Advertisement
Advertisement
Table of Contents
Related Manuals for Uplus Lighting LM05
Summary of Contents for Uplus Lighting LM05
- Page 1 User manual LM05 Please read the instructions carefully before use...
-
Page 2: Table Of Contents
TABLE OF CONTENTS 1. Safety Instructions……………………………………………………………………………3 Technical Specifications………………………………………………………………………4 Control Menu ……………………………………………………………………………………4-8 DMX Channels …………………………………………………………………………………9-13 Trouble Shooting…………………………………………………………………………………14 Fixture Cleaning………………………………………………………… ………………………14 STATEMENT The product has well capability and intact packing when leave factory. All of the user should comply with warning item and manual, any misuse cause of the damages are not included in our guarantee, and also can not be responsible for any malfunction &... -
Page 3: Safety Instructions
1.Safety Instructions Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. Unpack and check carefully there is no transportation damage before using the unit. •... -
Page 4: Technical Specifications
2.Technical Specifications Rated voltage: AC110-220V Shaking head laser +LED dye light Rated frequency: 50 ~ 60Hz Rated power: 300W Laser color: RGB full color Laser power: RGB 5W Laser light source: R1w/638nm G1w/525nm B3w/447nm Laser pattern: 256 laser animation pattern Modulation signal: TTL modulation (analog modulation) Scanning system: galvanometer scan 30KPPS Scanning Angle: plus or minus 20°... -
Page 5: Control Menu
3.Control Menu Interface Name Power input interface Power switch Ground DB25 ILDA interface (IN/OUT) DMX512 interface (IN/OUT) SD card Safety key E-stop control (optional) NO light/ normal light,The device system is in the dead state indicating light Flash : The equipment system is running normally Green No light or all light:The device system is in a dead state... - Page 6 Using the touch button and LCD menu display function, the menu operation is simple and easy to use, and the system software is automatically loaded when the system is turned on, and the main menu interface is displayed. Use the ▲UP、▼DOWN buttons to select the required function menu icon. Press the ●ENTER、MENU buttons to confirm the selected function or return to the previous menu.
- Page 7 GREEN BLUE Operation Turn on ILDA and only receive ILDA signal. The device will not ILDA mode ON/OFF emit light when running in other modes. Value setting program has a built-in console, (CH1-CH27 can restore the factory settings and Use mode customize the value of save the data, if the data is each channel of the...
- Page 8 card cannot be read The reason for the error is that the communication control board is not powered on ON/OFF error or the chip is broken or there is a problem with the signal line display hardware Device status display software Hardware control Software control The reason for the error is that the...
-
Page 9: Dmx Channels
4.DMX Channels 20CH Channel Description Value Description 0～255 horizontal motor horizontal motor horizontal motor 0～255 horizontal motor 16Bit 16Bit 0～255 vertical motor vertical motor vertical motor 16Bit 0～255 vertical motor 16Bit Laser ON/Off 1～255 On From 1-100% 0～26 Pattern Model Pattern Effect 27～127 Auto Model... - Page 10 0～127 Gobo Big to Small CH14 Zoom 128～255 Zoom Speed Choose Wave Speed Choose 1～127 Pan wave CH15 Wave Speed Choose 128～255 Tilt Wave CH16 1～255 Wash Dimmer Wash Bright Choose 1～255 CH17 Strobe Strobe Speed Choose CH18 1～255 Color Choose 5 Data/Effect CH19 Auto Speed...
- Page 11 CH11 0～255 Color segmentation Color segmentation Effect Choose 0～127 Line Scan Speed Line Scan Speed Choose CH12 Point Scan Speed 128～255 Point Scan Speed Choose 0～127 Rotate Z Angle Choose CH13 Rotate Z 128～255 Rotate Z Speed Choose 0～127 Rotate X Angle Choose CH14 Rotate X 128～255...
- Page 12 Built in effect list...
-
Page 14: Trouble Shooting
5.Trouble Shooting Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting: A. The unit does not work, no light and the fan does not work 1. Check the connection of power and main fuse. 2.
Need help?
Do you have a question about the LM05 and is the answer not in the manual?
Questions and answers