Advertisement
Page 1 of 13
CP0496BL
FITTING INSTRUCTIONS FOR CP0496BL
AERO-STYLE CRASH PROTECTORS
DUCATI STREETFIGHTER V4 2020-
T
.
HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE
S
.
OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY
D
.
O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT
P
.
LEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF
.
MOUNTING TO THE BIKE
I
,
N THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS
.
THESE RUBBER WASHERS CAN BE THROWN AWAY
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
WWW.RG-RACING.COM
R&G Racing
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for R&G CP0496BL
Summary of Contents for R&G CP0496BL
- Page 1 Page 1 of 13 CP0496BL FITTING INSTRUCTIONS FOR CP0496BL AERO-STYLE CRASH PROTECTORS DUCATI STREETFIGHTER V4 2020- HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT...
-
Page 2: Tools Required
Page 2 of 13 CP0496BL TOOLS REQUIRED GENERAL TORQUE SETTINGS • 14mm & 19mm A/F SOCKET & WRENCH M4 BOLT = 8Nm M5 BOLT = • TORQUE WRENCH (UP TP 90Nm) M6 BOLT = M8 BOLT = 20Nm 0 BOLT = 40Nm... - Page 3 Page 3 of 13 CP0496BL LHS EXPLODED ASSEMBLY VIEW RHS EXPLODED ASSEMBLY VIEW R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
- Page 4 Page 4 of 13 CP0496BL FITTING PICTURES Picture 1 Picture 2 Picture 3 Picture 4 Picture 5 Picture 6 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
-
Page 5: Fitting Instructions
Page 5 of 13 CP0496BL FITTING INSTRUCTIONS • Starting on the RHS of the bike, remove the engine mounting bolt using a 14mm socket, as shown in picture 1. • Wind in the extension bolt (item 2) by hand into the vacant engine mounting hole as shown in picture 2, then fully tighten up to 90Nm using a 19mm socket and torque wrench. - Page 6 Page 6 of 13 CP0496BL NOTICE DE MONTAGE POUR CP0496BL PROTECTIONS CRASH DUCATI STREETFIGHTER V4 2020- E KIT CONTIENT LES ARTICLES ILLUSTRES ET ETIQUETES SUR LA PAGE ERTAINES PARTIES PEUVENT ETRE PRESENTES UNIQUEMENT POUR LA CLARTE DES INSTRUCTIONS E PAS PROCEDER AU MONTAGE TANT QUE VOUS N...
-
Page 7: Outils Requis
Page 7 of 13 CP0496BL OUTILS REQUIS VALEURS DE SERRAGE • Clé à cliquet + douilles 14mm & 19mm M4 BOULON = 8Nm M5 BOULON = • Clé dynamométrique (jusqu’à 90Nm) M6 BOULON = M8 BOULON = 20Nm 0 BOULON = 40Nm M12 BOULON = 40Nm LÉGENDE... -
Page 8: Côté Droit
Page 8 of 13 CP0496BL CÔTÉ GAUCHE CÔTÉ DROIT R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com... -
Page 9: Notice De Montage
Page 9 of 13 CP0496BL NOTICE DE MONTAGE • En commençant du côté droit de la moto, retirez le boulon de fixation du moteur à l'aide d'une douille de 14 mm, comme indiqué sur la photo 1. • Enrouler le boulon d'extension (article 2) à la main dans le trou de montage de moteur vide comme indiqué... - Page 10 Page 10 of 13 CP0496BL MONTAGEANLEITUNG FÜR CP0496BL AERO STURZPADS DUCATI STREETFIGHTER V4 2020- EILE SIND AUF DEN FOLGENDEN EITEN ABGEBILDET UND GEKENNZEICHNET IE ABGEBILDETEN EILE DIENEN LEDIGLICH ZUR RKLÄRUNG Ü BERPRÜFEN IE ZUERST DASS ALLE EILE VORHANDEN SIND ESEN...
- Page 11 Page 11 of 13 CP0496BL SIE BENÖTIGEN FOLGENDE WERKZEUGE; ALLGEM. ANZUGSDREHOMENT • 14mm & 19mm Steckschlüssel M4 SCHRAUBE = 8Nm M5 SCHRAUBE = • Drehmomentschlüssel (bis 90 Nm) M6 SCHRAUBE = M8 SCHRAUBE = 20Nm 0 SCHRAUBE = 40Nm M12 SCHRAUBE = 40Nm...
- Page 12 Page 12 of 13 CP0496BL RECHTE SEITE -EXPLOSIONSZEICHNUNG MONTAGE – BILDER R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
- Page 13 Page 13 of 13 CP0496BL MONTAGEANLEITUNG • An der rechten Seite des Motorrades beginnend, entfernen Sie die Montageschraube für den Motor mit einem 14mm Steckschlüssel wie in Abbildung 1 abgebildet. • Die Verlängerungsschraube (Artikel 2) in die freie Montageöffnung für den Motor mit der Hand eindrehen wie in Abbildung 2 abgebildet, dann komplett festziehen bis 90Nm mit einem 19mm Steckschlüssel und Drehmomentschlüssel.
Need help?
Do you have a question about the CP0496BL and is the answer not in the manual?
Questions and answers