Advertisement
Advertisement
Table of Contents
Related Manuals for Patriot Lighting 355-6703
Summary of Contents for Patriot Lighting 355-6703
- Page 1 355-6703 Model No.: # PAGE: 1 / 11 220104...
-
Page 2: Package Contents
Package Contents: Accent Main REMOTE CONTROL Unpack your fan and check the contents. You should have the following items. 1.) Hanger Bracket 2.) Canopy 3.) Decorative Cap (Comes in a Separate Bag) 4.) Downrod Stand Cover 5.) Downrod Set (Included Hanger Ball, 6” Downrod, Hanger Pin & Lock Pin) 6.) Fan Motor Assembly 7.) Fan Blades (3PCS) 8.) Blade Holder (3PCS) - Page 3 Exploded View Detail Hanger Bracket Hanger Ball Downrod Canopy Decorative Cap Downrod Stand Cover Hanger Pin Lock Pin Collar Housing Blade Holder Blade Switch Box Switch Box Screw Fan Light Dual Mount Drawing Downrod Mount Sloped Ceiling Mount (Up to 23 degrees) PAGE: 3 / 11 220104...
-
Page 4: Safety Instructions
Safety Instructions READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN TO INSTALL THE FAN AND SAVE INSTRUCTIONS. All set screws of the fan must be checked and retightened where necessary before installation. To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades or cleaning the fan. -
Page 5: Installation Instructions
INSTALLATION INSTRUCTIONS IMPORTANT: BEFORE YOU BEGIN INSTALLING THE FAN, CAREFULLY READ ALL INFORMATION IN THE SAFETY INSTRUCTIONS AND INSTALLATION INSTRUCTIONS. IF IN DOUBT, CONSULT A QUALIFIED ELECTRICIAN. SAVE ALL INSTRUCTIONS. NOTE: The fan weight is 17.28 lbs (7.84 kgs). Be sure the outlet box you are using is securely attached to the building structure and can support the full weight of the fan. - Page 6 Transmitter Both the transmitter and receiver have a 4-key unit code on each DIP Switch (Fig.8) and by default, all keys are pre-set to the "off" position. This means that the transmitter and receiver are already paired together. However, if you have multiple fans and remote controls and want to DIP Switch Receiver...
- Page 7 Loose canopy screw and do not Fig.11 Fig.12a remove it, push the canopy upwards to cover hanger bracket by Motor inserting canopy screw into key Hanger Bracket hole slot, then rotate the canopy till it Canopy Screw fixed on the hanger bracket. Finally, Blade Holder Attach the decorative cap to canopy, Screw...
- Page 8 1. Install the battery (9V) into the transmitter. Fig.16 2. OPERATING TRANSMITTER: * Press "HI" to turn on the fan at high speed. * Press "MED" button to turn the fan in medium speed. * Press "LOW" button to turn the fan in low speed. ACCENT * Press "OFF"...
- Page 9 For a single switch Follow these steps: Connect the white (neutral) wire from motor to the white (neutral) wire from the outlet box with a wire White connector. Connect three ground wires (Green Connect the black (hot) wire or bare copper) coming Black (This is for fan control),orange from outlet box,...
-
Page 10: Troubleshooting Guide
Troubleshooting Guide If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation or wiring. If you experience any faults, please check this Troubleshooting Guide. If a problem cannot be remedied or you are experiencing difficulty in installation, please call our Customer Service Department (1-800-887-6326). - Page 11 DYNAMIC BLADE BALANCING KIT YARDSTICK BALANCING WEIGHT CENTERLINE MEASURING POINT COUNTER- CLOCKWISE PLASTIC CLIP PREFACE Your ceiling fan may sometimes have wobbling problems when operating due to irregularity in the blades or the blade brackets. Improper assembly in the mounting system may cause some additional problems.
Need help?
Do you have a question about the 355-6703 and is the answer not in the manual?
Questions and answers