Extron electronics CrossPoint DTP3 Series Setup Manual page 4

•
Reset button — Initiates four levels of matrix switcher reset. For different reset levels, press and hold the recessed
while the switcher is running or while powering up the switcher (see the DTP3 CrossPoint Series User Guide, at
for more details).
•
Reset LED — Indicates the level reset initiated on the matrix switcher.
Power inlet (see figure 2
R
Front Panel Features
1 2 3
9 10 11
1 2 3
9 10 11
Figure 5. DTP3 CrossPoint IPCP A Front Panel
Input buttons
A
Output buttons
B
USB Config port
C
Select Logo button
D
Enter Control button
E
NOTES:
•
Only the IPCP A model has the IPCP Status LEDs (
•
Many of the front panel buttons have multiple functions. For detailed information on the functions of the front panel buttons and
LEDs, go to the DTP3 CrossPoint Series User Guide online at www.extron.com.
Front Panel Connection
Configuration port — Connect to this USB-C port for remote control of the switcher.
C
NOTES:
•
The front panel USB-C is IP over USB with a hardcoded IP address,
•
A front panel Configuration port connection and a rear panel Remote port connection can both be active at the same time. If
commands are sent simultaneously to both, the command that reaches the processor first is handled first.
ShareLink Pro Connections (SL Models Only)
LAN ports — Use an Ethernet cable to connect a network switch, hub, router, or PC to these female RJ-45
A
ports.
NOTES:
•
If it has not been changed, the LAN A port default IP address is
•
If it has not been changed, the LAN B port default IP address is
•
Default Subnet mask for both LAN ports is
•
Default Gateway IP address for both LAN ports is
USB 5Gbps port — Use a USB Type A cable to connect 3.0 speed devices such as cameras to this USB 3.0
B
SuperSpeed port.
See the ShareLink Pro 1100 User Guide at
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
and Regulatory Compliance Guide
4
on page 2) — Connect a standard IEC power cord to a 100 VAC to 240 VAC, 50-60 Hz power source.
A A A
INPUTS
4 5 6 7 8
LOGO
12
SELECT
OUTPUTS
CONFIG
4 5 6 7 8
12
B B B C C C D D D
Preset Control button
F
View Control button
G
Escape Control button
H
Video I/O button
I
Audio I/O button
J
www.extron.com
on the Extron website.
© 2024 Extron — All rights reserved.
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
CONTROL
I/O
ENTER PRESET VIEW ESCAPE VIDEO AUDIO
INPUTS
DTP3
DTP
5 6 1
E E E F F F G G G H H H I I I J J J
) and the AMP Out Status LEDs (
M
203.0.113.22
192.168.253.249
192.168.254.249
255.255.255.0
.
.
0.0.0.0
to configure and operate the ShareLink Pro module.
www.extron.com
M M M
PoE+
COM
PWR
RTS
IR/S I/O RELAYS
CTS
2 1 1 2 1 2
Tx
IR
Rx
3 1 2 3 2 3 4 3 4
DTP REMOTE POWER AMP OUT
LIMITTER/ OUTPUT MODE
OUTPUTS DTP3 I/O
PROTECT
BRIDGED MONO
1 7 0 V
8Ω
2 8Ω/
1 0 0 V
4Ω
2 3 4 5 6 9 10 11 12
STEREO
DTP3 CROSSPOINT SERIES
SCALING PRESENTATION MATRIX SWITCHER
K K K L L L
DTP Remote Power Status LEDs
K
AMP Out Status LEDs
L
IPCP Status LEDs
M
).
L
, which cannot be changed.
.
.
Reset button
www.extron.com
B B B
A A A
Figure 6.
ShareLink Pro
Connections
Extron Safety
68-3058-50 Rev. A
09 24