Table of Contents
Advertisement
Quick Links
IM-A-909B November 2017
INSTRUCTION MANUAL
CDV-44AS
For EDX-100A/EDX-2000A/EDX-3000A
STRAIN/VOLTAGE MEASUREMENT INSULATION CARD
Thank you for purchasing KYOWA's product CDV-44AS Strain/Voltage Measurement Insulation Card.
Read this Instruction Manual carefully in order to make full use of the high performance capabilities of the
product.
Do not use the product in methods other than described in this Manual.
This Instruction Manual may not be copied or reproduced, in whole or part, without consent of KYOWA.
Copyright © Kyowa Electronic Instruments Co., Ltd. All rights reserved.
The contents of the Instruction Manual are subjected to change without prior notice.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for KYOWA CDV-44AS
Summary of Contents for KYOWA CDV-44AS
- Page 1 Do not use the product in methods other than described in this Manual. This Instruction Manual may not be copied or reproduced, in whole or part, without consent of KYOWA. Copyright © Kyowa Electronic Instruments Co., Ltd. All rights reserved.
-
Page 2: Table Of Contents
SAFETY SYMBOLS ....................2 NOTATIONS USED IN THE INSTRUCTION MANUAL............3 INFORMATIONAL NOTES ................... 3 OUTLINE OF PRODUCT ..................4 1.1 OUTLINE OF CDV-44AS ..................4 1.2 PARTS NAMES & FUNCTIONS................5 1.3 PIN ASSIGNMENT ..................... 6 1.4 INSTALLATION OF CDV-44AS ................7 1.5 CONNECTION METHOD.................. -
Page 3: Standard Accessories
This Manual describes the CDV-44AS Strain/Voltage Measurement Insulation Card (hereinafter referred to as the CDV-44AS). STANDARD ACCESSORIES The following accessories are packed with the CDV-44AS. When unpacking, check the contents to ensure that all accessories are enclosed. Voltage Conversion Adapter (FV-2A) ····················· 1 Warranty and Test Data Sheet ·······························... -
Page 4: Safety Precautions
(Do not forget to read the safety precautions prior to use.） The CDV-44AS is designed to be used according to "3. SPECIFICATIONS." Do not use the CDV-44AS in an environment exceeding the range of the above specifications of the EDX-100A/EDX-2000A/EDX-3000A. Or, system failure may result in. -
Page 5: Notations Used In The Instruction Manual
NOTATIONS USED IN THE INSTRUCTION MANUAL INFORMATIONAL NOTES Certain notations are used as necessary to attract your attention to information that requires special care when handing the CDV-44AS, and to information provided for reference purposes. Examples of Notations NOTE Describes essential instructions when handling the CDV-44AS. -
Page 6: Outline Of Product
1 OUTLINE OF PRODUCT 1.1 OUTLINE OF CDV-44AS ・ The CDV-44AS is a signal conditioner card for a strain gage, strain gage transducer, and voltage output type sensor. ・ The CDV-44AS is isolated between input and case (output) as well as between channels. -
Page 7: Parts Names & Functions
1.2 PARTS NAMES & FUNCTIONS (1) Input connector 1 Input connector of the 1st channel (2) Input connector 2 Input connector of the 2nd channel (3) Input connector 3 Input connector of the 3rd channel (4) Input connector 4 Input connector of the 4th channel (5) Monitor output Connector Monitor output connector Monitor voltage is ±5V with full scale of each range. -
Page 8: Pin Assignment
+ Bridge Excitation Voltage - Input - Bridge Excitation Voltage + Input ACOM ID signal + Channel No. of the input connector shall be as follows according to slot into which the CDV-44AS is installed in the EDX-100A/EDX-2000A/EDX-3000A. Slot Input connector CH17 CH25... -
Page 9: Installation Of Cdv-44As
After inserting the CDV-44AS, turn ON the power switch and confirm the startup screen by referring the "DCS-100A Instruction Manual for EDX-100A." If the "Card Type" is displayed in the Slot No. -
Page 10: Connection Method
When one end of the strain gage transducer is equipped with no plug, there are 2 ways for connecting the strain gage transducer to the CDV-44AS. One is to connect conductors to a plug in advance and the other is to connect by using a bridge box. How to connect conductors is described in the following figure. - Page 11 NOTE ● The F terminal of each channel input for the CDV-44AS is intended for sensor ID signals. Connecting any other signal to this terminal may prevent the EDX-100A/EDX-2000A/EDX-3000A from recognizing all conditioners installed in the system. If the EDX-100A/EDX-2000A/EDX-3000A does not recognize the conditioners, the startup screen will display "UNKNOWN"...
- Page 12 0 V. b) When connecting an input, correctly connect the positive and negative sides. c) Maximum input voltage of the CDV-44AS is ±50 V. Do not apply an input voltage exceeding that range. ● Use the attached voltage conversion adapter (FV-2A).
- Page 13 When connecting an U-03 (optional) to an input connector Description of the optional cable (U-03) ＋ White － Blue Ｇ Black Ｅ CDV-44AS Ａ ＋ Ｂ Ａ Ｆ White Ｇ Ｃ － Ｂ Ｅ Ｄ Ｃ Ｄ Blue Ｅ...
- Page 14 Ｅ NOTE The CDV-44AS is isolated between the E terminal of the monitor output and E terminal (ACOM) of every input channel. In addition, the E terminal of the monitor output and G terminal (FG) of every input channel is connected.
-
Page 15: How To Set The Cdv-44As
・ For installing the CDV-44AS to the EDX-100A, refer to "DCS-100A Instruction Manual for EDX-100A operation." ・ For installing the CDV-44AS to the EDX-2000A or EDX-3000A, refer to separate volumes of "Instruction Manual for Hardware" and "Instruction Manual for Software."... -
Page 16: Specifications
3 SPECIFICATIONS 3.1 HARDWARE SPECIFICATIONS Name Strain/Voltage Measurement Insulation Card Applicable Sensors Strain Gage, Strain Gage Transducer, Voltage The Number of Input Channels Input Mode Balanced differential (strain mode) Unbalanced (voltage mode) Input resistance Approx. 10Ｍ ohm＋10M ohm (strain mode) Approx. -
Page 17: External Views
3.2 EXTERNAL VIEWS - 15 -... -
Page 18: Optional Accessories
4 OPTIONAL ACCESSORIES Optional accessories are as follows. a) Input cable (U-03) By connecting to an input connector, this input cable is capable of inputting voltage in noisy conditions. For details, see “1.3 PIN ASSIGNMENT.” ＋ White － Blue Ｇ Black Ｅ...
Need help?
Do you have a question about the CDV-44AS and is the answer not in the manual?
Questions and answers