Advertisement
Quick Links
Tone Handcrank and Extended Handcrank
Note that these instruc ons show generic parts. Parts included in individual tables may differ in appearance and func onality
but the assembly principle is the same.
Cau on: No impact drivers or other high‐torque equipment are to be used!
Complete product without work surface
Housing
Side Bar
Column
Complete product with work surface
ASSEMBLY INSTRUCTIONS
Gearbox
Worm Gear
Drive Sha
Crossbar
Crank Handle
Catch
Crank Handle
Foot
Crank
Arm
1
90⁰
120⁰
90⁰
120⁰
07.17
Advertisement
Related Manuals for Knoll Tone Handcrank
Summary of Contents for Knoll Tone Handcrank
- Page 1 07.17 ASSEMBLY INSTRUCTIONS Tone Handcrank and Extended Handcrank Note that these instruc ons show generic parts. Parts included in individual tables may differ in appearance and func onality but the assembly principle is the same. Cau on: No impact drivers or other high‐torque equipment are to be used! Complete product without work surface Gearbox ...
- Page 2 07.17 ASSEMBLY INSTRUCTIONS KR68003496 Feet Type (Fig. 1) Feet Screw Socket Round UNC 5/16‐18x5/8” Zn On‐Foot / OnC (for 2‐stage columns) · Maximum Torque from 3 to 5 lbf . On‐Foot / OffC (for 2‐stage columns) In‐Foot / OnC (for 3‐stage columns) In‐Foot / OffC (for 3‐stage columns) See page 15 for assembly instruc ons. Crossbar Type (Fig. 2) Crossbars Adjustable width Fixed width For 120 and 90° Holes used for moun ng of Loosen screws to adjust crossbar length crossbars on the long side ...
- Page 3 07.17 ASSEMBLY INSTRUCTIONS (Fig. 3) Sidebars Sidebar Type KR79100036 Screw Philips Undercut Flathead 1/4 ‐20x5/8” Zn Symmetric Sidebar for T‐leg Part number: KR3AE4015 Right Hand / Le Hand sidebars for C‐leg Part numbers: KR3AE4014L ‐ Le KR3AE4014R ‐ Right (Fig. 4) Bumpers KR68003468 Bumper 1/2"x1/2"x1/4" Transparent KR68003467 Bumper Ø1/2"x1/8" ...
- Page 4 07.17 ASSEMBLY INSTRUCTIONS (Fig. 5) 3‐Column 90⁰ Adjustable Crossbars Adjustable crossbars for 3‐column 90⁰ table. 3 regular adjustable crossbars 1 special adjustable crossbar Special adjustable crossbar Alterna ve foot KR68003491 No addi onal assembly kit Screw Socket CSK UNC 5/16‐18x1‐1/2" Zn (Fig. 6) 3‐Column 90⁰ Fixed Crossbars Regular fixed crossbar Regular fixed crossbar Regular fixed crossbar Fixed crossbars for 3‐column 90⁰ table. 6" shorter than the ...
- Page 5 07.17 ASSEMBLY INSTRUCTIONS (Fig. 7) 3‐Column 120⁰ Adjustable Crossbars Adjustable crossbars for 3‐column 120⁰ table. 4 regular adjustable crossbars KR68005205 Hex Nut UNC 5/16‐18 Zn 2 Brackets KR68005095 Bracket 120⁰ Outer KR68003490 KR68005096 Bracket 120⁰ Inner Screw Socket CSK UNC 5/16‐18x1" Zn (Fig. 8) 3‐Column 120⁰ Fixed Crossbars Fixed crossbars for 3‐column 120⁰ table. 4 regular fixed crossbars KR68005205 ...
- Page 6 07.17 ASSEMBLY INSTRUCTIONS (Fig. 8) Moun ng of gears and drive sha s 1. Fit Gearbox with correct side facing up (see pages 10‐12) on actuator sha . 4 2. Insert plas c slide bearing into drive sha hole of plas c adapter fi ed in 2 housing. 3. Insert hex rod with grooves through plas c adapter, slide bearing and gearbox. NOTE: Make sure hex rod is pushed all the way into the gearbox. Groove should become visible. 4. Snap retaining washer into groove in hex rod to lock assembly in place. 5. Push worm gear (from crank arm 5 ...
- Page 7 07.17 ASSEMBLY INSTRUCTIONS (Fig. 9) Moun ng of gears and drive sha s Drive sha alterna ve with two aluminum tubes. KR68004171 KR68004172 KR68004173 Drive sha alterna ve with one aluminum tube. KR68004170 When one aluminum tube is used, push O‐ring toward outside edges to fix aluminum tube in place. When two aluminum tubes are used, push tubes as far as possible toward housings. Push O‐rings toward inside edges to fix aluminum tubes in place 7 ...
- Page 8 07.17 ASSEMBLY INSTRUCTIONS (Fig. 10 a) Assembly of crank arm U bracket Crank arm handle Hex rod Worm gear Small locking rings Aluminum tube Large locking ring (Fig. 10 b) The worm gear should be inserted on the hex rod prior to moun ng the drive sha s. Locate the worm gear next to the housing at desired column. It does not need to be fastened. (Fig. 10 c) Insert hex rod (included in crank arm assembly) into the worm gear with one small locking ring on each side. Do not ghten the locking rings at this point. (Fig. 10 d) A ach the large locking ring on the ...
- Page 9 07.17 ASSEMBLY INSTRUCTIONS (Fig. 10 e) 3 3/4” Mount the aluminum tube onto the hex rod. A ach the U bracket with wood screws underneath the work surface 3¾” from the work surface edge. 3 3/4” (Fig. 10 f) With the U bracket fixed in place, push the crank arm handle against the angle. Then push the hex rod as far as it goes into the aluminum tube. Lock the small locking rings ght with Allen key. (Fig. 10 g) Fix crank handle catch in work surface according to image to support the handle. Crank Handle Catch 9 ...
-
Page 10: Supplementary Information
07.17 ASSEMBLY INSTRUCTIONS SUPPLEMENTARY INFORMATION Gearbox Placement Three different gear boxes are used: The Gearbox AC has one drive sha outlet. The two sides are named A & C. The ver cal rota on is reversed when the gearbox is turned upside down. The A‐side is the side with screws. The C‐ side is the side without screws. 2‐column tables only use Gearbox AC The Gearbox BD has two drive sha outlets placed in 90°. The two sides are named B & D. The ver cal rota on is reversed when the gearbox is turned ... - Page 11 07.17 ASSEMBLY INSTRUCTIONS Worm Gear The worm gear is placed on the side of the table where the crank handle should be. It is placed on the hex bar that is a ached to the Gearbox. The worm gear should be placed immediately outside the housing. It does not need to be fastened. The worm gear can be placed either way UP on the hex bar. The ac on remains the same. Worm gear must be oriented upward as shown. 2‐Column Table Crank arm on the le side Normally, the ac on of the crank arm should operate in the following manner: turn = table going DOWN turn = table going To achieve this on a 2‐column table the Gearbox must be placed with the A‐side facing up on the right column and the C‐ side facing up on the le column. The crank arm can then be placed on Crank arm on the right side preferred side of the table (right or le ). 11 ...
- Page 12 07.17 ASSEMBLY INSTRUCTIONS 3‐Column Table 90° Normally, the ac on of the crank arm should operate in the following manner: turn = table going DOWN turn = table going On a 3‐column table every other Gearbox must be placed with the ”opposite” side up. That is, every other gear must have the side with the screws facing up. This means that the gears on both outer column will be facing the same way. As a gear with two drive sha outlets is needed on the middle column, the Gearbox BD must be used here. As opposed to a 2‐column table, the side on which the crank arm is placed has importance on a 3‐column table. The correct placement is as follows: Crank arm on the le side = CBC Crank arm on the right side = ADA 3‐Column Table 120° Same principle as for a 3‐column 90° table apply also for a 3‐column 120° table. ...
- Page 13 07.17 ASSEMBLY INSTRUCTIONS Drive Sha Kits Part Number Descrip on 2‐Column 3‐Column 90⁰ 3‐Column 120⁰ Work surface width 42 48 54 60 66 72 78 48 54 60 48 54 60 KR68004170 Drive Sha Kit c/c 26"‐40" / OH 31"‐45" KR68004171 Drive Sha Kit c/c 38"‐64" / OH 43"‐69" ...
- Page 14 07.17 ASSEMBLY INSTRUCTIONS Crank Arm Kits 24" C‐Leg 30" C‐Leg 30" T‐Leg 68004148 Crank Arm Kit 14"‐18" 68004149 Crank Arm Kit 15"‐24" X Crank Arm Kit 68004148 X = 14”‐18” Crank Arm Kit 68004149 X = 15”‐24” User Manual Tone Handcrank and Extended Handcrank User manual should be le on the table a er completed installa on. 14 ...
-
Page 15: Assembly Procedure
07.17 ASSEMBLY INSTRUCTIONS ASSEMBLY PROCEDURE Fig. 1 FEET Assemble the feet on the columns. · Tighten screws firmly. Maximum Torque from 3 to 5 lbf . IMPORTANT: Make sure the correct screws are used. Using too long screws may destroy internal parts in the column. Fig. 2 CROSSBARS A ach the crossbars on the long side of the housings. Tighten screws firmly. ... - Page 16 JONLAR Rev D 2016‐04‐12 90 deg crank arm angle replaced with U bracket. LINPHA See rev. C 68004148 and 68004149. Knoll Z Crank Handle Catch added Text modified a er Knoll input Revised wood screws in Fig. 4, Page 15 Revised screw types in Fig. 1, 2, 5, 6, 7 & 8 Reworded bumper instruc ons in Fig. 4, Page 15 Drawings updated to show crank arm catch on le side of crank Revised all drawings on Page 1, and Figs 10f & 10g on Page 9 Removed middle column drawings on page 6. ...
Need help?
Do you have a question about the Tone Handcrank and is the answer not in the manual?
Questions and answers