Table of Contents
Advertisement
Quick Links
Ei25
LED Electric Fire Range
with Thermostatic Remote Control
Instructions for Use, Installation & Servicing
For use in AU & NZ (Australia & New Zealand)
PARTS OF THE OUTER CASING OF THIS APPLIANCE ARE CONSIDERED BY THE MANUFACTURER TO BE A WORKING
SURFACE WHICH BECOMES HOT WHEN THE HEATER IS IN OPERATION AND WILL RESULT IN SERIOUS INJURY AND
BURNS IF TOUCHED. IT IS THEREFORE RECOMMENDED THAT A FIREGUARD IS USED IN THE PRESENCE OF YOUNG
Please read these instructions carefully before installation and keep them in a safe place.
THIS PRODUCT IS ONLY SUITABLE FOR WELL INSULATED SPACES AND OCCASIONAL USE.
CHILDREN, THE ELDERLY OR INFIRM.
THE HEATER OUTLET GRILLE BECOMES VERY HOT WHILST IN OPERATION.
DO NOT COVER THE OUTLET GRILLE OR ANY PART OF THE APPLIANCE.
For use with 230V 50Hz electricity supply only.
They will be needed when maintenance or servicing is required.
THIS APPLIANCE MUST BE EARTHED
IMPORTANT
PR3295AZ.1.08.2024
Advertisement
Table of Contents
Related Manuals for Regency Fireplace Products Ei25
Summary of Contents for Regency Fireplace Products Ei25
- Page 1 Ei25 LED Electric Fire Range with Thermostatic Remote Control Instructions for Use, Installation & Servicing For use in AU & NZ (Australia & New Zealand) IMPORTANT PARTS OF THE OUTER CASING OF THIS APPLIANCE ARE CONSIDERED BY THE MANUFACTURER TO BE A WORKING SURFACE WHICH BECOMES HOT WHEN THE HEATER IS IN OPERATION AND WILL RESULT IN SERIOUS INJURY AND BURNS IF TOUCHED.
-
Page 2: Table Of Contents
CONTENTS Ei25 - LED Electric Fire Range Covering the following models: Ei25 210-430 User Instructions ............3 WARRANTY This system carries a 2 years parts-labour warranty. Installation Instructions ..........9 Please note that all warranties are effective from the date of purchase. -
Page 3: User Instructions
USER INSTRUCTIONS This appliance can be used by children aged from 8 years and IMPORTANT INFORMATION AND above and persons with reduced physical, sensory or mental HEALTH AND SAFETY capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. -
Page 4: Manual Control Panel
OPERATING INSTRUCTIONS WARNING! Do not operate the appliance if it is REMOTE CONTROL damaged or has malfunctioned. If you suspect the appliance is damaged or has malfunctioned call a suitably quality person to inspect the appliance, The remote control should be left on a flat surface in the room and replace any part of the electrical system if where the appliance is installed and away from any direct flow necessary, before reuse. - Page 5 FUEL BED COLOUR ADJUSTMENT OPERATING THE APPLIANCE - ADVANCED OPERATION Press to enter the fuel bed light adjustment screen. There are 15 fuel bed colour options, including off. Temperature Sensor Convection There are 5 levels of brightness. Display Power Flame Fuel Bed Heating Timer...
- Page 6 Ensure that the handset batteries are new and inserted correctly. OPERATING THE APPLIANCE - TROUBLESHOOTING Dispose of old batteries at an appropriate recycling facility. Battery replacement is recommended after 1 year. BATTERY The Remote requires two 1.5V alkaline AAA batteries. The battery power level is indicated at the top right of the remote Ensure the correct polarity.
-
Page 7: Maintenance
MAINTENANCE ENSURE THE APPLIANCE IS TURNED OFF BEFORE CLEANING. GLASS CLEANING Wipe the glass viewing panel with a damp cloth and buff with a lint free duster. Caution: Do not use abrasive cleaners on the glass panel. Do not spray liquids directly onto any surface of the unit. CLEANING THE FUEL EFFECT Remove and wash the fuel effect to remove any dust particles. - Page 8 CLEANING AIR INLETS Clean the air inlet and outlet grilles regularly with a soft cloth or the nozzle of a vacuum cleaner. Dust build-up can inhibit efficient performance of the fan and lead to the safety cut-out operating. Keep the area around the appliance clean and free of fluff, dust or pet hair.
-
Page 9: Fitting The Appliance
TEST THE APPLIANCE BEFORE INSTALLATION. FITTING THE APPLIANCE LOCATING THE Ei25 Your new Ei25 may be installed virtually anywhere in your home. However, when choosing a location ensure that the general instructions are followed. For best results, install out of direct sunlight. -
Page 10: Servicing Requirements
SERVICING REQUIREMENTS DURING SERVICING OF THIS APPLIANCE IT MAY BE NECESSARY TO CUT CABLE TIES IN ORDER TO ACCESS AND REMOVE SOME OF THE PARTS. THESE MUST BE REPLACED WHEN REASSEMBLING THE APPLIANCE. THIS APPLIANCE MUST ONLY BE SERVICED BY A SUITABLY QUALIFIED PERSON. -
Page 11: Technical Specifications
TECHNICAL SPECIFICATION Ei25 210-430 DIMENSIONS (mm) Ei25 10.5... -
Page 12: Installation
INSTALLATION 653mm 450mm 320mm Ei25 CONTROL SYSTEM TECHNICAL DATA MAIN CONTROL BOARD REMOTE RECEIVER BOARD REMOTE CONTROL Hardware RC01-086A V0 RF290I V1.2 RC290F V1.1 Software RC01-086A01 V0 RCS19-V01.06 Frequency FSK 433.92MHz Maximum Transmit Power 10mW Maximum power consumption: A 230-240VAC 10 Amp 50Hz supply is required... -
Page 13: Packing Checklist
PACKING CHECKLIST x2 (AAA) x4 (ST4x40) x10 (ST4x8) -
Page 14: Accessing The Fuel Bed
ACCESSING THE FUEL BED... -
Page 15: Levelling Legs
LEVELLING LEGS NOTE: The levelling of the appliance must be done prior to sliding appliance into final position. The leveling bolts which are supplied must be installed with bolts from below as shown. Rest appliance on its back and secure 4 bolts as shown above. - Page 16 INSTALLATION...
-
Page 17: Log Layout
LOG SET - LOG LAYOUT Glass Embers Amber Crystals Ei25... - Page 18 Place glass embers (H) evenly with white sides facing up. Apply tape to logs at white dot positions Adhesive Tape E x3 Adhesive Tape x1 F x2...
- Page 19 COMPLETION OF ASSEMBLY...
-
Page 20: Servicing Instructions
SERVICING PAIRING THE REMOTE ACCESSING THE FUEL BED SIGNAL CODE The below operations should be carried out before coding when changing to a new remote or the unit cannot be controlled by the remote: The reset button is located on the control panel located on the right-hand side of the appliance. - Page 21 REMOVAL OF THE FUEL BED Remove 4 rubber plugs using a small flat head screwdriver on grate (not shown) and then remove 4 screws ( 2 at back/2 at front) as shown below. x 13...
- Page 22 REPLACING THE FUEL BED LEDS...
- Page 23 REPLACING THE LED LIGHT BAR Carefully lower the LED Light Bar and disconnect the cable from the right hand side.
-
Page 24: Removing The Button Board
REMOVING THE BUTTON BOARD... - Page 25 INNER SCREEN REMOVING THE INNER SCREEN REAR GLASS...
- Page 26 REMOVING THE FLAME EFFECT REMOVING THE EFFECT SPINDLE x 11...
- Page 27 REPLACING THE FLAME EFFECT LEDS...
- Page 28 REMOVING THE EFFECT MOTOR REMOVING TOP BAFFLE...
-
Page 29: Removing The Pcb
REMOVING THE PCB Top Baffle flaps BAFFLE Top Baffle Rear of Rear Bracket flaps appliance... -
Page 30: Removing The Receiver
REMOVING THE RECEIVER... -
Page 31: Replacing The Heater
REPLACING THE HEATER... -
Page 32: Wiring Diagram
WIRING DIAGRAM LED Board RC07-283A Fan Motor Heater Receiver Board WIFI Board RC02-084A Button Board RC02-041A WIFI Receiver Board RC05-015A Switch AC250V 16A Flame Motor Power Cable LED Board RC07-288A (Total 8 pcs) LED board RC07-191D (Total 1 pcs) COLOUR CODES BLUE YELLOW WHITE... -
Page 33: Spare Parts List
SPARE PARTS Ei25 Ei25 PART PART CODE PART PART CODE Log Set AAA Battery EL0062 CE2233 Glass Embers CE2235 Remote EL1163 Amber Crystals RC07-288A CE2234 RC07-289A Fuelbed LEDs EL1154 Receiver EL1153 RC07-290A EL1061 Inner Screen Flame Motor EL0632 PL0276 Rear Glass... -
Page 34: Information Requirement
INFORMATION REQUIREMENT FOR ELECTRIC LOCAL SPACE HEATERS Model Ei25 Nominal Heat Output P nom 2.0kW Minimum Heat Output P min 1.0kW Maximum Continuous Heat Output P max, c 2.0kW At Nominal Heat Output el max 10.0W At Minimum Heat Output el min 9.5W... -
Page 35: Limited Warranty
WARRANTY LIMITED WARRANTY This product comes with an extended Limited Warranty to the original purchaser of this appliance provided the product remains in the original place of installation. Some conditions apply (see below). The policy is not transferable, amendable or negotiable under any circumstances. After the original warranty coverage has expired, any repair and/or replacement parts purchased by the consumer through an accredited distributor or dealer will carry a ninety (90) day warranty (valid only with an original copy of the tax invoice). - Page 36 WARRANTY EXCLUSIONS This Limited Warranty does not extend to paint, rust or corrosion of any kind due to a lack of maintenance or improper venting, combustion air provision, corrosive chemicals (i.e. chlorine, salt, air, etc.), firebrick (rear, sides or bottom), door or glass gasket, or any other additional factory fitted gasket.
-
Page 37: Limitations Of Liability
WARRANTY LIMITATIONS OF LIABILITY 1. Exclusion of implied terms The customer may have the benefit of consumer guarantees under the Consumer Law. To the maximum extent permitted by law, all terms, conditions or warranties that would be implied into this Warranty or in connection with the supply of any goods or services by the supplier under law or statute or custom or international conventions are excluded. - Page 40 Fireplace Products Australia Pty Ltd 99 Colemans Road Dandenong South VIC, 3175 AUSTRALIA +613 9799 7277 www.regency-fire.com.au *PRPR3295AZ* PR3295AZ...
Need help?
Do you have a question about the Ei25 and is the answer not in the manual?
Questions and answers