Advertisement
Quick Links
CP0478
PAGE 1 OF 13
FITTING INSTRUCTIONS FOR CP0478 CRASH PROTECTORS
TRIUMPH SCRAMBLER 1200 2019-
T
.
HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE
S
.
OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY
D
.
O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT
P
.
LEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF
.
MOUNTING TO THE BIKE
I
,
N THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS
.
THESE RUBBER WASHERS CAN BE THROWN AWAY
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
WWW.RG-RACING.COM
R&G Racing
Unit 1, Shelleys Lane, East Worldham, Alton, Hampshire GU34 3AQ.
Tel: +44 (0)1420 89007 Fax +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com
Advertisement
Related Manuals for R&G CP0478
Summary of Contents for R&G CP0478
- Page 1 CP0478 PAGE 1 OF 13 FITTING INSTRUCTIONS FOR CP0478 CRASH PROTECTORS TRIUMPH SCRAMBLER 1200 2019- HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT...
-
Page 2: Tools Required
PAGE 2 OF 13 CP0478 TOOLS REQUIRED GENERAL TORQUE SETTINGS • M4 BOLT = 8Nm 30 & 55 TORX • M5 BOLT = SOCKET SET TO INCLUDE 17mm SOCKET AND EXTEN- SION BAR M6 BOLT = • 17MM SPANNER M8 BOLT = 20Nm... - Page 3 CP0478 PAGE 3 OF 13 ASSEMBLY DIAGRAM 1—LHS ASSEMBLY DIAGRAM 1—RHS R&G Racing Unit 1, Shelleys Lane, East Worldham, Alton, Hampshire GU34 3AQ. Tel: +44 (0)1420 89007 Fax +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
-
Page 4: Fitting Instructions
PAGE 4 OF 13 CP0478 Picture 1 Picture 2 FITTING INSTRUCTIONS Left Hand Side (as you sit on the bike) • Before fitting the R&G crash protectors, it is advised that a jack is positioned underneath the bike at a suitable point to support the weight of the engine during fitment. - Page 5 CP0478 PAGE 5 OF 13 CONSUMER NOTICE The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
- Page 6 PAGE 6 OF 13 CP0478 NOTICE DE MONTAGE POUR CP0478 PROTECTIONS CRASH E KIT CONTIENT LES ARTICLES EN PHOTO ET ETIQUETTES SUR LA PAGE LES PARTIES PRESENTÉES PEUVENT ETRE UNIQUEMENT REPRESENTATIVES POUR LA CLARTE DES INSTRUCTIONS E PAS ROCÉDER AU MONTAGE AVANT DE VOUS ÊTRES ASSURE QUE TOUTES LES PIECES SOIENT PRÉSENTES SVP, ’...
-
Page 7: Outils Requis
CP0478 PAGE 7 OF 13 OUTILS REQUIS VALEURS DE SERRAGE • Clé Torx 30 & 55 M4 BOULON = 8Nm M5 BOULON = • Clé à cliquet + douille 17mm et extension M6 BOULON = • Clé à molette 17mm... - Page 8 PAGE 8 OF 13 CP0478 SCHEMA 1 – GAUCHE SCHEMA 1 – DROITE R&G Racing Unit 1, Shelleys Lane, East Worldham, Alton, Hampshire GU34 3AQ. Tel: +44 (0)1420 89007 Fax +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
-
Page 9: Notice De Montage
CP0478 PAGE 9 OF 13 Photo 1 Photo 2 NOTICE DE MONTAGE Côté gauche (lorsqu’on est assis sur la moto) • Avant d'installer les protections R&G, il est conseillé de placer un cric sous la moto à un endroit approprié pour supporter le poids du moteur pendant le montage. Un petit morceau de bois doit également être placé... - Page 10 PAGE 10 OF 13 CP0478 MONTAGEANLEITUNG FÜR CP0478 STURZPADS TRIUMPH SCRAMBLER 1200 2019- LLE KIT TEILE SIND UNTEN ABGEBILDET UND GEKENNZEICHNET IE ABGEBILDETEN EILE DIENEN LEDIGLICH ZUR RKLÄRUNG Ü BERPRÜFEN SIE DASS ALLE TEILE VORHANDEN SIND BEVOR SIE MIT DER...
- Page 11 CP0478 PAGE 11 OF 13 SIE BENÖTIGEN FOLGENDES WERKEZEUG: ALLGEM. ANZUGSDREHMOMENT • M4 SCHRAUBE = 8Nm 30 & 55 TORX-SCHLÜSSEL M5 SCHRAUBE = • SATZ STECKSCHLÜSSEL INKL. 17mm STECKSCHLÜSSEL M6 SCHRAUBE = MIT VERLÄNGERUNG M8 SCHRAUBE = 20Nm • 17MM SCHRAUBENSCHLÜSSEL...
- Page 12 PAGE 12 OF 13 CP0478 ZUSAMMENBAU ZEICHNUNG 1—LINKE SEITE ZUSAMMENBAU ZEICHNUNG 1—RECHTE SEITE R&G Racing Unit 1, Shelleys Lane, East Worldham, Alton, Hampshire GU34 3AQ. Tel: +44 (0)1420 89007 Fax +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
- Page 13 CP0478 PAGE 13 OF 13 Abbildung 1 Abbildung 2 MONTAGEANLEITUNG Linke Seite (in Fahrtrichtung) • Bevor Sie die R&G Sturzpads montieren, empfehlen wir, einen Scherenheber an einem geeigneten Montagepunkt unter das Motorrad zu stellen, um somit das Gewicht des Motors während der Montage zu stützen. Ein kleines Stück Holz sollte zusätzlich zwischen Montagepunkt und Heber platziert werden, um die Last zu verteilen.
Need help?
Do you have a question about the CP0478 and is the answer not in the manual?
Questions and answers