Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Patriot Lighting SWANK 37591-MNDC
Summary of Contents for Patriot Lighting SWANK 37591-MNDC
- Page 1 Sku Number: 355-0718 16" SWANK FLUSH-MOUNT CEILING FAN Model Number: 37591-MNDC Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-833-695-2045, 8:30 a.m. - 5 p.m., EST, Monday - Friday.
- Page 2 SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate, or install the product. All set screws must be checked and retightened where necessary before installation. To reduce the risk of personal injury, do not bend the blade brackets when installing, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
- Page 3 The limited lifetime warranty covers this Ceiling Fan, for residential use by the original purchaser, against defects in material or workmanship as follows: If your Patriot Lighting Ceiling Fan motor fails at any time during the lifetime of the original purchaser due to defects in material or workmanship, we will provide a replacement part free of charge.
- Page 4 PRE-INSTALLATION PREPARATION To avoid damaging the product, assemble it on a soft, non-abrasive surface, such as carpet or cardboard. Inspect each part for defects such as the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the wire, do not continue the assembly process.
- Page 5 ASSEMBLY INSTRUCTIONS WARNING: Turn off the power at fuse or circuit box. To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked "Acceptable for fan support of 14.5 kg (32 lbs) or less", and use mounting screws provided in assembly kit. 1.The hanging board is dismounted from the lamp body.
- Page 6 TRANSMITTER SPECIFICATION 7.Remove the transmitter battery back cover. 8.Install two AAA batteries, fig 1. 9.Install the battery rear cover. Fig 1 Transmitter decoding operation: Transmitter Turn on the power to turn the light on. Press the Stop (10) button within 5 seconds, after you hear the "beep"...
- Page 7 6.light temperature + Repeat for each blade. Any measurement deviation should be within 1/8 in. Run the fan for ten minutes. If the fan continues to wobble please contact Patriot Lighting Customer Service and a 7.light temperature - balancing kit will be sent to you at no charge.
Need help?
Do you have a question about the SWANK 37591-MNDC and is the answer not in the manual?
Questions and answers
I have a patriot lighting swank 16 in indoor intergrated led fandelier fan . The lights work like they should but the fan stays on and will not shut off or change speeds or rotate. You you give me some things to check solve this problem. Have had fan about e months
To troubleshoot a Patriot Lighting Swank 37591-MNDC fan that stays on and does not change speeds or rotate, follow these steps:
1. Check the main and branch circuit fuses or breakers.
2. Check the line wire connections to the fan and the switch wire connections in the switch housing.
3. Check the battery in the remote control.
4. Make sure you are within the 10–20 feet range for the remote to work.
5. Turn off the power and verify that dip switch settings on the remote and receiver match.
6. Ensure all motor housing screws are tight.
7. Check that the screws attaching the fan blade brackets to the motor hub are secure.
This answer is automatically generated
Why won't my remote work with my light? The light turns on from the switch. The remote will not control the fan, or lights. There is a blue light on the remote when pressed. Tried a reset with the remote and it turn light on and off one time and nothing after that. Do I need a new remote? There are no dip switches on the remote as stated in manual requesting they are set the same!! Thank you, Brenda
The light stays on but the fan doesn’t work, not do the other functions on the remote work
My fan works , but I have no light?
I need a replace.ent remote