Related Manuals for Vivo STAND-V101GTU
Summary of Contents for Vivo STAND-V101GTU
- Page 1 Pneumatic Arm Single Monitor Desk Mount SKU: STAND-V101GTU Instruction Manual Assembly Video & Product Info www.vivo-us.com/products/stand-v101gtu...
- Page 2 If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo-us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.
-
Page 3: Package Contents
Package Contents A (x1) B (x1) C (x1) Base Pole Cable Clip D (x1) E (x1) F (x1) Arm Support Lower Arm Gas Spring G (x1) H (x1) I (x1) VESA Bracket Clamp Plate Grommet Plate J (x1) K (x1) L (x1) Soft Pad Cover... -
Page 4: Included Hardware & Tools
Included Hardware & Tools S-A (x4) S-B (x1) S-C (x1) M-A (x4) M6x12mm Spacer M8x25mm M4x12mm Screw Screw Screw M-B (x4) M-C (x4) T-A (x1) T-B (x1) M5x12mm M5 Washer 3mm Allen 4mm Allen Screw Wrench Wrench T-C (x1) 6mm Allen Wrench Tools Needed: Weight Capacity:... -
Page 5: Option 1: Clamp Installation
ASSEMBLY STEPS STEP 1 Option 1: Clamp Installation Attach Clamp Brace (L) to Base (A) Remove adhesive backing from using M6x12mm Screws (S-A) and Soft Pad (J) and apply to the 4mm Allen Wrench (T-B). underside of Clamp Brace (L). Loosen the screws on the back of Clamp (M) using 4mm Allen Wrench (T-B),... - Page 6 Option 1 - Cont’d 10-58mm Desktop Thickness Insert Clamp (M) into the upper four slots on Clamp Brace (L). Tighten the four screws using 4mm Allen Wrench (T-B). Place Clamp Plate (H) onto the Clamp Bolts. Clamp Bolt 50-85mm Desktop Thickness Insert Clamp (M) into the lower four slots on Clamp Brace (L).
- Page 7 Option 1 - Cont’d Place the clamp onto the edge of the desktop and secure by evenly tightening Clamp Bolts using 6mm Allen Wrench (T-C). Clamp Bolt Snap Cover (K) to the back of Clamp Brace (L).
- Page 8 Option 2: Grommet Installation Attach Grommet Plate (I) to Base (A) using M6x12mm Screws (S-A) and 4mm Allen Wrench (T-B). Remove adhesive backing from Soft Pad (J) and apply to underside of Base as shown. Remove one of the Clamp Bolts (M1) from Clamp (M) using 6mm Allen Wrench (T-C).
- Page 9 Option 2 - Cont’d Insert previously removed Clamp Bolt (M1) with Clamp Plate (H) up through the grommet hole and into Base (A). Tighten using 6mm Allen Wrench (T-C). Don’t Have a Grommet Hole? If you do not have an existing hole for installation, drill a hole through your desktop in your desired mounting location using a 3/8”...
- Page 10 STEP 3 Slide Arm Support (D) onto Pole (B) and tighten using 6mm Allen Wrench (T-C). Insert Lower Arm (E) into Arm Support (D) and secure by tightening the set screw using 3mm Allen Wrench (T-A).
- Page 11 STEP 4 Insert Gas Spring Arm (F) into Lower Arm (E) and secure by tightening the set screw using 3mm Allen Wrench (T-A). Attach VESA Bracket (G) to Gas Spring Arm (F) using M8x25mm Screw (S-C), Spacer (S-B) and 6mm Allen Wrench (T-C). Ensure the hex end on Spacer (S-B) is facing up.
- Page 12 STEP 5 Remove Thumbscrew (G1) from the back of VESA Bracket (G). Remove VESA Plate (G2) from the VESA Bracket. Set Thumbscrew aside. Attach VESA Plate (G2) to the back of the monitor using M4x12mm Screws (M-A) or M5x12mm Screws (M-B) with M5 Washers (M-C). Tighten using a Phillips screwdriver. Ensure the arrow on VESA Plate (G2) is pointing up.
- Page 13 Adjusting the Tilt Joint Adjustment Screw Loosen Tilt Joint: Lock Angle Use 6mm Allen Wrench (T-C) to Tighten as much as possible loosen the tilt joint Adjustment using the 6mm Allen Wrench Screw, located on the side of (T-C) to lock the angle. VESA Bracket (G).
- Page 14 STEP 5 With the assistance of a second person, line up the VESA Plate (G2) on your monitor with the VESA Bracket and the Plate Hooks into the pockets of the VESA Bracket (G). 2 Person Mounting is Recommended Gently release the monitor and secure using the previously removed Thumbscrew (G1). Monitor Tilted Too Far? ** See Next Step ** Refer to instructions in next step...
- Page 15 Fine Tune Tilt Angle If the monitor is angled further than intended... Heavy Weighted/ Ultrawide Monitors [ 22lbs - 33lbs ] Firmly Hold Monitor Firmly grasp and hold the monitor in place. Do NOT release monitor until you have completed steps below. Loosen Tilt Joint: With a hand still on the monitor, use 6mm Allen Wrench (T-C) to loosen the tilt joint...
- Page 16 STEP 6 Adjusting Monitor Height Position Mount Arm Turn 10-20x to Set Monitor Height Position the arm horizontally, as shown above, and firmly hold in Turn 6mm Allen Wrench (T-C) 10-20 times place. to obtain proper support for your monitor. Use the guide below to adjust the tension according to the amount of counterbalance Insert...
- Page 17 STEP 7 Remove the top cable cover using a Phillips screwdriver. Remove the bottom cable cover by sliding foward. Oranize cables and reinstall the cable covers.
- Page 18 Adjust as Desired Store Allen Wrenches (T-A,T-B,T-C) in Cover (K).
- Page 19 Love Your New Setup? Tag Us on Social! @ VIVO-us @ vivo_us @VIVOus VIVO...
- Page 20 LAST UPDATED: 8/5/24 REV3 v2.1 Need Help? Get In Touch Monday-Friday from 7:00am-7:00pm CST help@vivo-us.com www.vivo-us.com 309-278-5303 Chat live with an agent! FOR MORE GREAT VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM VIVO-us @vivo_us...
Need help?
Do you have a question about the STAND-V101GTU and is the answer not in the manual?
Questions and answers