Glentronics Pro Series Instruction Manual
  1. Manuals
  2. Brands
  3. Glentronics Manuals
  4. Service Equipment
  5. PRO Series
  6. Instruction manual

Glentronics Pro Series Instruction Manual

Battery backup sump pump system
Hide thumbs Also See for Pro Series:
Table of Contents

Advertisement

Quick Links

Download this manual
Battery Backup
Sump Pump System
Instruction
Manual
Push button 1 second to test or reset alarm.
Push 5 seconds to silence alarm for 24 hours.
Warning alarms
•
The fluid in the battery is low. Add distilled water.
•
The battery terminals are corroded or the battery is defective.
Clean the terminals or replace the battery.
•
The unit is not receiving AC power. Check the plug or circuit breaker.
To silence the alarm during emergencies, press the button for 5 seconds.
•
The pump is defective or not connected. Check plug or replace pump.
•
The pump was activated. Check the main pump for failure.
To silence the alarm during emergencies, press the button for 5 seconds.
Battery power level
•
100%
•
75%
•
50%
•
25%

Advertisement

Table of Contents
loading

Related Manuals for Glentronics Pro Series

Summary of Contents for Glentronics Pro Series

  • Page 1 Battery Backup Sump Pump System Instruction Manual Push button 1 second to test or reset alarm. Push 5 seconds to silence alarm for 24 hours. Warning alarms • The fluid in the battery is low. Add distilled water. • The battery terminals are corroded or the battery is defective. Clean the terminals or replace the battery.

  • Page 2: Table Of Contents

    Additional Items Needed ..2 An extension cord should not be used the Pro Series 2200 control unit. Do not unit to the NEGATIVE (-) post of the unless absolutely necessary. If an ex- use the control unit for charging dry-cell battery.

  • Page 3: Introduction

    If the main pump breaks or is unable to keep up with all the incoming water, the Pro Series pump is capable of running without discharging the battery as long as the AC power is on.

  • Page 4: Pump & Pipe

    Secure the pump wire so that the plug on the end will not fall into the PIPE ADAPTER sump. Attach the wire to the pipe MAIN AC PUMP PRO SERIES PUMP with a piece of tape. Diagram A Page 3...
  • Page 5 This will allow the pump to be HOSE CLAMPS removed easily, should the need PIPE ADAPTER arise. DRAIN TILE PRO SERIES PUMP The path of the rest of the pipe and the "L" BRACKET MAIN AC PUMP details of each installation will vary. Diagram Aa...

  • Page 6: Hookup To Existing Discharge Pipe

    AC pump. If the direct discharge method (Method A) is not possible, the Pro Series 2200 Secure the pump wire so that the backup sump pump system can be plug on the end will not fall into the hooked up to the same pipe as your AC sump.
  • Page 7 (2) stainless steel hose pipe above the check valve of the clamps. Position the bracket so the Pro Series pump, and attach a 45˚ bottom of the "L" is just above the elbow to that pipe. Extend another top of the main pump, and out of the piece of pipe to reach the "Y"...

  • Page 8: Battery Instructions

    (c) The acid The battery fluid sensor and cap are should reach a level just below the cap designed to fit the Pro Series batteries. (As ring. (Diagram C) a safety precaution, do not use the cap on...

  • Page 9: Control Unit Hookup

    BATTERY from the POSITIVE (+) post of the WIRE battery with the battery cap that is provided in the Pro Series sump pump package. An arrow on the top of the FLOAT SWITCH battery marks this position. There are Battery &...

  • Page 10: Understanding The Warning

    AC power is restored and the pumping energy reaches ⁄ hour or more. In the event that your Pro Series Sump Warning alarms • Pump System has been called on to The fluid in the battery is low. Add distilled water.

  • Page 11: Replacing The Battery

    7. SURGE PROTECTOR WHITE to the NEGATIVE (-) post The Pro Series 2200 control unit will and tighten the wing nuts. 4. Coat the battery terminals with a little check the pump and its wire con- petroleum jelly and replace the nections each week for possible pump 5.

  • Page 12: Replacing The Pump

    Glentronics, Inc., 1150 Willis Ave., Wheeling, IL 60090-5817 800-991-0466 If this warning goes on while the pump is ©2001, Glentronics, Inc. running, you will have a minimum of one...

This manual is also suitable for:

2200

Table of Contents