set screws on Pole Connector using 3mm Allen Wrench (T-A). Slide on the remaining Cable Clip (G). Poles Won’t Thread Into Connector? If Poles (A,B) are difficult to thread into Pole Connector, the two set screws may need to be...
- Page 8 STEP 4 Slide the remaining VESA Bracket (E) onto Upper Pole (B) at the desired height and secure by tightening the back screw using 5mm Allen Wrench (T-B). Ensure the open holes on VESA Brackets are on the top. The back screw may need to be loosened before sliding onto Pole.
- Page 9 STEP 5 Thread two appropriate Screws (M-A or M-B) with M5 Washers (M-C) into the top two holes of each monitor leaving 3mm of threading exposed. Place monitors onto the heads of VESA Brackets (E). Secure monitors using additional Screws (M-A or M-B) with M5 Washers (M-C). Tighten all screws using a Phillips screwdriver.
- Page 10 STEP 6 Adjust the vertical tilt tension as desired using 6mm Allen Wrench (T-C) as shown. +45° -45° Manage cables using Cable Clips (G). Store Allen Wrenches (T-A, T-B, T-C) in Cable Clips for future adjustments.
- Page 11 Adjust as Desired 360° 360° 360° 360° 360° 360°...
- Page 12 Need Help? We’re Here For You Monday-Friday from 7am-7pm CST Saturday 8am-4pm CST Email Us Chat with Live Agent Give Us a Call help@vivo-us.com www.vivo-us.com 309-278-5303 ext. 1 FOR MORE GREAT VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM VIVO-us @vivo_us @VIVOus VIVO...
Need help?
Do you have a question about the STAND-V002R Series and is the answer not in the manual?
Questions and answers