Champion M4 Series Installation/Operation Manual With Service Replacement Parts
  1. Manuals
  2. Brands
  3. Champion Manuals
  4. Dishwasher
  5. M4 Series
  6. Installation/operation manual with service replacement parts

Champion M4 Series Installation/Operation Manual With Service Replacement Parts

Undercounter dishwashers, high temperature without built-in booster wash refresh final rinse/high temperature with built-in booster wash refresh final rinse
Hide thumbs Also See for M4 Series:
Table of Contents

Advertisement

Quick Links

Download this manual
Installation/Operation Manual with Service Replacement Parts
UH130
3765 Champion Blvd.,
Winston-Salem, NC 27105
(336) 661-1556 Fax: (336) 661-1660
Toll-free: (800) 858-4477
UH130 M4
High Temperature
without built-in booster
Wash Refresh Final Rinse
2674 N. Service Road, Jordan Station
Ontario, Canada L0R 1S0
(905) 562-4195 Fax: (905) 562-4618
Toll-free: (800) 263-5798
Undercounter Dishwashers
UH130B M4
High Temperature
with built-in booster
Wash Refresh Final Rinse
Issue Date: 6.5.15
Manual P/N
115705 rev. D
For machines beginning with S/N W140946406 and above
M4 Series
Printed in the USA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the M4 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Champion M4 Series

Summary of Contents for Champion M4 Series

  • Page 1 Installation/Operation Manual with Service Replacement Parts Undercounter Dishwashers M4 Series UH130 M4 UH130B M4 High Temperature High Temperature without built-in booster with built-in booster Wash Refresh Final Rinse Wash Refresh Final Rinse UH130 Issue Date: 6.5.15 Manual P/N 115705 rev. D For machines beginning with S/N W140946406 and above 3765 Champion Blvd.,...
  • Page 2 The USGBC and the CaGBC Member Logos are trademarks owned by the U.S. Green Building Council and The Canadian Green Building Council, respectively, and are used by permission. The logos signify only that Champion is a USGBC member and a CaGBC member;...

  • Page 3: Register Your Product Online

    REGISTER YOUR PRODUCT ONLINE Make sure you are connected to the internet then enter an address below: In the U.S.A. http://www.championindustries.com/register In Canada http://www.championindustries.com/canada/register...

  • Page 4: Product Registration Card

    PRODUCT REGISTRATION BY FAX COMPLETE THIS FORM AND FAX TO: (336) 661-1660 in the USA 1-(800) 204-0109 in Canada PRODUCT REGISTRATION CARD Model Serial # Date of Installation: Company Name: Address: (Street) Province Postal Code Telephone #: ( Contact: Installation Company: Address: Telephone #: Contact:...

  • Page 5: Revision History

    Revision History Revision History A revision might be a part number change, a new instruction, or other information that was not available at print time. We reserve the right to make changes to these instructions without notice and without incurring any liability by making the changes. Equipment owners may request a revised manual, at no charge, by calling 1 (800) 858-4477 in the USA or by calling 1 (800) 263-5798 in Canada.

  • Page 6: Limited Warranty

    Industries website (http://www.championindustries.com/register) in the USA or http://www.championindustries.com/canada/ register in Canada or by fax on the form provided at the front of this manual. If warranty registration is not returned to Champion within such period, the warranty will expire after one year from the date of shipment.

  • Page 7: Table Of Contents

    Table of Contents Table of Contents Models UH130, UH130B Revision History ......................i Limited Warranty ...................... ii Model Descriptions ....................v ............Installation - Models UH130, UH130B Receiving - UH130, UH130B ................... 1 Placement - UH130, UH130B .................. 1 Electrical Connections UH130 1 Phase w/o Booster ........... 2 Electrical Connections UH130B 1 and 3 PH Wiring Diagrams ........

  • Page 8: Model Descriptions

    Model Descriptions UH130B Wash Refresh Pumped Final Rinse High temperature hot water sanitizing dishwasher with built-in 40°F/22°C rise booster heater or 70°F/39°C rise booster heater. Two built-in chemical dispensing pumps. Field convertible from single phase to three phase operation. 208-240VAC/60/1 and 3 phase UH130 Wash Refresh Final Rinse High temperature hot water sanitizing dishwasher without built-in booster heater.

  • Page 9: Installation - Models Uh130, Uh130B

    Receiving and Placement - Installation Receiving - UH130, UH130B NOTE: The installation of your dishwasher must be performed by qualified service personnel familiar with food service equipment and must comply with all local health codes. Problems due to improper installation are not covered by the Limited Warranty. NOTE: The installation of the dishwasher must comply with all local electrical, plumbing, health and safety codes or in the absence of local codes, installed in accordance with the applicable...

  • Page 10: Electrical Connections Uh130 1 Phase W/O Booster

    Installation - UH130 Electrical Connections - UH130 1PH without Built-in Booster WARNING: Electrocution or serious injury may result when working on an energized circuit. Disconnect power at the main breaker or service disconnect switch before working on the circuit. Lock-out and tag the breaker or service disconnect switch to indicate that work is being performed on the circuit.

  • Page 11: Electrical Connections Uh130B 1 And 3 Ph Wiring Diagrams

    UH130, UH130B - Installation Electrical Connections - UH130B with Built-in Booster 1PH and 3PH Wiring Diagrams ! ATTENTION ! ALL DISHWASHERS ARE SHIPPED FROM THE FACTORY WIRED FOR SINGLE PHASE OPERATION UNLESS SPECIFIED AT THE TIME OF ORDER. IF YOU ARE CONVERTING A SINGLE PHASE MACHINE TO THREE PHASE BE SURE TO FOLLOW THE BOOSTER WIRING INSTRUCTIONS ON PAGES 7-8.

  • Page 12: Connecting Incoming Power To The Main Terminal Block (1 And 3 Ph)

    Installation - UH130, UH130B Connecting Incoming Power to the Main Terminal Block for 1PH and 3PH Machines with Boosters- UH130B WARNING: Electrocution or serious injury may result when working on an energized circuit. Disconnect power at the main breaker or service disconnect switch before working on the circuit.
  • Page 13 UH130, UH130B - Installation Connecting Incoming Power to the Main Terminal Block for 1PH and 3PH Machines with Boosters- UH130B Refer to the photo below: Remove the lower front dishwasher panel. Remove the retaining fasteners (A) from the swing-out brackets and swing the chemical pump bracket (B) and the chemical circuit board bracket (C) out of the way as shown.
  • Page 14 Installation - UH130, UH130B Connecting Incoming Power to the Main Terminal Block for 1PH and 3PH Machines with Boosters (continued from previous page) Refer to the photo below: Provide a 3 foot/1 meter service loop in the power supply cable to service the machine Route the power cable from the rear of the machine to the terminal block making sure the cable does not touch the booster tank.

  • Page 15: Booster Heater Conversion From 1 To 3 Ph

    UH130, UH130B - Installation Booster Heater Conversion from 1PH to 3 PH Operation ! VERY IMPORTANT ! THE BOOSTER HEATER IS WIRED FOR 1PH OPERATION WHEN SHIPPED. FOLLOW THE INSTRUCTIONS BELOW TO WIRE THE BOOSTER FOR 3PH. WARNING: Electrocution or serious injury may result when working on an energized circuit.
  • Page 16 Installation - UH130, UH130B Booster Heater Conversion from 1PH to 3 PH Operation (continued) ! VERY IMPORTANT ! THE BOOSTER HEATER IS WIRED FOR 1PH OPERATION WHEN SHIPPED. FOLLOW THE INSTRUCTIONS BELOW TO WIRE THE BOOSTER FOR 3PH. Disconnect the existing booster heater wires and change the booster heater element jumpers as shown in the illustration below Connect wires 1H1, 1H2, and 1H3 as shown below.
  • Page 17 UH130, UH130B - Installation Completing the 1PH to 3PH Electrical Conversion ! ATTENTION ! CHANGE THE DATA PLATE ON THE LOWER FRONT PANEL OF THE MACHINE AFTER THE MACHINE IS WIRED FOR 3PH AND THE BOOSTER HEATER IS CONNECTED FOR 3PH. The data plate on the dishwasher lower front panel must be changed after the machine is converted from single phase operation to three phase operation.

  • Page 18: Water Connections - Uh130, Uh130B

    Installation - UH130, UH130B Water Connections - UH130, UH130B ! VERY IMPORTANT ! Make sure the flexible water supply and drain hoses are not kinked. Plumbing connections must allow the machine to be pulled out for service and cleaning. Plumbing connections must comply with national, provincial local plumbing and sanitary codes.

  • Page 19: Drain Connection - Uh130, Uh130B

    UH130, UH130B - Installation Drain Connections - UH130, UH130B ! VERY IMPORTANT ! Do not connect the drain hose to a disposer. The dishwasher will not drain correctly. Refer to the photo below. All models are equipped with a 6 ft.. 5/8" I.D. drain hose. The maximum drain height connection must not exceed 3 ft.[1 m] and must be vented to prevent the wash tank from siphoning.
  • Page 20 Installation - UH130, UH130B Drain Connection - UH130, UH130B (continued) NOTE Plumbing connections must comply with national, provincial local plumbing and sanitary codes. DO NOT REMOVE THE CLAMPS HOLDING THE DRAIN HOSE TO THE BACK OF THE DISHWASHER. DO NOT CONNECT THE DRAIN HOSE TO A DISPOSER. DO NOT REDUCE THE SIZE OF THE DRAIN HOSE CONNECTION NOR USE A DOMESTIC DRAIN FITTING.
  • Page 21 UH130, UH130B - Installation Drain Connection - UH130, UH130B For an Indirect Drain Connection: A 1" [25.4mm] minimum air gap must be provided between the outlet of the dishwasher drain hose and the flood-level rim of the floor drain, floor sink or any other locally approved drain receptacle.

  • Page 22: Booster Fill Switch - (Filling The Booster For The First Time)

    Installation - UH130B Booster Fill Switch - (Filling the booster tank for the first time) UH130B only ! CAUTION ! AVOID PERMANENT DAMAGE TO THE BOOSTER HEATER DO NOT TURN THE DISHWASHER POWER SWITCH ON WHEN FILLING THE BOOSTER FOR THE FIRST TIME. THE BUILT-IN BOOSTER TANK WAS DRAINED BEFORE SHIPMENT AND MUST BE REFILLED BEFORE OPERATING THE DISHWASHER.
  • Page 23 UH130B - Installation Booster Fill Switch - (Filling the booster tank for the first time) UH130B only PUSH AND HOLD the booster fill switch in the FILL position until water starts filling inside the wash compartment. Release the FILL switch. PUSH the booster fill switch to the ON position and release.

  • Page 24: Chemical Connections Uh130, Uh130B

    Installation - UH130, UH130B Chemical Connections UH130, UH130B ! VERY IMPORTANT ! ALWAYS USE A COMMERCIAL-GRADE NON-CHLORINATED DETERGENT. PLACE THE CHEMICAL SUPPLY CONTAINERS AS CLOSE TO THE MACHINE AS POSSIBLE. DO NOT ELEVATE THE CHEMICAL CONTAINERS ABOVE THE FINISHED FLOOR. ! VERY IMPORTANT ! Contact a chemical supplier for detergent and rinse-aid chemicals.

  • Page 25: Pumps And Injection Points - Detergent And Rinse-Aid Dispensing Pumps

    UH130, UH130B - Installation Pumps and Injection Points - Detergent and Rinse-aid Dispensing Pumps UH130, UH130B ! VERY IMPORTANT ! ALWAYS USE A COMMERCIAL-GRADE NON-CHLORINATED DETERGENT. PLACE THE CHEMICAL SUPPLY CONTAINERS AS CLOSE TO THE MACHINE AS POSSIBLE. DO NOT ELEVATE THE CHEMICAL CONTAINERS ABOVE THE FINISHED FLOOR. Injection Point Locations 1.
  • Page 26 Blank Page This Page Intentionally Left Blank...

  • Page 27: Pumps And Injection Points - Detergent And Rinse-Aid Dispensing Pumps

    UH130, UH130B - Installation Pumps and Injection Points - Detergent and Rinse-aid Dispensing Pumps UH130, UH130B Priming the Dispensing Pumps ! VERY IMPORTANT ! The chemical dispensing pumps must be primed before operating the dishwasher and whenever the chemical container is changed. TEMPERATURE DETERGENT POWER...

  • Page 28: Pump And Fill Adjustments - Detergent And Rinse-Aid Dispensing Pumps

    Installation - UH130, UH130B Detergent and Rinse-aid Dispensing Pumps - Pump and Fill Adjustments UH130, UH130B ! ATTENTION ! The amount of dispensed chemical is determined by the run time of the dispensing pump. Refer to the photo below: 1. The chemical dispensing pump run and the tank fill adjustment screws are located on the end of the chemical circuit board swing-out bracket.
  • Page 29 UH130, UH130B - Installation Detergent and Rinse-aid Dispensing Pumps - Pump and Fill Adjustments UH130, UH130B Refer to the photo below: To adjust the amount of chemicals dispensed by the pumps: Make sure the chemical containers are full and the pick-up tubes are in their proper containers. Turn the dishwasher power switch ON.

  • Page 30: Operation - Models Uh130, Uh130B

    UH130, UH130B Operation - Operation - UH130, UH130B Loading Dish Racks ! VERY IMPORTANT ! DO NOT OVERLOAD THE DISH RACK. LOAD ONE DISH RACK INTO THE MACHINE AT A TIME. Prescrap and rinse the wares before loading to remove large food particles. Load soiled wares into the dish rack.
  • Page 31 UH130, UH130B - Operation Loading Dish Racks (continued) Load pots and pans in a flat-bottom rack. Load utensils in a single layer in a flat-bottom rack. Load cups and bowls in a flat-bottom rack. NEVER stack dish racks. Wash one dish rack at a time.

  • Page 32: Normal Wash Mode - Uh130, Uh130B

    Operation - UH130, UH130B Operation - UH130, UH130B Normal Wash Mode UH130B Control Panel TEMPERATURE DETERGENT POWER RINSE AID WASH RINSE OFF/DRAIN PRIME START ON-OFF/DRAIN Prime Start Power Switch Push button Push button Wash Temperature Final Rinse Temperature In-cycle Light Digital Display Digital Display Close the dishwasher front door.
  • Page 33 Blank Page This Page Intentionally Left Blank...

  • Page 34: Rinse Sentry Mode - Uh130B Only

    UH130, UH130B Operation - UH130B Rinse Sentry Mode ! ATTENTION ! DOOR LEFT OPEN DURING WASH CYCLE If the dishwasher door is left open for more than 5 seconds during the normal wash mode, then the dishwasher cycle will reset to the beginning of the normal wash cycle. ! ATTENTION ! RINSE SENTRY MODE WILL EXTEND WASH CYCLE TIME In the event that the final rinse temperature has not reached 180-195ºF/82-91ºC after the...

  • Page 35: Drain Mode - Uh130, Uh130B

    UH130, UH130B - Operation UH130, UH130B - Operation Push the illuminated power switch down to the OFF/DRAIN position. The power switch light will go out. The cycle light will illuminate and the machine will drain. The machine, will flush, perform 3 short drain cycles and then drain completely. The cycle light will go out indicating that the drain cycle is complete.

  • Page 36: Cleaning - Models Uh130, Uh130B

    Cleaning - UH130, UH130B Cleaning - UH130, UH130B VERY IMPORTANT DRAIN AND CLEAN THE DISHWASHER EVERY 2 HOURS OF CONTINUOUS OPERATION, AFTER EACH MEAL PERIOD, AND AT THE END OF THE DAY. All Models Cleaning the wash tank: Remove the upper and lower spray arms and flush clean in a sink. Remove the scrap screen taking care that debris does not fall off the screen and into the wash tank or sump.

  • Page 37: Cleaning The Wash Arms - Uh130, Uh130B

    UH130, UH130B - Cleaning UH130, UH130B - Cleaning UH130, UH130B Unscrew the retaining screw from the upper and lower interchangeable spray arms. Flush the spray arms clean in a sink. Be sure to flush the wash arm bearings. Retaining Screw Wash Arm Bearing UH130...
  • Page 38 Cleaning - UH130, UH130B Cleaning - UH130, UH130B UH130, UH130B Scrap Screen and Sump Strainer Scrap Lift the scrap screen straight up and out of the machine to prevent food particles from falling into Screen the tank sump. Flush the scrap screen in a remote sink making sure to back-flush both side of the screen.

  • Page 39: Cleaning Scrap Screen And Sump Strainer - Uh130, Uh130B

    UH130, UH130B - De-liming De-liming Cautions and Warnings A de-liming agent must be used in accordance with your chemical supplier's instructions. DANGER: Death or serious injury may result when de-liming solution is mixed with sodium hypochlorite sanitizing agent. Mixing may cause hazardous gases to form. De-liming solution and other acids must never be mixed with chlorine, iodine, bromine, or fluorine.

  • Page 40: Daily Maintenance

    Maintenance - UH130, UH130B UH130, UH130B - Maintenance Follow the maintenance schedules below to keep the dishwasher operating most efficiently. Daily Maintenance Make sure the water supply is on and that the drain is not clogged. Check the temperature gauges and/or displays to ensure they are operating. Make sure the dish racks are in good condition.

  • Page 41: Troubleshooting- Uh130, Uh130B

    UH130, UH130B - Troubleshooting Troubleshooting UH130, UH130B Illustrations Page Troubleshooting Chart - ..............34 UH130, UH130B Wash Codes Temperature Display Board - .......... 35 UH130, UH130B Rinse Codes Temperature Display Board - ........... 36 UH130, UH130B Booster Codes Temperature Display Board - ........
  • Page 42 Troubleshooting - UH130, UH130B Condition Cause Solution Dishwasher will not run. Door not closed. Close door completely. Main power OFF. Check breaker on panel. Dishwasher OFF. Turn dishwasher power switch ON. Low or no water. Main water supply off. Open supply valve. Fill hose kinked.
  • Page 43 UH130, UH130B - Digital Temperature Display Codes Digital Temperature Display Codes Display codes that appear in the display windows indicate the operating condition of the machine. Refer to the illustrations below for the meaning of the codes. Wash Display Codes CAUSE WASH DISPLAY CODE Wash temperature...
  • Page 44 Digital Temperature Display Codes - UH130, UH130B Rinse Display Codes CAUSE RINSE DISPLAY CODE Rinse temperature 1 5 9 is below 100˚F RINSE TEMP WASH TEMP 1 5 6 Rinse temperature is above 200˚F WASH TEMP RINSE TEMP Booster tank is empty 1 4 9 &...

  • Page 45: Display Codes

    UH130, UH130B - Digital Temperature Display Codes Booster Display Codes Error Codes for Booster and Final Rinse Thermistors Only. CAUSE DISPLAY CODES 1 5 0 Booster overtemp lockout because booster temperature is greater than 210˚F. RINSE TEMP WASH TEMP NOTE: Booster is locked out for 10 minutes before being re-energized.
  • Page 46 Timer Board Connection Diagram - UH130, UH130B        ...
  • Page 47 UH130, UH130B - Timer Board Diagnostic Testing Diagnostic Testing for the Solid State Timer Board, P/N 0712105 Beginning with S/N W081217467 and above Before testing, Press the dishwasher power switch to OFF/DRAIN and allow the machine to complete the drain cycle. Check the incoming voltages.
  • Page 48 Digital Temperature Display Board - UH130, UH130B Power Neutral...
  • Page 49 UH130, UH130B - Digital Temperature Display Board...
  • Page 50 Digital Temperature Display Board - UH130, UH130B...
  • Page 51 UH130B Only - Booster Heater/Wash Tank Heater Interlock Circuit Operation Booster Heater/Wash Tank Heater Interlock Circuit Operation For Models UH130B The booster heater/wash tank heater interlock circuit removes power from the wash tank heater whenever the booster heater contactor energizes. The illustration below shows how the booster heater contactor is wired.
  • Page 52 Blank Page This Page Intentionally Left Blank...

  • Page 53: Service Replacement Parts

    Service Replacement Parts Service Replacement Parts Illustrations Page Wash Pump/Motor Assembly - UH130, UH130B ..............46 Base Assembly - UH130, UH130B ..................48 Fill Piping Assembly - UH130, UH130B ................52 Fill Solenoid Valve - UH130, UH130B ................54 Fill Chute Assembly - UH130, UH130B ................56 Chemical Dispensing Pumps - UH130, UH130B ..............58 Booster Assembly - UH130B Only ..................60 Power Input Block and Cord Assemblies - UH130, UH130B ..........62...

  • Page 54: Wash Pump/Motor Assembly - Uh130, Uh130B

    Wash Pump/Motor Assembly - UH130, UH130B...
  • Page 55 UH130, UH130B - Wash Pump/Motor Assembly Item Part Description Qty. 0512347 CAPACITOR 40µF 0512101 PUMP/MOTOR ASSEMBLY COMPLETE 115VAC/60/1 0313394 BRACKET, WASH PUMP 0512185 BOLT, HEX FLANGE 1/4-20 X 3/8" SST 110285 GASKET 114139 SEAL 0512345 IMPELLER 0501478 WASHER, PLAIN, 17/64" 106482 WASHER, LOCK, 1/4"...

  • Page 56: Base Assembly - Uh130, Uh130B

    Base Assembly - UH130, UH130B To upper wash hub UL130 Only To rinse UL130 Only 16 17 Detail on pgs. 106-107 Detail on pgs. 102-105 35 36...
  • Page 57 UH130, UH130B - Base Assembly Item Part Description Qty. 0512136 SCREEN, SCRAP ASSY. 0513324 FLANGE, PUMP SUCTION 0513677 O-RING 0512169 HEATER, 120VAC 750W) (UL130) 0512099 O-RING 0508872 ADAPTOR, THERMOMETER (UL130 Only) 0512107 THERMOMETER, WASH TANK (UL130 Only) 108954 NUT, GRIP 6-32 WITH NYLON INSERT SST 113604 THERMOSTAT, HI-LIMIT BI-METAL SNAP, 212°F 0512299...
  • Page 58 Base Assembly - UH130, UH130B Item Part Description Qty. 0512322 CLAMP, HOSE 0513339 HOSE, OVERFLOW ( UH230, UH230B, UH330B) 0712236 TUBE, OVERFLOW GUARD (UH230, UH230B) ---- 0712236-1 TUBE, OVERFLOW GUARD (UH330B ONLY) 109835 SCREW #8 X 1/2" SELF-TAPPING SST 0512185 BOLT, HEX FLANGE 1/4-20 X 3/8"...
  • Page 59 Blank Page This Page Intentionally Left Blank...

  • Page 60: Fill Piping Assembly - Uh130, Uh130B

    Fill Piping Assembly - UH130, UH130B Note: This is a 3/4" From Hot Water garden hose fitting Supply Fill Valve Assembly on Next Page To Booster Inlet UH130B To Fill Chute UH130, UL130...
  • Page 61 UH130, UH130B - Fill Piping Assembly Item Part Description Qty. 0502653 ELBOW, 90° 3/8" MPT X 1/2" HOSE 0512185 BOLT, HEX FLANGE 1/4-20 X 3/8" SST 0300065 SUPPORT, VALVE 0300203 CLAMP, VALVE 0502618 HOSE BARB, 1/2" X 3/8" MPT 0512985 CLAMP, HOSE 0509526 HOSE, 1/2"...

  • Page 62: Fill Solenoid Valve - Uh130, Uh130B

    Fill Solenoid Valve - UH130, UH130B...
  • Page 63 UH130, UH130B - Fill Solenoid Valve Item Part Description Qty. 0504952 VALVE, FILL 5.0 GPM 0502803 SCREEN, VALVE STRAINER 0502804 GASKET, CAP 0504958 WASHER, FLOW 5.0 GPM ( 0502811 KIT, REBUILD 0505229 GUIDE 0501406 SCREW, SLOT SS RH 8-32 X 1/2" 0505235 COIL, 115V 60HZ 10W 0502807...

  • Page 64: Fill Chute Assembly - Uh130, Uh130B

    Fill Chute Assembly - UH130, UH130B...
  • Page 65 UH130, UH130B - Fill Chute Assembly Item Part Description Qty. 107417 HOSE, RUBBER 1/2" ID X .84" OD 0502666 HOSE, 1/8" ID X 1/4" OD PVC 0502667 HOSE, 1/4" ID X 3/8" OD PVC 100194 NUT, GRIP 10-32 W/NYLON INSERT 0503722 NUT, HEX 10-32 SST 0507709...

  • Page 66: Chemical Dispensing Pumps - Uh130, Uh130B

    Chemical Dispensing Pumps - UH130, UH130B IMPORTANT: Check Items #9 and #10 every 6 months and replace if stretched or worn. RINSE-AID DETERGENT...
  • Page 67 UH130, UH130B - Chemical Dispensing Pumps Item Part Description Qty. 0501869 STRAINER 0306363 TUBE, 3/8" ID X 12" LG. STIFFENER 0505483 LABEL, RINSE-AID HOSE 112883-1 TUBING, 1/8" OD X 1/16" ID 0503695 LABEL, DETERGENT HOSE 0502667 HOSE, 1/4" ID X 3/8" OD PVC 0501519 TIE, NYLON 4"...
  • Page 68 Booster Assembly - UH130B 11 12...
  • Page 69 UH130B - Booster Assembly Item Part Description Qty. 0512985 CLAMP, SS GEAR-MIN. 1/2" 107417 HOSE, RUBBER 1/2" ID X .84" OD 0513314 TEE, RINSE THERMISTOR 10 kΩ, 2-WIRE 0513310 110562 THERMOSTAT, HIGH LIMIT 240°F 108954 NUT, GRIP 6-32 W/NYLON INSERT SST 0512185 BOLT, HEX FLANGE, 1/4-20 X 3/8"...

  • Page 70: Power Input Block And Cord Assemblies - Uh130, Uh130B

    Power Input Block and Cord Assemblies - UH130, UH130B...
  • Page 71 UH130, UH130B - Power Input Block and Cord Assemblies Item Part Description Qty. 0313396 COVER, BOX WIRING 0501411 SCREW, 10-32 X 1/4", TRUSS HD. 0512432 CONTACTOR, 3-POLE 120VAC COIL 0509527 BLOCK, TERMINAL, 4-POLE 103310 LUG, GROUND 0313395 BOX, WIRING 107964 BUSHING, STRAIN RELIEF, SMALL 0503592 LABEL, GROUND...

  • Page 72: Timer Control Board Assembly - Uh130, Uh130B

    Timer Control Board Assembly - UH130B Front View Rear View...
  • Page 73 UH130B - Timer Control Board Assembly Item Part Description Qty. 0313397 BOX, CONTROL BOARD 0712105 TIMER CKT. BD. 0501464 SCREW, 10-24 X 3/8; TRUSS HD. SST 0512373 FUSE, 4A 250V 0313398 COVER, BOX 0501411 SCREW, 10-32 X 1/4" SST 0501373 SWITCH, BOOSTER FILL 0512973 STANDOFF...

  • Page 74: Wash/Rinse Spray Arm And Drain Valve - Uh130, Uh130B

    Wash/Rinse Spray Arm and Drain Valve - UH130, UH130B...
  • Page 75 UH130, UH130B - Wash/Rinse Spray Arm and Drain Valve Item Part Description Qty. 0501478 WASHER, 17/64" ID X 9/16" OD SST 107967 NUT, HEX SST 1/4-20 NYLON INSERT H35509-1 HUB, UPPER WASH ARM 107873 WASHER, PACKING 110215 SCREW, RETAINING 0502571 CLAMP, HOSE GEAR HOSE 1-1/2”...

  • Page 76: Control Panel - Uh130, Uh130B

    Control Panel - UH130, UH130B...
  • Page 77 UH130, UH130B - Control Panel Item Part Description Qty. 0512221 SWITCH, ROCKER DPST 250V NEON 0512213 SWITCH, PIEZIO 0512232 LIGHT, INDICATOR, GREEN 0512226 SWITCH, ROCKER RND SPDT MOMENTARY 0501408 SCREW, TRUSS PHIL. SST 8-32 X 1/4" 0513540 LABEL, FACIA 0313418 PANEL, FACIA 0512357 STANDOFF, LED DISPLAY BOARD...

  • Page 78: Panels- Uh130, Uh130B

    Panels- UH130, UH130B...
  • Page 79 UH130, UH130B - Panels Item Part Description Qty. 0313406 PANEL, FRONT WITHOUT GAUGE HOLE 0313407 PANEL, FRONT WITH GAUGE HOLE 0513735 GASKET 109812 GAUGE, PRESSURE 0-60 PSI 100779 SCREW 1/4-20 X 5/8" TRUSS SS PHIL 0513659 FITTING, 1/4" TUBE X 1/8" FNPT PP 107928 TUBING, 1/4"...

  • Page 80: Door Assembly - Uh130, Uh130B

    Door Assembly - UH130, UH130B...
  • Page 81 UH130, UH130B - Door Assembly Item Part Description Qty. 0713136 DOOR ASSEMBLY 0513558 GASKET, DOOR TOP 0513727 GASKET, DOOR SIDE 0713428 HINGE, RH ASSY 0501476 WASHER, 9/32" X 5/8" OD SS 0501422 BOLT, HEX SS 1/4-20 X 1-1/2" 0513332 SPRING, DOOR 0713429 HINGE, LH ASSY 0313430...
  • Page 82 Dish Racks, Line Strainer, PRV...

  • Page 83: Dish Racks

    Dish Racks Item Part Description Qty. 101273 DISH RACK, FLAT-BOTTOM 101285 DISH RACK, PEG...
  • Page 84 Blank Page This Page Intentionally Left Blank...

  • Page 85: Electrical Schematics And Timing Charts

    Electrical Schematics Electrical Schematics and Timing Charts Illustrations Page Electrical Schematic - High Temperature Models - UH130, UH130B ........78 Timing Charts - UH130, UH130B ..................79...
  • Page 86 Electrical Schematic - UH130, UH130B SINGLE PHASE THREE PHASE UH130, UH130B, UH230, UH230B...
  • Page 87 UH130, UH130B - Timing Charts...
  • Page 88 Blank Page This Page Intentionally Left Blank...

This manual is also suitable for:

Uh130 m4Uh130b m4

Table of Contents