Heta SCAN-LINE 500 Series Operating And Installation Instructions
  1. Manuals
  2. Brands
  3. Heta Manuals
  4. Stove
  5. Scan-line 500 Series
  6. Operating and installation instructions

Heta SCAN-LINE 500 Series Operating And Installation Instructions

Hide thumbs Also See for SCAN-LINE 500 Series:
Table of Contents

Advertisement

Quick Links

Download this manual
oPeratinG anD installation
instrUCtions
sCan-line 500 series
Scan-line 500 serie SCA is exempt for use in smoke
control areas when burning dry wood
eCoDesiGn reaDy
www.heta.dk
en
Danish DesiGn . Danish QUality . Danish ProDUCtion
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SCAN-LINE 500 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Heta SCAN-LINE 500 Series

Summary of Contents for Heta SCAN-LINE 500 Series

  • Page 1 500 series Scan-line 500 serie SCA is exempt for use in smoke control areas when burning dry wood eCoDesiGn reaDy www.heta.dk Danish DesiGn . Danish QUality . Danish ProDUCtion...

  • Page 2: Table Of Contents

    Heta stove. Especially if you follow the following advice and instructions. Scan-Line 500 series have been approved according to the EN 13240: 2005 / A2: 2004 / NS 3058, and the Scan-Line 500 SCA series are modified so that they are also recommended as exempt for use within smoke control areas (SCA) throughout the UK (see clean air act Appendix A).

  • Page 3: Before Installation

    It is important that upon receipt check your Heta product completely and report any damage or defects to your dealer. The packaging must be disposed of as follows: Wood is untreated and able to burn in the stove.
  • Page 4 With your new wood stove you should find the following: Operating / Q.C. check Instruction manual Heta glove Data plate 0023-9002 Tool set required tools are not supplied. Scan-Line 510 Accessory Tool set Scan-Line 500, 520, 550, 551, 560, 590.

  • Page 5: Before Installation

    1. oPeratinG instrUCtions 1.1 Before using ting fire starter (bag, brick, paraffin) on the top, now you are ready to light the fuel. The flames Before the wood stove is used make sure re- must work from the top down. quired installation conditions, are met.

  • Page 6: Emptying The Ash

    much, it may be necessary to have the door ajar. The wood will then ignite within a very short time (Typically 1 to 3 minutes). Once the fuel is Ignited. Close the door and regulate the air back to ope- rating air.

  • Page 7: Draft Conditions In The Chimney

    Good draft will allow the stove to achieve op- timal combustion and the highest possible ef- ficiency. Heta wood stoves are constructed so that it itself provides an optimal blend of com- bustion air. This provides a high efficiency/heat, clean glass and low environmental impact.

  • Page 8: Operating Problems

    1.11 operational problems Correct firing using well seasoned wood pro- vides optimal heat output and maximum effi- The chimney must be swept at least once a ciency. At the same time, correct firing prevents year, we recommend the use of a NACS (natio- environmental damage in the form of smoke nal association of chimney sweeps) registered emissions and reduces the risk of chimney fires.

  • Page 9: Cleaning The Glass

    Where necessary, use vered in soot. an aluminium tray or a Heta roasting tin no. (no. 0050-0304) to catch any spills. This can be removed easily and effectively using glass...

  • Page 10: Troubleshooting Table

    1.17 troubleshooting table - applies to all stove types Fault Cause Troubleshooting Solution Inadequate chimney draft. Lighting problems. When the You can test using a lighter whether Improve the chimney. The chimney only has stove is cold, smoke seeps flame is drawn into the combustion sufficient draft when it is hot.

  • Page 11: Stove Data Table En 13240

    Therefore, the duration of the warranty is 5 years on this product, covering manufactu- rer’s defects, 1 year on paint adhesion defects from purchase date from Heta and a 3 months total warranty for seals, vermiculite and glass from the date of sale from the dealer.

  • Page 12: Cleaning After Sweeping Or Before Replacing Vermiculite Stones

    1.20 scan-line 500-550. Cleaning after sweeping or before replacing vermiculite stones Note: it may be necessary to clean/vaccum the holes and air ducts behind the rear stone. Order of removing Fire bricks. Scan-Line 500 Scan-Line 550 Replace in reverse order. Starting with fig.

  • Page 13: Parts

    1.21 Parts - scan-line 500 - inside fire chamber Pos. No. Name 1 0023-0075 Upper baffle 2 0023-0076 Right side stone 3 0023-0077 Left side stone 4 0023-0078 Back stone 5 1500-022221 Log retainer 6 0015-2013 Knob 7 1021-4062 Shake pin 8 0030-0201 Grate 9 0030-0013...
  • Page 14 Parts - scan-line 550 - inside fire chamber Pos. No. Name 0023-0092 Upper baffle 0023-0076 Right side stone 0023-0077 Left side stone 0023-0078 Back stone 1019-0020 Log retainer 1019-0019 Inlet 0030-0013 Casted bottom 0015-1024 Knob 1021-0066 Shake pin 0030-0201 Grate Parts - scan-line 550 - stove door Pos.
  • Page 15 Parts - scan-line 500 Baking oven door Pos. Name Qty. 0008-0262041 Screw M4x6 0008-2005 Screw M5x10 0016-0047 Handle 0021-0022 Glass 0023-3010 Textile glass 6 mm with adhesive, black L=1.1 m 1013-0432 Glass clips 2005-0004 Baking oven door Parts - scan-line 550 Baking oven door Pos.

  • Page 16: Installation Instructions

    Secretary of State in accor- dance with changes made to sections 20 and The Scan-Line 500 series with and without side 21 of the Clean Air Act 1993 by section 15 of windows have all been recommended as suita- the Deregulation Act 2015.

  • Page 17: Installation Instructions

    / or chimney. beading. Heta A/S stresses that it is of utmost In front of the fireplace insert, the substrate importance that this is done correctly with very must consist of non-combustible material, for tight joints.

  • Page 18: Combustion Air And Ventilation

    The Scan-Line 500 series has a nominal output Combustion air and Ventilation of less than 5 kW and does not need additional...
  • Page 19 scan-line 500 stone ø100 scan-line 510 ø100 Casted top Stone top 1190 1200...
  • Page 20 scan-line 510 stone ø100 scan-line 520B ø100 Casted top Stone top 1190 1200...
  • Page 21 scan-line 520B stone ø100 scan-line 520W ø100 Casted top Stone top 1190 1200...
  • Page 22 scan-line 520W stone ø100 scan-line 550 ø100...
  • Page 23 scan-line 551 ø100 scan-line 560B ø100...
  • Page 24 scan-line 560s ø100 scan-line 590 ø100 Casted top Stone top 1285 1295...

  • Page 25: Changing To A Back Flue Outlet

    ø100 mm, the draught in the flue Air intake depends on this air for optimal combustion. ø100 Heta recommends max. 4 meters of direct air pipe, with max. 3, 90° bends and a min. of ø100 mm. Flexi pipe back outlet...

  • Page 26: Clearances For Installation

    2.8 Clearances for installation en 13 240 Clearances for installation Stove Distance to flamable materials scan-line 500 serien Minimum rear the at the at fur- dimensions stove sides nitures Scan-Line 500 1000 1000 520 + 520B 1000 1000 1000 560S + 560B 1000 Combustible 1000...

  • Page 27: Eu Declaration Of Conformity

    Certifikat no. 2354 Manufacturer Heta A/S Ecodesign Adress Jupitervej 22, DK 7620 Lemvig EU Declaration of Conformity E-mail heta@heta.dk Website www.heta.dk DoC Scan-Line 500 2354-2018 Telephone +45 9663 0600 Product fiche Model identifier Scan-Line 500, 510, 520, 520B, 550, 551, 560B, 560S, 590, Turin, Turin B, Napoli, 10-20-20B-30-30B, Tour...

This manual is also suitable for:

Scan-line 500Scan-line 510Scan-line 520bScan-line 520wScan-line 550Scan-line 551 ... Show all

Table of Contents