Do you have a question about the NER E10s and is the answer not in the manual?
Questions and answers
Ilene
March 28, 2025
Mop pad so t stay on
1 comments:
Mr. Anderson
May 14, 2025
To ensure the mop pad stays on the Eureka NER E10s, make sure it is properly attached according to the device’s instructions. If the brushes or pads come off easily, some users have reported needing to secure them more firmly, such as using glue. However, modifying the device may void the warranty.
This answer is automatically generated
Ilene
March 28, 2025
How to put the mop pad on
1 comments:
Mr. Anderson
March 28, 2025
To attach the mop pad to the Eureka NER E10s:
1. Remove the mop assembly from the robot. 2. Detach the mopping cloth from the mop holder. 3. Wash and dry the mopping cloth. 4. Place the cleaned mopping cloth back onto the mop holder. 5. Reinstall the mop assembly onto the robotic vacuum.
Page 1
NER E10s Robotic vacuum; household type Owner’s Guide Thank you for purchasing your new Eureka vacuum! Important instructions For easy assembly, please take a few moments to read this owner’s guide. If you have questions about your new vacuum, please contact our customer service HELPLINE at 1-800-282-2886.
fireplace. the Eureka Customer Service HELP- • Do not allow children to sit on LINE at 1-800-282-2886. vacuum. • To avoid excessive heat and damage •...
Page 5
Exposure to fire or • If a cell or a battery has leaked or temperature above 266°F may cause vented, it should be replaced explosion. • Follow all charging instructions and www.eureka.com...
Page 6
REMOVE MAIN BRUSH BEFORE • Docking station is only for use with CLEANING OR SERVICING. the Eureka NER E10s robotic vacuum. • Warning: The battery charger (Docking station) is not intended to charge non-rechargeable batteries. Eureka Customer Service HELPLINE 1-800-282-2886...
Page 7
X is the symbol for the time/current characteristic as given in IEC 60127 [symbol IEC 60417-5032 alternating current ( 2002-10 )] [symbol IEC 60417-5172 class II equipment ( 2003-02 )] SAVE THESE INSTRUCTIONS Household use only www.eureka.com...
- Consult the dealer or an experienced radio/TV technician for help. To satisfy FCC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. Eureka Customer Service HELPLINE 1-800-282-2886...
Parts and Components What comes in the box Robotic Vacuum Self-Emptying Base 445mm 97mm Side Brush x2 Cleaning Brush Instruction Manual Eureka Customer Service HELPLINE 1-800-282-2886...
Release Button of Water Tank Auto-lifting Mop Cli Sensors Omni-directional Wheel Carpet Detection Sensor Side Brush Main Brush Auto-lifting Mop Assembly Main Wheel Cover Plate of Main Brush Charging Contacts Dust Cup Power Cable Slot Power Switch Charging Self-empty Contacts Inlet www.eureka.com...
Store the excess cords into the slot at the back of the charging base to avoid a ecting the proper function of the robotic vacuum. Plug the power cord into a power outlet. Switch the power switch to “I” position to turn on the base. Eureka Customer Service HELPLINE 1-800-282-2886...
Page 13
3 months, allow it to get charged for at least 12 hours before using. To preserve the battery lifespan, we suggest you fully charge the battery at least once every six months. www.eureka.com...
Self-emptying base is powered on. White light flashes slowly Self-emptying is in progress. The air duct of the dust cup may be clogged. White light flashes quickly Please check and empty the dust cup in time. Eureka Customer Service HELPLINE 1-800-282-2886...
Using Eureka Robot App NOTE: If the wireless network in your home is unstable, it may cause issues with the operation of the Eureka Robot App. The content of the Eureka Robot App may change when the version is updated. Please refer to the Eureka Robotic Vacuum interface for details.
Wash the mopping cloth with water and dry it. Push/Pull Slot Remove the mopping cloth from Place the cleaned mopping cloth the mop holder. back to the mop holder and re-install the mop assembly to the robotic vacuum. Eureka Customer Service HELPLINE 1-800-282-2886...
Washable brushroll – clean frequently CAUTION Make sure robotic vacuum is turned o and not plugged into a power source. Do not attempt to remove belt. Call the Eureka Customer Service HELPLINE at 1-800-282-2886. Cleaning tools How to use the cleaning brush: ①...
Page 18
Rinse the cyclone with clean water and make sure it is completely dry before putting it back. Note: Do not use detergents, polishes or air fresheners to clean the dust cup and cyclone to avoid corrosion. Eureka Customer Service HELPLINE 1-800-282-2886...
Page 19
Sensors and charging contacts cleaning Wipe the sensors on the robotic vacuum and charging contacts on both the robotic vacuum and the base with a dry, soft cloth. www.eureka.com...
Eureka authorized resellers. Eureka will, at its option, repair or replace a defective vacuum or vacuum part that is covered by this warranty. Repairs may be performed using new Eureka will, at its option, repair or replace a defective Battery Module or or refurbished parts that meet or exceed Eureka specifications for new...
Remove the obstacle ahead. Gently tap the front bumper to The bumper is stuck. remove dust. The robotic vacuum moves backward There is dust accumulated on Clean the dust accumulated on the cli sensors. the surface of cli sensors. www.eureka.com...
This product contains a lithium-ion battery. It must be disposed of properly. Local laws may prohibit disposal of lithium-ion batteries in ordinary trash. Consult your local waste authority for information regarding available recycling and/or disposal options. Eureka Customer Service HELPLINE 1-800-282-2886...
Need help?
Do you have a question about the NER E10s and is the answer not in the manual?
Questions and answers
Mop pad so t stay on
To ensure the mop pad stays on the Eureka NER E10s, make sure it is properly attached according to the device’s instructions. If the brushes or pads come off easily, some users have reported needing to secure them more firmly, such as using glue. However, modifying the device may void the warranty.
This answer is automatically generated
How to put the mop pad on
To attach the mop pad to the Eureka NER E10s:
1. Remove the mop assembly from the robot.
2. Detach the mopping cloth from the mop holder.
3. Wash and dry the mopping cloth.
4. Place the cleaned mopping cloth back onto the mop holder.
5. Reinstall the mop assembly onto the robotic vacuum.
This answer is automatically generated
How much water to use to fill the mop tank