Related Manuals for Avalue Technology NUC-RPU
Summary of Contents for Avalue Technology NUC-RPU
- Page 1 NUC-RPU 13th Generation Intel® Raptor Lake-U Fanless Ultra Slim System Quick Reference Guide Ed –13 June 2024 Copyright Notice Copyright © 2024 Avalue Technology Inc., ALL RIGHTS RESERVED. Part No. E2017JAS1A0R...
- Page 2 NUC-RPU Document Amendment History Revision Date Comment June 2024 Avalue Initial Release 2 NUC-RPU Quick Reference Guide...
-
Page 3: Declaration Of Conformity
For detailed information, please always refer to the electronic user's manual. Copyright Notice © 2024 by Avalue Technology Inc. All rights are reserved. No parts of this manual may be copied, modified, or reproduced in any form or by any means for commercial use without the prior written permission of Avalue Technology Inc. - Page 4 ㆍDescription of your software (operating system, version, application software, etc.) ㆍA complete description of the problem ㆍThe exact wording of any error messages To receive the latest version of the user’s manual; please visit our Web site at: www.avalue.com 4 NUC-RPU Quick Reference Guide...
- Page 5 On the other hand, if the new product defect is resulting from incorrect configuration or erroneous use by the user instead of any problem of the hardware itself, the customer will also be requested to pay for relevant handling fees. NUC-RPU Quick Reference Guide...
- Page 6 Lacking detailed statement of fault steps also makes the problem hard to be identified, sometimes resulting in second-time repairs. 6 NUC-RPU Quick Reference Guide...
- Page 7 Product has been altered or its label of the serial number has been torn off. • Product functionality issues resulting from improper use by the user, unauthorized dismantle or alteration, unfit operation environment, improper maintenance, accident NUC-RPU Quick Reference Guide...
- Page 8 If the customer demands an additional maintenance analysis report, a service fee of various level will be charged depending on the warranty status. In case the analysis result shows that the defect attributes to Avalue’s faulty design or process, the analysis fee will be exempted. 8 NUC-RPU Quick Reference Guide...
-
Page 9: Safety Instructions
9. Position the power cord so that people cannot step on it. Do not place anything over the power cord. 10. All cautions and warnings on the equipment should be noted. 11. If the equipment is not used for a long time, disconnect it from the power source to NUC-RPU Quick Reference Guide... - Page 10 The equipment has obvious signs of breakage. 14. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. 15. Equipment intended only for use in a RESTRICTED ACCESS AREA. 10 NUC-RPU Quick Reference Guide...
-
Page 11: Explanation Of Graphical Symbols
A NOTE provides additional information intended to avoid Note inconveniences during operation. Direct current. Alternating current Stand-by, Power on FCC Certification CE Certification Follow the national requirements for disposal of equipment. Stacking layer limit This side up NUC-RPU Quick Reference Guide 11... - Page 12 NUC-RPU Fragile Packaging Beware of water damage, moisture-proof Carton recyclable Handle with care Follow operating instructions of consult instructions for use. 12 NUC-RPU Quick Reference Guide...
-
Page 13: Disposing Of Your Old Product
EXPLOSION ou une fuite de liquide ou de gaz inflammable. - UNE BATTERIE soumise à une pression d'air extrêmement basse pouvant entraî ner une EXPLOSION ou une fuite de liquide ou de gaz inflammable. NUC-RPU Quick Reference Guide 13... -
Page 14: Table Of Contents
2.2 Powering On the System ..................29 2.3 Connecting to Power Supply ................... 29 2.4 NUC-RPU Overviews ....................30 2.5 NUC-RPU Jumper & Connector list ................ 31 2.6 NCM-RPU Jumpers & Connectors settings ............32 2.6.1 M.2 Key B power select (JPWR_SEL1) ................32 2.6.2... - Page 15 Quick Reference Guide 3.5 Installing Stand Mounting (NUC-RPU) ..............44 3.6 System Mounting ....................45 4. Drivers Installation....................... 46 4.1 Install Chipset Driver ....................47 4.2 Install VGA Driver ....................48 4.3 Install Ethernet Driver ....................49 4.4 Install ME Driver ...................... 50 4.5 Install Serial IO Driver .....................
- Page 16 Discard Changes and Reset ..................... 83 5.6.6.3 Restore Defaults ....................... 84 5.6.6.4 Launch EFI Shell from filesystem device ................. 84 5.6.7 MEBx ........................... 84 6. Maintenance & Troubleshooting................. 85 7. Product Application ..................... 90 8. Operating the Device ....................91 16 NUC-RPU Quick Reference Guide...
-
Page 17: Getting Started
Before installation, please ensure all the items listed in the following table are included in the package. Item Description Q’ty NUC-RPU Adapter Table Stand, VESA, DIN Rail Kit Screw Kit (M.2, Mount kit) Rubber Foot NUC-RPU Quick Reference Guide 17... - Page 18 Step 3: Carefully cut the tape sealing the box. Only cut deep enough to break the tape. Step 4: Open the inside box. Step 5: Lift the panel PC out of the boxes. Step 6: Remove the peripheral parts box from the main box. 18 NUC-RPU Quick Reference Guide...
-
Page 19: System Specifications
1-M.2 Key-M 2280 NVMe (PCIe Gen4x4) Size, Signal) 1-M.2 Key-B 2242 SSD (SATA Gen3) Edge I/O (Front) USB Port 2-USB 2.0 COM Port 2-RS-232/422/485 (Control by BIOS setting) 1-Mic-In Audio 1-Line-Out Power Button 1-PWR BTN with LED NUC-RPU Quick Reference Guide 19... - Page 20 1-2P 1.25mm wafer reserved for the wired RTC battery Clear CMOS 1-3P 2.0mm header eSPI 1-2-6P 1.25mm header EC Debug 1-3P 2.0mm header Front Panel 1-2x5P 2.0mm header BIOS SPI 1-2x4P 2.0mm header DC-Input 1-6P 2.54mm wafer Display 20 NUC-RPU Quick Reference Guide...
- Page 21 Single power ATX support S0, S3, S4, S5 Power Mode AT/ATX (ATX is default setting) Adapter AC to DC adapter Mechanical & Environment Operating 0°C ~ 50°C (32°F ~ 122°F) with 0.5m/s air flow Temp. Storage Temp. -30~70C° (-22°F ~ 158°F) NUC-RPU Quick Reference Guide 21...
- Page 22 5 Test Axis : +/- X, +/-Y, +/-Z axis 6 operation mode 7 Reference IEC 60068-2-27 testing procedures Test Eb : SSD Shock Test Package drop test Drop Test Reference ISTA 2A, Method : IEC-60068-2-32 Test:Ed Test Ea : Drop Test 22 NUC-RPU Quick Reference Guide...
- Page 23 2 Test high : 96.5cm 3 Package weight : 5Kg 4 Test drawing IP Rating IP40 Mounting Kit Table Stand/Din Rail/VESA Kensington Kensington Lock Lock Software Support Win10, Win11, Linux Information Note: Specifications are subject to change without notice. NUC-RPU Quick Reference Guide 23...
-
Page 24: System Overview
USB 3.2 Gen1 USB 3.2 Gen1 connector x 2 USB 3.2 Gen2 USB 3.2 Gen2 connector x 4 *Note 1: Do not unplug the adapter and Jack arbitrarily after booting. It will cause system abnormalities. 24 NUC-RPU Quick Reference Guide... -
Page 25: System Dimensions
Quick Reference Guide 1.5 System Dimensions (Unit: mm) NUC-RPU Quick Reference Guide 25... -
Page 26: Operating Principle
- The power ON/OFF LED will turn blue to indicate power is on. Note - Check with the Icon behavior for power status. *Note: Power LED. S0: On S3: Blinking S4/S5: Off BIOS P.O.S.T: Blinking. 26 NUC-RPU Quick Reference Guide... -
Page 27: Hardware Configuration
Quick Reference Guide 2. Hardware Configuration For advanced information, please refer to: 1- NUC-RPU included in this manual. Note: If you need more information, please visit our website: www.avalue.com NUC-RPU Quick Reference Guide 27... -
Page 28: Nuc-Rpu Connector Mapping
In RS-232 Mode Signal PIN PIN Signal NDCD# NDSR# NRXD NRTS# NTXD NCTS# NDTR# NRI# In RS-422 Mode Signal PIN PIN Signal TxD1- TxD1+ RxD1+ RxD1- In RS-485 Mode Signal PIN PIN Signal DATA1- DATA1+ 28 NUC-RPU Quick Reference Guide... -
Page 29: Powering On The System
ACC On signal. Power 2 connector is a 6-pin terminal that can directly connect to a power adapter. The supported power input voltages are: ⚫ Power 1 (DIN connector)): 12 V ⚫ Power 2 (terminal block)): 12 V Power Input Connector Power Button NUC-RPU Quick Reference Guide 29... -
Page 30: Nuc-Rpu Overviews
NUC-RPU 2.4 NUC-RPU Overviews 30 NUC-RPU Quick Reference Guide... -
Page 31: Nuc-Rpu Jumper & Connector List
Quick Reference Guide 2.5 NUC-RPU Jumper & Connector list Jumpers Label Function Note JPWR_SEL1 M.2 Key B power select 3 x 1 header, pitch 2.00mm JAT1 AT/ATX Input power select 3 x 1 header, pitch 2.00mm JRTC1 Clear CMOS 3 x 1 header, pitch 2.00mm... -
Page 32: Ncm-Rpu Jumpers & Connectors Settings
NUC-RPU 2.6 NCM-RPU Jumpers & Connectors settings 2.6.1 M.2 Key B power select (JPWR_SEL1) 3.3V* 3.8V * Default 2.6.2 Clear CMOS (JRTC1) Normal* Clear CMOS * Default 32 NUC-RPU Quick Reference Guide... -
Page 33: At/Atx Input Power Select (Jat1)
Quick Reference Guide 2.6.3 AT/ATX Input power select (JAT1) ATX* * Default 2.6.4 ESPI connector (JESPI1) Signal PIN PIN Signal ESPI_IO0 +3.3VSB ESPI_IO1 PLT_RST_BUF# ESPI_IO2 ESPI_CS0# ESPI_IO3 ESPI_CLK ESPI_RST NUC-RPU Quick Reference Guide 33... -
Page 34: Battery Connector (Jbat1)
NUC-RPU 2.6.5 Battery connector (JBAT1) Signal +RTCBAT 2.6.6 Front Panel connector (JFP1) Signal PIN PIN Signal FP_HDD_LED+ FP_PWR_LED+ HDD_LED# PWR_LED# RSTBTN# PWR_BTN_IN# 34 NUC-RPU Quick Reference Guide... -
Page 35: Usb2.0 Connector (Jusb1)
Quick Reference Guide 2.6.7 USB2.0 connector (JUSB1) Signal PIN PIN Signal +V5A_USB_INT +V5A_USB_INT USB_R_DN7 USB_R_DN8 USB_R_DP7 USB_R_DP8 2.6.8 SPI connector (JSPI1) Signal PIN PIN Signal +V3.3A_SPI SPI_CS#0 SPI_CLK SPI_MISO SPI_MOSI SPI_HOLD# SPI_WP# NUC-RPU Quick Reference Guide 35... -
Page 36: General Purpose I/O Connector (Jdio1)
NUC-RPU 2.6.9 General purpose I/O connector (JDIO1) Signal PIN PIN Signal DIO_GP20 DIO_GP10 DIO_GP21 DIO_GP11 DIO_GP22 DIO_GP12 DIO_GP23 DIO_GP13 SMB_SCL_S0 SMB_SDA_S0 +V5S_DIO 2.6.10 Power connector (DCIN2) Signal +V12A_VIN +V12A_VIN +V12A_VIN 36 NUC-RPU Quick Reference Guide... -
Page 37: Sata Power Connector (Jsatapwr1)
Quick Reference Guide 2.6.11 SATA Power connector (JSATAPWR1) Signal 2.6.12 EC connector (JEC1) Signal EC_SMCLK_DEBUG EC_SMDAT_DEBUG NUC-RPU Quick Reference Guide 37... -
Page 38: Installation
NUC-RPU 3. Installation 38 NUC-RPU Quick Reference Guide... - Page 39 ⚫ Anti-static Discharge: If a user open the rear panel of the flat bezel panel PC, to configure the jumpers or plug in added peripheral devices, ground themselves first and wear an anti-static wristband. NUC-RPU Quick Reference Guide 39...
-
Page 40: Installing Memory Card (Nuc-Rpu)
NUC-RPU 3.1 Installing Memory card (NUC-RPU) Step1. Remove 4 screws from the bottom of your system and take it off. Step2. Slide the DDR5 SODIMM into the memory socket and press it down until properly seated. Step3. Paste the Thermal Pad to complete installation... -
Page 41: Installing M.2 Key-M Card (Nuc-Rpu)
Quick Reference Guide 3.2 Installing M.2 Key-M card (NUC-RPU) Step1. Insert M.2 Key-M card into designated locations and fasten with the screw to complete installation. Step2. Paste the Thermal Pad to complete installation NUC-RPU Quick Reference Guide 41... -
Page 42: Installing Vesa Mounting (Nuc-Rpu)
NUC-RPU 3.3 Installing VESA Mounting (NUC-RPU) Step1. Insert and fasten two M3*L11.1 screws on the bottom. Step2. Fix with four M4*6mm screws on the monitor (or wall). 42 NUC-RPU Quick Reference Guide... -
Page 43: Installing Din Rail Mounting (Nuc-Rpu)
Quick Reference Guide Step3. Slide the system onto the VESA mount bracket. 3.4 Installing Din Rail Mounting (NUC-RPU) Step1. Insert Din Rail into designated locations and fasten with the two M3*4 screws to complete installation. NUC-RPU Quick Reference Guide 43... -
Page 44: Installing Stand Mounting (Nuc-Rpu)
NUC-RPU 3.5 Installing Stand Mounting (NUC-RPU) Step1. Fix with four 6#32*5 screws on the system. 44 NUC-RPU Quick Reference Guide... -
Page 45: System Mounting
Keep the wires separated according to the interface. Wires that share similar electrical characteristics must be bundled together. ⚫ Do not bundle input wiring with output wiring. Keep them separate. ⚫ When necessary, it is strongly advised that you label wiring to all devices in the system. NUC-RPU Quick Reference Guide 45... -
Page 46: Drivers Installation
HID touch digitizer built-in driver in Windows 7 or later. Note: Installation procedures and screen shots in this section are for your reference and may not be exactly the same as shown on your screen. 46 NUC-RPU Quick Reference Guide... -
Page 47: Install Chipset Driver
Windows 10 operation system. If the warning message appears while the installation process, click Continue to go on. Step 3. Click Install. Step1. Click Next. Step 4. Click Finish to complete setup. Step 2. Click Accept. NUC-RPU Quick Reference Guide 47... -
Page 48: Install Vga Driver
Note: The installation procedures and screen shots in this section are based on Windows 10 operation system. Step 3. Click Start. Step 1. Click Begin installation. Step 4. Click Finish to complete setup. Step 2. Click I agree. 48 NUC-RPU Quick Reference Guide... -
Page 49: Install Ethernet Driver
All drivers can be found on the Avalue Official Website: www.avalue.com. Note: The installation procedures and screen shots in this section are based on Windows 10 operation system. Step 1. Click OK to continue installation. Step 2. Setup completed. NUC-RPU Quick Reference Guide 49... -
Page 50: Install Me Driver
Note: The installation procedures and screen shots in this section are based on Windows 10 operation system. Step 3. Click Next. Step 1. Click Next to continue installation. Step 4. Click Finish to complete setup. Step 2. Click Next. 50 NUC-RPU Quick Reference Guide... -
Page 51: Install Serial Io Driver
Windows 10 operation system. Step 3. Click Next. Step 1. Click Next to continue installation. Step 4. Click Next. Step 2. Click Next. Step 5. Click Finish to complete setup. NUC-RPU Quick Reference Guide 51... -
Page 52: Bios Setup
NUC-RPU 5.BIOS Setup 52 NUC-RPU Quick Reference Guide... -
Page 53: Introduction
If you do not press the keys at the correct time and the system does not boot, an error message will be displayed and you will again be asked to. Press F1 to Continue, DEL to enter SETUP NUC-RPU Quick Reference Guide 53... -
Page 54: Using Setup
Note: Some of the navigation keys differ from one screen to another. • To Display a Sub Menu Use the arrow keys to move the cursor to the sub menu you want. Then press <Enter>. A “➢” pointer marks all sub menus. 54 NUC-RPU Quick Reference Guide... -
Page 55: Getting Help
BIOS Vendor and your systems manufacturer to provide the absolute maximum performance and reliability. Even a seemingly small change to the chipset setup has the potential for causing you to use the override. NUC-RPU Quick Reference Guide 55... -
Page 56: Bios Setup
<Enter> to accept and enter the sub-menu. 5.6.1 Main Menu This section allows you to record some basic hardware configurations in your computer and set the system clock. 56 NUC-RPU Quick Reference Guide... -
Page 57: System Language
Visit the Avalue website (www.avalue.com) to download the latest product and BIOS information. 5.6.2 Advanced Menu This section allows you to configure your CPU and other system devices for basic operation through the following sub-menus. NUC-RPU Quick Reference Guide 57... -
Page 58: Connectivity Configuration
Discrete solution is discovered it will be Disable Integrated enabled by default. Otherwise Integrated solution (CNVi) CNVi Mode Auto Detection[Default] will be enabled; [Disable Integrated] disables Integrated Solution. NOTE: When CNVi is present, the GPIO pins that are used for radio. 58 NUC-RPU Quick Reference Guide... -
Page 59: Cpu Configuration
When both are {0,0}, Pcode will enable all cores. All[Default] Number of E-cores to enable in each processor package. Note: Number of Cores and E-cores are Active Efficient-cores looked at together. When both are {0,0}, Pcode will enable all cores. NUC-RPU Quick Reference Guide 59... -
Page 60: Efficient-Core Information
NUC-RPU 5.6.2.2.1 Efficient-core Information 5.6.2.2.2 Performance-core Information 60 NUC-RPU Quick Reference Guide... -
Page 61: Power & Performance
Allows more than two frequency ranges to be Intel® SpeedStep™ Disabled supported. Eanble/Disable Intel® Speed Shift Technology Intel® Speed Shift Enabled[Default], support. Enabling will expose the CPPC v2 interface to Technology Disabled allow for hardware controlled P-states. NUC-RPU Quick Reference Guide 61... -
Page 62: Pch-Fw Configuration
Enable/Disable C1E. When enabled, CPU will switch Enhanced C-States Disabled[Default] to minimum speed when all cores enter C-State. 5.6.2.4 PCH-FW Configuration Item Option Description Disabled When Disabled ME will be put into ME Temporarily ME State Enabled[Default], Disabled Mode. 62 NUC-RPU Quick Reference Guide... -
Page 63: Firmware Update Configuration
Description Selects TPM device: PTT or dTPM. PTT-Enables PTT in dTPM[Default], SkuMgr dTPM1.2 – Disables PTT in SkuMgr Warning! TPM Device Selection PTT/dTPM will be disabled and all data saved on it will be lost. NUC-RPU Quick Reference Guide 63... -
Page 64: Trusted Computing
INT1A interface will not be available. 5.6.2.6 APCI Settings Item Options Description Enables or Disables System ability to Hibernate Disabled Enable Hibernation (OS/S4 Sleep State). This option may not be Enabled[Default], effective with some OS. 64 NUC-RPU Quick Reference Guide... -
Page 65: Super Io Configuration
5.6.2.7.1 ~ 5.6.2.7.2 for more information. Item Description Serial Port 1 Configuration Set Parameters of Serial Port 1 (COMA). Serial Port 2 Configuration Set Parameters of Serial Port 2 (COMB). 5.6.2.7.1 Serial Port 1 Configuration NUC-RPU Quick Reference Guide 65... -
Page 66: Serial Port 2 Configuration
Low[Default] Low: RS232/422/485 = 250Kbps High: UART Slew Rate High RS422/485 = 20Mbps. Non INT+EXT R[Default] EXT R Adjust the Serial Port with internal or external UART 422/485 Termination INT R termination resistors. INT+EXT R 66 NUC-RPU Quick Reference Guide... -
Page 67: Ec 5782 Hw Monitor
Enable or disable System wake on alarm event. Select Disabled[Default], Fixed Time, system will wake on the hr::min::sec specified. Wake system from S5 Fixed Time Select Dynamic Time, System will wake on the current time Dynamic Time + Increase minute(s). NUC-RPU Quick Reference Guide 67... -
Page 68: Serial Port Console Redirection
Console Redirection EMS Console Redirection Enable or Disable. Enabled 5.6.2.10.1 Legacy Console Redirection Settings Item Option Description Select a COM port to display redirection of Redirection COM Port COM0[Default] Legacy OS and Legacy OPROM Messages. 68 NUC-RPU Quick Reference Guide... -
Page 69: Usb Configuration
Auto[Default] Floppy enumerates devices according to their media Mass Storage Devices Forced FDD format. Optical drives are emulated as ‘CDROM’, drives with no media will be Hard Disk CD-ROM emulated according to a drive type. NUC-RPU Quick Reference Guide 69... -
Page 70: Network Stack Configuration
NUC-RPU 5.6.2.12 Network Stack Configuration Item Options Description Enabled Network Stack Enable/Disable UEFI Network Stack. Disabled[Default] 5.6.2.13 NVMe Configuration 70 NUC-RPU Quick Reference Guide... -
Page 71: Chipset
Quick Reference Guide 5.6.3 Chipset 5.6.3.1 System Agent (SA) Configuration Item Option Description Enabled VT-d VT-d capability. Disabled[Default] NUC-RPU Quick Reference Guide 71... -
Page 72: Memory Configuration
NUC-RPU 5.6.3.1.1 Memory Configuration 5.6.3.1.2 Graphics Configuration Item Option Description Auto Select IGFX Graphic device should be Primary Primary Display IGFX[Default] Display. 72 NUC-RPU Quick Reference Guide... -
Page 73: Pch-Io Configuration
Quick Reference Guide 5.6.3.2 PCH-IO Configuration Item Option Description Enabled[Default] PCH LAN Controller Enable/Disable onboard NIC. Disabled 5.6.3.2.1 PCI Express Configuration NUC-RPU Quick Reference Guide 73... -
Page 74: Pci Express Root Port 5(M.2 Keye)
DISABLE – Disables ASPM. Auto Disabled[Default] L1 Substates PCI Express L1 Substates settings. L1.1 L1.1 & L1.2 Disabled[Default], L1 Low PCI Express L1 Substates Enable/Disable. Enabled Auto[Default] Gen1 PCIe Speed Configure PCIe Speed. Gen2 Gen3 74 NUC-RPU Quick Reference Guide... -
Page 75: Pci Express Root Port 6(Usb Hub)
DISABLE – Disables ASPM. Auto Disabled[Default] L1 Substates L1.1 PCI Express L1 Substates settings. L1.1 & L1.2 Disabled[Default], PCI Express L1 Low Substates L1 Low Enabled Enable/Disable. Auto[Default] Gen1 PCIe Speed Configure PCIe Speed. Gen2 Gen3 NUC-RPU Quick Reference Guide 75... -
Page 76: Pci Express Root Port 8(Lan2-I225/I226)
L1 Substates L1.1 PCI Express L1 Substates settings. L1.1 & L1.2 Disabled[Default], PCI Express L1 Low Substates L1 Low Enabled Enable/Disable. Disabled[Default], Enable/Disable Precision Time Enabled Measurement. Auto[Default] Gen1 PCIe Speed Configure PCIe Speed. Gen2 Gen3 76 NUC-RPU Quick Reference Guide... -
Page 77: Pci Express Root Port 12(M.2 Keyb)
DISABLE – Disables ASPM. Auto Disabled[Default] L1 Substates L1.1 PCI Express L1 Substates settings. L1.1 & L1.2 Disabled[Default], PCI Express L1 Low Substates L1 Low Enabled Enable/Disable. Auto[Default] Gen1 PCIe Speed Configure PCIe Speed. Gen2 Gen3 NUC-RPU Quick Reference Guide 77... -
Page 78: Sata Configuration
State Drive or Hard Disk Drive. Enabled[Default] Port 1 Enable or Disable SATA Port. Disabled Hard Disk Drive Identify the SATA port is connected to Solid SATA Device Type Solid State Drive[Default] State Drive or Hard Disk Drive. 78 NUC-RPU Quick Reference Guide... -
Page 79: Hd Audio Configuration
Enabled = HDA will be Enabled[Default] unconditionally enabled. 5.6.3.3 Board & Panel Configuration Item Option Description Disabled[Default] ErP Function ErP Function (Deep S5). Enabled PWR-On After PWR-Fail Off[Default] AC loss resume. NUC-RPU Quick Reference Guide 79... -
Page 80: Show Dmi Info
2 min 10 min 30 min Disabled Enable/Disabled USB Standby Power USB Standby Power Enabled[Default] during S3/S4/S5. Disabled[Default] Enabling will set M.2 KeyB Pin38(DEVSLP) M.2 Key-B P38 Setting Enabled as High. 5.6.3.3.1 SHOW DMI INFO 80 NUC-RPU Quick Reference Guide... -
Page 81: Security
Quick Reference Guide 5.6.4 Security ⚫ Administrator Password Set setup Administrator Password ⚫ User Password Set User Password 5.6.4.1 Secure Boot NUC-RPU Quick Reference Guide 81... -
Page 82: Boot
Enabled boot option. Has no effect for BBS boot optios. Disabled[Default] Quiet Boot Enables or disables Quiet Boot option Enabled Boot Option #1/2 Set the system boot order. 82 NUC-RPU Quick Reference Guide... -
Page 83: Save And Exit
Reset the system after saving the changes. 5.6.6.2 Discard Changes and Reset Any changes made to BIOS settings during this session of the BIOS setup program are discarded. The setup program then exits and reboots the controller. NUC-RPU Quick Reference Guide 83... -
Page 84: Restore Defaults
BIOS setting. 5.6.6.4 Launch EFI Shell from filesystem device Attempts to Launch EFI Shell application (Shellx64.efi) from one of the available filesystem devices. 5.6.7 MEBx ⚫ Intel® ME Password MEBx Login 84 NUC-RPU Quick Reference Guide... -
Page 85: Maintenance & Troubleshooting
System Maintenance Introduction If the components of the product fail they must be replaced. Please contact the system reseller or vendor to purchase the replacement parts. Please follow the safety precautions outlined in the sections that follow NUC-RPU Quick Reference Guide 85... -
Page 86: General Safety Precautions
Drop the device against a hard surface. ⚫ Strike or exert excessive force onto the LCD panel. ⚫ Touch any of the LCD panels with a sharp object. ⚫ In a site where the ambient temperature exceeds the rated temperature. 86 NUC-RPU Quick Reference Guide... -
Page 87: Anti - Static Precautions
This reduces the possibility of ESD damage. ⚫ Only handle the edges of the electrical component. When handling the electrical component, hold the electrical component by its edges. Please ensure the following safety precautions are adhered to at all times. NUC-RPU Quick Reference Guide 87... -
Page 88: Maintenance And Cleaning
Never drop any objects or liquids through the openings of the device. ⚫ Be cautious of any possible allergic reactions to solvents or chemicals used when cleaning the device. ⚫ Avoid eating, drinking and smoking within vicinity of the device. 88 NUC-RPU Quick Reference Guide... -
Page 89: Cleaning Tools
Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are excellent tools for wiping hard to reach areas. ⚫ Foam swabs: Whenever possible, it is best to use lint free swabs such as foam swabs for cleaning. NUC-RPU Quick Reference Guide 89... -
Page 90: Product Application
Avalue technical support team, or Avalue customer service representatives for further information. Feel free to inquire about this supplementary resource to enhance your understanding of the Watchdog Timer and Digital I/O (DIO) Application for optimal utilization of your Panel 90 NUC-RPU Quick Reference Guide... -
Page 91: Operating The Device
Avalue technical support team, or Avalue customer service representatives. These professionals can provide tailored guidance and assistance to address any unique needs related to Multi-Touch mode adjustments. NUC-RPU Quick Reference Guide 91...
Need help?
Do you have a question about the NUC-RPU and is the answer not in the manual?
Questions and answers