Glentronics PRO Series Instruction Manual & Safety Warnings
Combination primary and backup sump pump system
Hide thumbs
Also See for PRO Series:
- Instruction manual & safety warnings (16 pages) ,
- Instruction manual (12 pages) ,
- Operating instructions manual (8 pages)
Table of Contents
Advertisement
Quick Links
Table of Contents
and Instructions
Items included in system
Float switches
³/��" weep holes
Battery cables loose or battery defective 6,7
Instruction Manual & Safety Warnings
2
2
2
3
3
3
4
5
5
Testing the System
5
5
5
6
Technical support
6
Warranty
6
Combination Primary and Backup Sump Pump System
7
7
7
8
8
9
10
10
10
10
11
11
11
11
11
12
Scan the QR code
13
for more information
about the PS-C50
14
Combination Sump
15, 16
Pump System
Model PS-C50
IMPORTANT: Even if you have the Pro Series™ C50
Combination Sump Pump System installed by someone
else, you must read and follow the safety information
contained in this manual. Failure to do so could result in
property damage, serious injury, or death.
Advertisement
Table of Contents
Related Manuals for Glentronics PRO Series
Summary of Contents for Glentronics PRO Series
-
Page 1: Table Of Contents
Float switches Parts & Service Information Controllers Technical support ³/��" weep holes IMPORTANT: Even if you have the Pro Series™ C50 Replacement Parts Diagram & List Understanding the Warning Combination Sump Pump System installed by someone Scan the QR code... -
Page 2: Important Safety Warnings
BATTERY PREPARATION receptacle, have a licensed electrician replace the vicinity of the battery. it with a 3-prong receptacle according to • Use the Pro Series control unit for charging a Warnings & Instructions WARNING/POISON local codes and ordinances. LEAD-ACID battery only. DO NOT use the control Sulfuric acid can cause blindness or severe •... -
Page 3: Introduction
To extend the battery runtime, two batteries designed to work with your battery backup ends to connect the two batteries together may be connected to the Pro Series C50 • 1½" rigid PVC pipe to connect to the existing sump pump system. Glentronics can not (Model PJC, available from Glentronics, Inc.) -
Page 4: Installing The Pipe And Pump
(See Diagram A in column 1 below.) 8. Lift the combination system by the handle The Pro Series combination system is compact on the primary pump and lower it into the If you are replacing an old sump pump, unplug and will fit in a sump pit as small as 12"... -
Page 5: Battery Instructions
1' from the outlet. Plug the controller batteries may not be compatible with this into a properly grounded 3-prong outlet. system. The use of a Pro Series B12-100 Then plug the primary pump into the battery is HIGHLY recommended. receptacle on the controller. Using a... -
Page 6: Product Operation
• If the 4th light on the controller is also In the event that your Pro Series sump pump above the pump. on, check your main pump for failure. The This is normal. -
Page 7: Cleaning Battery Terminals
Remove the old battery from the battery The Pro Series control unit will check the 3. The control unit may have received a power box and place the new battery in the box. -
Page 8: Backup Pump Activated
Then call Glentronics technical activate. support for instructions at 800-991-0466. 2. Unplug the backup pump from the back of •... -
Page 9: Replacing The Primary Pump
REPLACING THE PRIMARY PUMP 7. Lay the pumps down and remove the three (3) screws holding the primary pump to Before you begin this the sump foot. The strainer on the primary process, you will need pump will separate from the pump when a new AC pump, new the screws are removed. -
Page 10: Battery Power Level
The Pro Series 2400 can be connected to 13. Lower the pump back into the pit by the with the Pro Series a home security system or other alarm handle of the primary pump. -
Page 11: Connect Module
Remove all debris from the float switch instructions on page 2. alarm will go off temporarily. Wait for the The Pro Series CONNECT Module is a cage. Lift the float up with a pencil, or another pump to stop pumping, and then push the separately sold accessory that will allow the nonmetallic item, and let go. -
Page 12: Replacement Parts Diagram & List
Replacement Parts List TOP VIEW PS-C50 Description Part Controller for backup pump PHCC-2400-CONT Enhanced dual float switch with controller for AC pump DFC1.5 ½ HP AC sump pump S3050-NS PHCC-2400 backup pump 1011013 Battery box 1113003 PVC wye pipe and 45° elbow 1120017 Sump foot 1143000... -
Page 13: Troubleshooting Guide
Clear debris from intake screen system from the outlet and battery terminals, then reconnect the system and push the reset button. If the problem continues, contact Glentronics customer service at 800-991-0466. Replace pump Defective pump ...... - Page 14 GLENTRONICS, INC., this warranty shall no longer be valid. Prior to defective operation, the unit must not have been previously altered, repaired or serviced by anyone other than GLENTRONICS, INC., or its agent; the serial number on the unit must not have been altered or removed; the unit must not have been subject to accident, misuse, abuse or operated contrary to the instructions contained in the accompanying manual.
-
Page 15: Other Products
ƒ Sends emails, texts or in-app notifications Compatible with: and status alerts to your phone, tablet or computer ƒ All current Pro Series backup and combo systems ƒ NO MONTHLY FEE ƒ Connect using home Wi-Fi Pro Series Maintenance Free/AGM Standby ƒ... - Page 16 USB port ƒ Detects as little as � /��" of water ƒ Use with the Pro Series Water Alarm ƒ Detect leaks before they become bigger when water reaches the sensor...
Need help?
Do you have a question about the PRO Series and is the answer not in the manual?
Questions and answers
How to remove pump switch to inspect it for malfunction?