insys icom MIRO Installation And User Manual

Hide thumbs Also See for MIRO:

Installation and user manual (56 pages)

Table Of Contents

Quick Links

Download this manual

MIRO / MIROdul

Installation and User Manual

Table of Contents

Need help?

Do you have a question about the MIRO and is the answer not in the manual?

Questions and answers

Summary of Contents for insys icom MIRO

Page 1 MIRO / MIROdul Installation and User Manual...
Page 3 Copyright © July 2024 INSYS icom GmbH Any duplication of this manual is prohibited. All rights on this documentation and the devices are with INSYS icom GmbH Regensburg. Trademarks and logos The use of a trademark or logo not shown below does not indicate that it is freely available for use.
Page 4: Table Of Contents
Content Preface ....................6 Defects Liability Terms ..................6 Applicability ......................6 Feedback ......................6 Marking of Warnings and Notes ................7 Meaning of the Symbols and the Formatting in this Manual ........ 8 Safety Instructions ................. 9 Usage According to the Regulations ..............9 Permissible Technical Limits................
Page 5 Contents Mounting ..................... 29 DIN rail mounting ....................30 8.1.1 DIN rail mounting with integrated adapter ..........30 8.1.2 DIN rail mounting with accessory adapter ..........32 Screw mounting ....................36 Connecting the power supply ................38 Commissioning ..................39 Operating Principle ................
Page 6: Preface
We are looking forward to any of your feed- back. Please send an e-mail to support@insys-icom.de. We’d like to know your applications. Please send us a few headwords that we know the applications you solve using products of INSYS icom.
Page 7: Marking Of Warnings And Notes
MIRO Preface Marking of Warnings and Notes Symbols and Key Words Danger! Risk of severe or fatal injury One of these symbols in conjunction with the key word Danger indicates an imminent danger. It will cause death or severe injuries if not avoided.
Page 8: Meaning Of The Symbols And The Formatting In This Manual
Preface MIRO Meaning of the Symbols and the Formatting in this Manual This section describes the definition, formatting and symbols used in this manual. The various symbols are meant to help you read and find the information relevant to you. The following text is structured like a typical operating instruction of this manual.
Page 9: Safety Instructions
MIRO Safety Instructions Safety Instructions The Safety Instructions section provides an overview about the safety instructions, which must be observed for the operation of the product. The product is constructed according to the currently valid state-of-the-art technol- ogy and reliable in operation. It has been checked and left the factory in flawless condition concerning safety.
Page 10: Permissible Technical Limits
Safety Instructions MIRO Permissible Technical Limits The product is only intended for the use within the permissible technical limits specified in the data sheets. The following permissible limits must be observed: The ambient temperature limits must not be fallen below or exceeded.
Page 11: Markings On The Product
MIRO Safety Instructions Markings on the Product The identification plate of the product is either a print or a label on a face of the product. Amongst other things, it can contain the following markings, which are explained in detail here.
Page 12: Safety Instructions For Electrical Installation
Safety Instructions MIRO Safety Instructions for Electrical Installation The electrical connection must only be made by authorised expert personnel ac- cording to the wiring diagrams in compliance with IEC 60332-1-2/3 or IEC 60695- 11-21/UL2556 with fire class VW-1. The product is to be installed in an electric cabinet which fulfils the requirements of a fire enclosure according to IEC 62368-1, clause 6.4.8.
Page 13: General Safety Instructions
MIRO Safety Instructions General Safety Instructions Caution! Electrostatic discharges may damage the product! Damage of the product. Observe the general safety precautions when handling electrostatic-discharge-sensitive parts. Caution! Incomplete voltage isolation! Damage of the product. To isolate the voltage from the device, disconnect any supply circuit with its respective isolation device if a redundant power supply is used.
Page 14 Safety Instructions MIRO Caution! Short circuits and damage due to improper repairs and modifications as well as opening of maintenance areas! Fire hazard and damage of the product. It is not permitted to open the product for repair or modification.
Page 15: Security
MIRO IT Security IT Security Note Insecure configured router may compromise applications relevant to security! Follow the information under IT Security – Overview for protecting your router: https://docs.insys-icom.de/itsec/en_itsec_guide.html You will find there a Secure Configuration Guide (https://docs.insys- icom.de/itsec/en_itsec_secure_config_guide.html) for a...
Page 16: Using Open Source Software
Using Open Source Software General Information Our product MIRO contains, amongst others, so-called open-source software that is provided by third parties and has been published for free public use. The open- source software is subject to special open-source software licenses and the copy- right of third parties.
Page 17: Special Liability Regulations
MIRO Using Open Source Software Special Liability Regulations We do not assume any warranty or liability, if the open-source software programs contained in our product are used by the customer in a manner that does not com- ply any more with the purpose of the contract, which is the basis of the acquisition of our product.
Page 18: Version History
Version Modification Release DIN rail mounting revised; temperature range amended Update of the Operating Principle section Addition of MIRO-L2x0 / MIROdul-L2x0 Profile description amended; approvals updated I/O connection amended Update of the Operating Principle section Addition of MIRO-L230 / MIROdul-L230...
Page 19: Device Variants
Device Variants This manual describes different variants of the industrial router MIRO and the in- dustrial router module MIROdul of INSYS icom. The routers are referred to as MIRO or MIROdul in this manual. These are: • MIRO-L100 (router with 1 Ethernet interface and cellular frequency bands...
Page 20: Scope Of Delivery
If a part is missing or damaged, please contact your distributor. • Industrial Router • Quick Installation Guide (MIRO only, 1 per packing unit) • Safety Warnings (MIRO only, 1 per packing unit) The scope of delivery does not include optional accessories. Among other things, the following parts are available from your distributor or INSYS icom: •...
Page 21: Technical Data
100 g (MIRO-L2x0) 42 g (MIROdul-L1x0) 48 g (MIROdul-L2x0) Dimensions (width x height x depth) 26 x 77 x 99 mm (MIRO) 82 x 70 x 17 mm (MIROdul) Depth on DIN rail 92 mm (MIRO) Horizontal pitch on DIN rail 1.5 TE (MIRO)
Page 22 > 100 watt or a PS3 power supply unit, an additional fire protection enclosure is necessary.  The MIRO can also be mounted transverse in a small distribution box with a width of 4.5 TE using a DIN rail holder that is available as an accessory.
Page 23: 7.1.2 Technological Features
10/100 Mbit/s full/half duplex Auto MDI-X; au- tomatic detection of "crossover" or "patch" wir- ing. LTE frequency bands (4G) MIRO-L100/-L200: 1 (2100), 3 (1800), 7 (2600), Band (MHz) 8 (900), 20 (800), 28A (700) LTE Cat 1 (DL: max. 10 Mbit/s, MIRO-L110/-L210: 2 (1900), 4 (2100/1700 UL: max.
Page 24: Connections, Display And Control Elements
Scope of Delivery MIRO Connections, display and control elements Figure 1: MIRO / MIROdul – connections, display and control elements Connection Description ETH 1 Ethernet port 1 (RJ45, 10/100 BT) ETH 2 Ethernet port 2 (RJ45, 10/100 BT, only MIRO/MIROdul-L2x0) ANT.
Page 25 MIRO Scope of Delivery Colour Function blinking 1x for soft reset not availa- green Supply 3x for resetting to present default settings green WAN chain inactive establishing established logged in no signal or green Signal (field strength see logged out...
Page 26: Digital Input/Output
Scope of Delivery MIRO Digital input/output The router has a switchable digital input/output. The digital input/output is config- ured as output in default setting. If the input/output is configured as input, it is low-active, i.e. active, if it is con- nected to GND.
Page 27: Connecting The Connectors
MIRO Scope of Delivery Connecting the connectors The wires are contacted maintenance-free in the connector via a spring clip. Rigid wires (stripped) or stranded wires with end sleeves are only inserted into the con- nectors to clamp them. Stranded wires (braids) without end sleeve are clamped by pushing in the white opener (e.g.
Page 28: Approvals
• NAL (MIRO-L230) The MIROdul router module is an integration module without housing and accord- ingly does not have an approval. Since the MIRO routers with approvals (CE or FCC/IC depending on the version) are internally identical, reference can be made to the MIRO approvals for the approval of a MIROdul application.
Page 29: Mounting
MIRO Mounting 8 Mounting The router MIRO can be mounted in two different ways: • DIN rail mounting • Screw mounting The router module MIROdul can only be mounted via screw mounting. This section describes how you can install the router, connect the power supply and demount it again.
Page 30: Din Rail Mounting
8.1.1 DIN rail mounting with integrated adapter A DIN rail adapter is provided on the MIRO router for DIN rail mounting. Mounting the device to the DIN rail How to mount the router to a DIN rail: Place the device at the DIN rail Hook the upper DIN rail groove into place behind the upper edge of the DIN rail.
Page 31 MIRO Mounting Removing the device from the DIN rail How to remove the router from a DIN rail: The power supply of the switch cabinet is switched off and secured against being switched on accidentally. All connectors at the device are disconnected.
Page 32: 8.1.2 Din Rail Mounting With Accessory Adapter
The MIRO can also be mounted in different orientation with a significantly smaller installation depth using the DIN rail adapter set MIRO that is available as an acces- sory (e.g. for installation in small electrical distribution boxes). To do this, the adapter must be pretensioned and mounted to the front of the MIRO housing be- forehand.
Page 33 MIRO Mounting Mounting the adapter to the housing How to mount the DIN rail adapter to the router housing: Hold the adapter in a way that the retaining spring remains pretensioned and place it on the housing so that the holes for the screws are located over the designated recesses in the housing.
Page 34 Mounting MIRO Mounting the device to the DIN rail How to mount the router to a DIN rail: Place the device at the DIN rail Hook the upper DIN rail groove into place behind the upper edge of the DIN rail.
Page 35 MIRO Mounting Removing the device from the DIN rail How to remove the router from a DIN rail: The power supply of the switch cabinet is switched off and secured against being switched on accidentally. All connectors at the device are disconnected.
Page 36: Screw Mounting
The mounting material is not included and must be selected ac- cording to the underground. The MIRO router must be mounted with two screws (max. Ø 4 mm) to ensure se- cure mounting. The MIROdul router module is to be mounted with three screws (max. Ø 3 mm), whereby only the three holes in the board dimensioned in Figure 11 may be used for mounting.
Page 37 MIRO Mounting Figure 11: Screw mounting – dimensions...
Page 38: Connecting The Power Supply
Mounting MIRO Connecting the power supply Connecting the power supply The device is already mounted. The power supply is connected and switched off. Connect the ground lead of the power supply to the terminal "V-”. Connect the positive lead of the power supply to the terminal "V+”.
Page 39: Commissioning
How to connect the device to a cellular antenna.  The power supply is disabled.  You will need a suitable cellular antenna (available from INSYS icom).  When selecting and mounting the antenna, make sure to comply with CE conformity.
Page 40 Commissioning MIRO Locate the RJ-45 socket of the network card at the PC. Plug one end of the network cable into the RJ45 socket of the PC, and the other end into the ETH 1 socket of the router. ...
Page 41: Operating Principle
MIRO Operating Principle Operating Principle This chapter describes how to operate and configure the router. There are different options for configuration and operation: • Via a web-based user interface (UI). This is displayed and operated using a web browser. Operation via UI and access via HTTPS protocol are described in the following.
Page 42 Operating Principle MIRO Access to the user interface How to access the user interface basically.  The device is ready for operation and you have access to it (refer to Commissioning section).  The device is in delivery condition and default settings.
Page 43: Access Via Https Protocol
MIRO Operating Principle 10.2 Access via HTTPS Protocol The user interface only allows secure configuration using the HTTPS protocol in default settings. The HTTPS protocol allows an authentication of the server (i.e. the router) as well as an encryption of the data transmission. It is not recommended to enable access via the HTTP protocol.
Page 44: Authentication Via An Own Certificate Structure
Operating Principle MIRO 10.2.2 Authentication via an own certificate structure A more secure alternative is to use your own certificate structure and load a self-generated certificate/key combination onto the router and then use this for access via an HTTPS connection.
Page 45: Profiles And Profile Handling
MIRO Operating Principle 10.3 Profiles and Profile Handling The configuration of the router is called profile. Several profiles can be stored on one device so that the configuration of a device can be changed quickly. 10.3.1 Term definitions The following terms or conditions are to be distinguished for profiles: •...
Page 46: Using Several Profiles
Operating Principle MIRO 10.3.3 Using several profiles The versatile possible applications of the router suggest the use of several profiles. The following sections describe the profile handling. 10.3.3.1 Storing a profile When settings made in the opened profile are stored, they will not become effec- tive in the running profile with this.
Page 47 MIRO Operating Principle 10.3.3.4 Creating a profile A new profile can be created from: • the running profile • stored profiles • the default settings A new profile can be created: • In the new UI in the "Administration" menu on the "Profiles" page by clicking (Add) button and selecting "Create new profile"...
Page 48: Ascii Configuration
Operating Principle MIRO 10.3.3.7 Deleting a profile A stored profile can also be deleted again. A stored profile can be deleted: • In the new UI in the "Administration" menu on the "Profiles" page by clicking (Edit) button of the respective profile and a click on the...
Page 49: Profile Mode
MIRO Operating Principle 10.3.5 Profile Mode The router provides two profile modes from firmware version 5.7, the permanent and the volatile profile mode. The configuration of this function is currently only available in the classic web interface. The router is in permanent profile mode in normal operation. All modifications are permanently saved and survive a restart.
Page 50: Maintenance, Repair And Troubleshooting
If a failure occurs during the operation of the product, you will find troubleshooting tips on our support page (https://www.insys-icom.com/en/help/). If you need further support, please contact your reseller or INSYS icom. You can contact our support team via e-mail under support@insys-icom.de.
Page 51: Waste Disposal
According to the new WEEE guidelines, the repurchasing and recycling of INSYS legacy devices for our clients is regulated as follows: Please contact your sales representative by e-mail or phone to initiate the return shipment to INSYS icom. E-mail: info@insys-icom.de Phone: +49 941 58692-0 This regulation applies to all devices which were delivered after August 13, 2005.
Page 52: Declaration Of Conformity
MIRO Declaration of Conformity Hereby, INSYS icom GmbH declares that the device types MIRO and MIROdul are in compliance with Directives 2014/53/EU and 2011/65/EU. The full text of the EC Declaration of Conformity is available under the following Internet address: www.insys-icom.com/manual...
Page 53: Fcc Statement
MIRO FCC Statement FCC Statement Note: Certain variants of this device comply with part 15 of the FCC Rules (this is indicated by the FCC symbol on the label). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause unde- sired operation.
Page 54: Export Restriction
Export Restriction MIRO Export Restriction The chip sets for analogue modems and cellular radio adapters used by INSYS icom GmbH are subject to export restrictions as per US ECCN classification (5A991). Therefore, it is not allowed to export these communication devices into the follow-...
Page 55: Glossary
MIRO Glossary Glossary This describes the most important terms and abbreviations of this manual. APN: Access Point Name, computer name that provides cellular subscribers of the GPRS network with Internet access. AT command: Commands to devices such as modems to set up this device.
Page 56 Glossary MIRO IP net: An Ethernet-based interface that can become a LAN or a WAN inter- face. LAN: Local Area Network; a network of computers which are located rela- tively close to each other. LAN interface: An interface that is assigned to a local network (plant network, machine network, local network);...
Page 57 MIRO Glossary Socket: Data connections that are established using ->TCP or ->UDP use sock- ets for addressing. A socket consists of an IP address and a port (cf. address: street name and number) Switch: A device that can connect several machines with the Ethernet. In con- trast to a hub, a switch will "think”...
Page 58: Tables And Diagrams
Table 9: Permissible line lengths ................27 17.2 List of Diagrams Figure 1: MIRO / MIROdul – connections, display and control elements ....24 Figure 2: MIROdul – connector ................24 Figure 3: Digital input – connection example ............26 Figure 4: Digital open collector output –...
Page 59: Index
MIRO Index Index Access Point Name ......55 GSM ..........55 Accessories ........20 Housing ........... 14 Additional information ....... 8 HTTPS ..........43 Alternative results ......8 Humidity .......... 21 APN ..........55 ICMP ..........55 Assembly ......... 29 Interface ........
Page 60 Index MIRO Power consumption ......21 SIM card .......... 39 Power supply......24, 40 SIM card reader ....... 23 PPP ..........56 SMS..........56 PPPoE ..........56 Socket ..........57 Preface ..........6 Spray water ....... 13, 29 Prerequisites ........8 Switch ..........

This manual is also suitable for:

Mirodul Miro-l100 Miro-l110 Mirodul-l100 Miro-l200 Miro-l210 ... Show all