Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for IKA CG-2053
Summary of Contents for IKA CG-2053
- Page 1 MINISTAR control...
- Page 2 ENGLISH...
- Page 3 2014/35/EU, 2006/42/EC, 2014/30/EU, 2014/53/EU and 2011/65/EU and conforms with the standards or standardized documents: EN 61010-1, EN 61010-1-2-051, EN 61326-1, EN 60529 and EN ISO 12100. A copy of the complete EU Declaration of Conformity or further declarations of conformity can be requested at sales@ika.com.
- Page 4 › Assembling the mixing vessel to the stand ....26 /// PERMITTED IKA STIRRER TOOLS › An overview ........39 /// COMMISSIONING ›...
- Page 5 Device setup /// MINISTAR control /// What you should watch out for Operator panel and display Chuck Extension arm Temperature sensor socket Power socket Attention! ( USB interface Stirring shaft cap...
- Page 6 Safety instructions /// Explication of warning symbols /// General information › Read the operating instructions in full before starting up and follow the safety instructions. › Keep the operating instructions in a place where it can be accessed by everyone. ›...
- Page 7 Danger! ( Danger! ( Users must make sure that the OFF switch of the IKA device can be accessed Do not operate the device in explosive atmospheres, with hazardous immediately, directly and without risk at any time. If installation or positioning substances or under water.
- Page 8 /// Accessories › Imbalance of the output shaft, the chuck and in particular the stirring › Protect the device and accessories from bumping and impacting. tools can lead to uncontrolled resonant vibrational behavior of the device › Check the device and accessories beforehand for damage each time and the whole assembly.
- Page 9 Correct use Unpacking /// Basics /// Scope of Delivery › Unpack the device carefully. › For mixing / stirring liquids from low to medium viscosities › Any damage should be notified immediately to the shipping agent (post with various stirring tools. office, railway network or logistics company).
- Page 10 The clamping chuck and output shaft permit clamping IKA recommend stirrer Fluctuations in mains voltage within the permitted tolerance range have no tools (see section “Permitted IKA Stirrer tools“). The output shaft is designed effect on the quality of regulation and constancy of speed.
- Page 11 Operator panel and display /// Operation Display MINISTAR 20 control Device switches on / enters standby Standby key (no disconnection from the power supply network). Lock key Lock / unlock keys and knob. Activate / deactivate the internal vibration sensor. Vibration monitoring Set individual levels (I/II/III).
- Page 12 /// Explanation of symbols on the display The symbols appear on the screen change depending on the status Display and settings of the device. The following screen shows the most This symbol indicates all function keys except for the standby key (A) are locked. significant symbols.
- Page 13 Assembly /// Assembling the extension arm /// Assembling the overhead stirrer to the overhead stirrer to the stand Cross sleeve Screw bolt Extension arm Stirrer Stand Extension arm Check that the stirrer is held in position firmly prior to each use and also at Hexagonal socket screw regular intervals.
- Page 14 Commissioning /// Assembling the stirring shaft protector /// Switching on Secure the device to a stable stand with a cross sleeve. Stirrer The stirring vessel must always be securely fixed for safety reasons. You must also ensure that the mounting device (stand) is set up in such a way that it is not liable to topple and does not start to move during the stirring procedure.
- Page 15 Setting speed Locking the keys and knob › Ensure the speed set is suitable for the test medium selected. If in doubt, By touching the lock key (B) about 2 seconds, you can lock the control elements set the speed to the lowest speed (counterclockwise direction) by rotating of the device.
- Page 16 /// Calibration Notice! ( ) › Pressing the control knob (G) starts the torque calibration. Stirring tool must be removed from the chuck! In calibration mode the chuck rotates up to max. speed. The setting functions can be exited at any time by toucing the standby key (A).
- Page 17 Install the driver individual items of laboratory control equipment, rev. 1.1). by running the setup file. Then connect the IKA device through the USB data The NAMUR commands and the additional specific IKA co mmands serve only cable to the PC. The data communication is via a virtual COM port.
- Page 18 IN_NAME Read device name For cleaning disconnect the main plug! IN_PV_3 Read PT1000 value Use only cleaning agents which have been approved by IKA to clean IKA devices: IN_PV_4 Read current speed value water containing tenside / isopropyl alcohol. IN_PV_5...
- Page 19 Error codes /// Troubleshooting correctly Err. 04 If an error occurs, the fault is shown by an error code on the screen. Proceed as follows in such cases: Cause › motor blockage or overload › Disconnect the device from the power supply. Effect ›...
- Page 20 Permitted IKA stirrer tools /// Regulations /// An overview In accordance with IKA warranty conditions, the warranty period is 24 Propeller stirrer months. For claims under the warranty please contact your local dealer. › R 1342 max. speed (rpm) ≤ 2,000 You may also send the machine direct to our factory, enclosing the delivery ›...
- Page 21 Technical data /// MINISTAR control in detail Technical data MINISTAR control Max. output power at stirring shaft 42 W MINISTAR Protection class acc. to EN 60529 IP 54 20 control | 40 control | 80 control Speed range under Contamination level 0 / 50 –...
- Page 22 Phone: +66 2059 4690 Phone: +90 216 394 43 43 Phone: +84 28 38202142 eMail: sales.lab-thailand@ika.com eMail: sales.turkey@ika.com eMail: sales.lab-vietnam@ika.com Discover and order the fascinating products of IKA online: www.ika.com IKAworldwide IKAworldwide /// #lookattheblue @IKAworldwide Technical specifications may be changed without prior notice.
Need help?
Do you have a question about the CG-2053 and is the answer not in the manual?
Questions and answers