Advertisement
Available languages
Available languages
Quick Links
Page 1 of 9
FITTING INSTRUCTIONS FOR CP0466 CRASH PROTECTORS
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF
P
LEASE NOTE THAT IN CASES WHERE KITS ARE PACKED WITH RUBBER WASHERS HOLDING THE COMPONENTS
ONTO THE BOLT
T
HE PARTS SHOWN MAY BE REPRESENTATIVE ONLY
D
IGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE TO DOWNLOAD FROM
GENERAL TORQUE SETTINGS
M4 BOLT = 8Nm
M5 BOLT = 12Nm
M6 BOLT = 15Nm
M8 BOLT = 20Nm
M10 BOLT = 40Nm
Unit
Tel: +44 (0)
420 89007 Fax: +44 (0)
1
FOR BMW S1000RR '19-
MOUNTING TO THE BIKE
–
THE RUBBER WASHERS SHOULD BE THROWN AWAY
, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
1
420 87301
1
(
FOR CLARITY OF INSTRUCTIONS ONLY
TOOLS REQUIRED
•
T50 Torx Key/Socket
•
17mm Socket and Ratchet
•
Torque Wrench
•
Scissor Jack
R&G
www.rg-racing.com
CP0466
!
.
-
.
WWW
RG
RACING
COM
Email:
info@rg-racing.com
)
Advertisement
Related Manuals for R&G CP0466 Series
Summary of Contents for R&G CP0466 Series
- Page 1 Page 1 of 9 CP0466 FITTING INSTRUCTIONS FOR CP0466 CRASH PROTECTORS FOR BMW S1000RR ’19- THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW. DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT. LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF MOUNTING TO THE BIKE LEASE NOTE THAT IN CASES WHERE KITS ARE PACKED WITH RUBBER WASHERS HOLDING THE COMPONENTS –...
- Page 2 Page 2 of 9 CP0466 This Kit Contains: Item = 2x CRASH PROTECTOR BOBBINS (B0061) W / 10mm COMPRESSION-SLEEVE (CS341) Item 2 = 2x BOBBIN SPACERS 24mm LENGTH (S0142) Item 3 = 2x M10 x 1.5 x 100mm HEX HEAD BOLTS Item 4 = 2x BOBBIN CAPS W/BUBBLE STICKER AFFIXED (BC0002) Item 5 = 2x...
-
Page 3: Fitting Instructions
Page 3 of 9 CP0466 FITTING INSTRUCTIONS Picture 1 Picture 2 Picture 3 Picture 4 Picture 5 Picture 6 R&G Unit , Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0) 420 89007 Fax: +44 (0) 420 87301 www.rg-racing.com Email: info@rg-racing.com... - Page 4 Page 4 of 9 CP0466 • Before fitting the R&G crash protectors, it is advised that a scissor jack is positioned underneath the bike at a suitable mounting point to support the weight of the engine during fitment, as shown in picture 1. A small piece of wood should also be placed between the jack and the mounting point to help to spread the load.
- Page 5 Page 5 of 9 CP0466 NOTICE DE MONTAGE CP0466 PROTECTIONS CRASH FOR BMW S1000RR ’19- E KIT CONTIENT LES ARTICLES EXPOSES CI DESSOUS VERIFIER QUE TOUTES LES PIECES SOIENT PRESENTES AVANT DE PROCEDER AU MONTAGE La façon dont le kit est emballé ne correspond pas forcément à la façon de monter les pièces sur la moto OTEZ QUE SI LES KITS SONT EMBALLES AVEC DES RONDELLES EN CAOUTCHOUC SERVANT A TENIR LES COMPOSANTS...
- Page 6 Page 6 of 9 CP0466 Le kit contient : Article = 2x PROTECTIONS CRASH (B0061) W / 10mm MANCHON DE COMPRESSION (CS341) Article 2 = 2x ENTRETOISES DE BOBINE 24mm (S0142) Article 3 = 2x M10 x 1.5 x 100mm BOULONS Article 4 = 2x STICKERS DE CAPUCHONS DE BOBINE (BC0002) Article 5 = 2x M10 RONDELLES Article 6 = 2x RONDELLES ANTI-VIBRATION (LW0001)
- Page 7 Page 7 of 9 CP0466 • Avant d'installer les protections R&G, il est conseillé de placer un cric ciseau sous la moto à un endroit approprié pour supporter le poids du moteur pendant le montage, comme indiqué sur la photo 1. Un petit morceau de bois doit également être placé entre le cric et le point de support pour aider à...
-
Page 8: Sie Benötigen Folgendes
Page 8 of 9 CP0466 MONTAGEANLEITUNG FÜR CP0466 STURZPADS FÜR BMW S1000RR ’19- ALLE KIT-TEILE SIND UNTEN ABGEBILDET UND GEKENNZEICHNET. ÜBERPRÜFEN SIE, DASS ALLE TEILE VORHANDEN SIND, BEVOR SIE MIT DER MONTAGE BEGINNEN. HINWEIS: DIE VERPACKUNG DER TEILE STELLT NICHT DIE REIHENFOLGE DER MONTAGE DAR. HINWEIS FÜR KITS MIT PLASTIKUNTERLEGSCHEIBEN AN DEN SCHRAUBEN –... - Page 9 Page 9 of 9 CP0466 Inhalt des Kits: Artikel = 2x STURZPAD BOBBINS (B0061) W / 10mm KOMPRESSIONSHÜLSE (CS341) Artikel 2 = 3x DISTANZHALTER 24mm LÄNGE (S0142) Artikel 3 = 2x M10 x 1,5 x 100mm SECHSKANTSCHRAUBE Artikel 4 = 2x STURZPAD-KAPPEN / BUBBLE-AUFKLEBER BEREITS MONTIERT (BC0002) Artikel 5 = 2x M10 UNTERLEGSCHEIBEN Artikel 6 = 2x ZAHNSCHEIBEN (LW0001) •...